summaryrefslogtreecommitdiff
path: root/configs/dra7xx_evm_defconfig
AgeCommit message (Collapse)Author
2020-04-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-15Kconfig: Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMAVignesh Raghavendra
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use macros such as CONFIG_IS_ENABLED() that allow conditional compilation of code for SPL and U-Boot. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-12-13arm: ti: dra7: move BOOTP_DNS2 and PHY_TI in defconfigGrygorii Strashko
Move BOOTP_DNS2 and PHY_TI from dra7xx_evm.h to dra7xx_evm_defconfig. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-12-04mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flashMiquel Raynal
Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NANDMiquel Raynal
Add more clarity by changing the Kconfig entry name. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> [trini: Re-run migration, update a few more cases] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENTTom Rini
Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-25configs: dra7xx_evm: Increase the size of SPL_MULTI_DTB_FITFaiz Abbas
Expand SPL_MULTI_DTB_FIT to accommodate usb peripheral nodes being added to support SPL_DFU bootmode. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-25configs: dra7xx_evm: Add Kconfigs for SPL_DFU bootmodeFaiz Abbas
Enable configs for supporting SPL_DFU bootmode. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-09-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25Convert CONFIG_SYS_SPI_U_BOOT_OFFS to KconfigHannes Schmelzer
This converts the following to Kconfig: CONFIG_SYS_SPI_U_BOOT_OFFS Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> [trini: Expose this for SPL_SPI_SUNXI for now] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-04-29configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-12configs: ti_omap5_common: Add NAND environment settingsFaiz Abbas
Now that NAND is supported on DRA71x include various NAND environment settings Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-04-12configs: dra71x-evm: Add Support for NANDFaiz Abbas
Add NAND support to dra71x-evm defconfig Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-22configs: dra7xx_evm: Remove ENV_IS_IN_FATFaiz Abbas
With U-boot supporting environment in multiple places, enable only ENV_IS_IN_EMMC Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-07configs: Don't use SPI_FLASH_BAR as defaultVignesh R
Now that new SPI NOR layer uses stateless 4 byte opcodes by default, don't enable SPI_FLASH_BAR. For SPI controllers that cannot support 4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c, renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to not break functionality. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-01-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-10Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
- DM_I2C_COMPAT removal for all ti platforms from Jean-Jacques Hiblot - Fix in i2c command help output from Chirstoph Muellner.
2018-12-10dra7: Allow selecting a new dtb after board detection.Jean-Jacques Hiblot
The DRA7 platforms requires that the dtb used in the SPL really matches the platform to have the best MMC performances. To detect the board type/version an I2C EEPROM is read. This requires that DM is initialized before the detection. As a consequence we must reset the DM after the board detection is a new dtb would better match the platform. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10configs: dra7xx-evm: increase the size of the malloc's pool before relocationJean-Jacques Hiblot
This is required to take advantage of MULTI_DTB_FIT before relocation. If it is too low, DM will be initialized only after relocation has taken place. That is too late for the DRA7 because I2C DM is used before the relocation to setup the voltages required, among other things, to properly initialize the DRAM. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-07configs: enable DM_USB and DM_USB_DEV for all DRA7 platformsJean-Jacques Hiblot
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-11-13configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MISC_INIT_R to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-30usb: fastboot: Convert USB f_fastboot to shared fastbootAlex Kiernan
Convert USB fastboot code to use shared fastboot protocol. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-30fastboot: Move fastboot to drivers/fastbootAlex Kiernan
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to drivers/fastboot. Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing behaviour. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-27Convert CONFIG_SPI to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-13configs: dra7xx_evm/dra7xx_hs_evm: Enable AHCI and PIPE3Jean-Jacques Hiblot
Those options are required to enable support for SATA on DRA7 platforms. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-04-11spl: spi: Move CONFIG_SPL_SPI_LOAD to KconfigMarek Vasut
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
2018-04-08Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to KconfigAlex Kiernan
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2018-04-08Migrate CONFIG_DRIVER_TI_CPSW to KconfigAlex Kiernan
This converts CONFIG_DRIVER_TI_CPSW to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-13configs: dra7xx_evm: Enable support for the HS200 mmc mode in the SPLJean-Jacques Hiblot
Beside enabling the support for HS200 in mmc core, enabling the HS200 support in the SPL requires multi-dtb support in the SPL because pinctrl and IOdelays vary across SOCs. Also we need to make sure that the pinctrl properties arenot removed from the dts by setting CONFIG_OF_SPL_REMOVE_PROPS to remove only clocks and interrupts properties. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-23configs: Re-sync with CONFIG_DISTRO_DEFAULTSTom Rini
A number of platforms include config_distro_defaults.h but do not enable CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and re-sync config files. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-19configs: dra7xx_evm/dra7xx_hs_evm: Enable MMC HS200 and SD UHS supportJean-Jacques Hiblot
By default UHS and HS200 are not enabled. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-22Convert CONFIG_OMAP_USB_PHY to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_OMAP_USB_PHY Signed-off-by: Adam Ford <aford173@gmail.com>
2017-10-16configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-10cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-03cmd: fastboot: Rework fastboot dependencyMaxime Ripard
Fastboot need a bunch of options to be operating properly, such as the g_dnl gadget, the fastboot command, and some options that make sense. Since fastboot is now part of Kconfig, make sure we have them right. That will also reduce the boilerplate in the defconfigs. Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03usb: gadget: Make g_dnl USB settings commonMaxime Ripard
The g_dnl USB settings for the vendor ID, product ID and manufacturer are actually common settings that can and should be shared by all the gadgets. Make them common by renaming them, and convert all the users. Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
generated by cgit (git 2.34.1) at 2024-12-28 20:34:02 +0000