summaryrefslogtreecommitdiff
path: root/configs/hikey_defconfig
AgeCommit message (Collapse)Author
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-02-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-02-19hikey: Allow environment to store in eMMC and increase bootdelayManivannan Sadhasivam
Current Hikey configuration allows us to store u-boot environment on uSD card. But this will be useless if uSD card is not inserted, hence use the onboard eMMC memory for storing environment at Boot1 partition. While we are at it, let's increase the boot delay to 10s also. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-01-15mmc: Convert HI6220 MMC driver to driver modelManivannan Sadhasivam
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver model. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> [trini: Enable this on poplar] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-14configs: Migrate and re-enabled CONFIG_CMD_MTDPARTSTom Rini
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MISC_INIT_R to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-22Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
2018-03-16Convert all of CONFIG_CONS_INDEX to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11configs: Migrate CONFIG_SYS_TEXT_BASETom Rini
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-16configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-10cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-09-08usb: net: migrate USB Ethernet adapters to KconfigChris Packham
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08usb: net: migrate CONFIG_USB_HOST_ETHER to KconfigChris Packham
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14common: Move CONFIG_BOOTARGS to KconfigSam Protsenko
Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-31env: Migrate CONFIG_ENV_IS_IN_FAT options to KconfigTom Rini
We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that they can be modified via Kconfig. Migrate all existing users to the new values. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25Convert CONFIG_ENV_IS_IN_FAT to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_FAT Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-11usb: Kconfig: migrate USB_DWC2 to KconfigPhilipp Tomsich
This change migrates the USB_DWC2 configuration item to Kconfig and runs moveconfig to adjust header files and defconfig. Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com> Split off into a separate patch: Ran moveconfig to migrate other boards: Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-10configs: Resync defconfigsTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-0696boards: dragonboard/hikey: add device tree overlay supportPeter Robinson
96boards CE devices such as the DragonBoard and Hikey devices have numerous mezzanine options some of which need overlays from the beginning so it makes sense to enable device tree overlays. Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2017-06-03Kconfig: Migrate FS_FAT / FAT_WRITETom Rini
Now that these symbols are in Kconfig, migrate all users. Use imply on a number of platforms that default to having this enabled. As part of this we must migrate some straglers for CMD_FAT and DOS_PARTITION. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-08cmd: move CONFIG_CMD_UNZIP and CONFIG_CMD_ZIP to KconfigMasahiro Yamada
CONFIG_CMD_ZIP is not defined by any board. I am moving CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family. I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP" is better for this platform. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
2017-01-25Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-11mmc: move DesignWare-based drivers to KconfigMasahiro Yamada
Move (and rename) the following CONFIG options to Kconfig: CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS) CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3) CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA) The "HIKEY" is a board name, so it is not suitable for the MMC controller name. I am following the name used in Linux. This commit was generated as follows: [1] Rename the config options with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e ' s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g ' [2] Commit the changes [3] Create the entries in drivers/mmc/Kconfig (with default y for EXYNOS and SOCFPGA) [4] Run the following: tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA [5] Sort and align drivers/mmc/Makefile for readability [6] Clean-up doc/README.socfpga by hand Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-01-11mmc: move CONFIG_DWMMC to Kconfig, renaming to CONFIG_MMC_DWMasahiro Yamada
This commit was created as follows: [1] Rename the option with the following command: find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \ -type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g' [2] create the entry for MMC_DW in drivers/mmc/Kconfig (the prompt and help were copied from Linux) [3] run "tools/moveconfig.py -y MMC_DW" [4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry [5] Clean-up doc/README.socfpga by hand Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
2016-12-03Enable DISTRO_DEFAULT on platforms that missed it beforeTom Rini
A number of platforms had been using the distro default feature before it was moved to Kconfig but did not enable the new Kconfig option when it was enabled. This caused a regression in terms of features and this introduces breakage when more things move to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12common: Add DISPLAY_BOARDINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12common/Kconfig: Add DISPLAY_CPUINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-20Kconfig: Move config IDENT_STRING to KconfigSiva Durga Prasad Paladugu
Move the config IDENT_STRING to Kconfig and migrate all boards [sivadur: Migrate zynq boards] Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> [trini: Update configs, add some default to sunxi Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09configs: Migrate CONFIG_USB_STORAGETom Rini
In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09configs: Resync with savedefconfigTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-17configs: Re-sync BOOTDELAY changesTom Rini
With updated moveconfig.py and an better default, re-generate the migration of BOOTDELAY to the defconfig. Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-09common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig optionHeiko Schocher
move CONFIG_BOOTDELAY into a Kconfig option. Used for this purpose the moveconfig.py tool in tools. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-04-25ARM: hisilicon: hikey: Enable OF_CONTROL for hikey board.Peter Griffin
Currently only the serial pl01x driver is using DT, and the other drivers still use platform data but as more DT lands in the upstream kernel the aim is to migrate the other drivers over to DT as well to have a fully DT configured hikey u-boot. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync almost all of cmd/KconfigTom Rini
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync HUSH optionsTom Rini
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14Move CONFIG_OF_LIBFDT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing boards. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-18common: add CMD_GPIO to KconfigThomas Chou
Add CMD_GPIO to Kconfig and run tools/moveconfig.py . Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-09-28ARM: hikey: hi6220: Migrate over to DM_SERIAL and use UART3 by default.Peter Griffin
Use DM for the pl01x serial driver on hikey. Also allow UART0 or UART3 to be chosen via Kconfig. By default we now output to UART3 as the latest version of ATF outputs to this UART. Also UART3 comes out on the LS connector, as opposed to UART0 which goes to a unpopulated header. As part of this change we also enable CONFIG_BOARD_EARLY_INIT_F and call the pinmux configuration code for the UART. Before we were relying on ATF having already configured the pin configuration. NB: Upstream Linux kernel doesn't yet support UART3, so serial console will still be output on UART0 when booting a upstream kernel. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-09-28Reorder defconfigs with 'savedefconfig'Bin Meng
Some boards' defconfigs are disordered. Reorder them. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-12ARM64: hikey: hi6220: Add u-boot support for the 96boards CE HiKey board.Peter Griffin
HiKey is the first 96boards consumer edition compliant board. It features a hi6220 SoC which has eight ARM A53 cpu's. This initial port adds support for: - 1) Serial 2) eMMC / SD card 3) USB 4) GPIO It has been tested with Arm Trusted Firmware running u-boot as the BL33 executable. Notes: eMMC has been tested with basic reading of eMMC partition into DDR. I have not tested writing / erasing. Due to lack of clock control it won't be running in the most performant high speed mode. SD card slot has been tested for reading and booting kernels into DDR. It is also currently configured to save the u-boot environment to the SD card. USB has been tested with ASIX networking adapter to tftpboot kernels into DDR. On v2015.07-rc2 dhcp now works, and also USB mass storage are correctly enumerated. GPIO has been tested using gpio toggle GPIO4_1-3 to flash the LEDs. Basic SoC datasheet can be found here: - https://github.com/96boards/documentation/blob/master/hikey/ Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf Board schematic can be found here: - https://github.com/96boards/documentation/blob/master/hikey/ 96Boards-Hikey-Rev-A1.pdf Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
generated by cgit (git 2.34.1) at 2024-12-23 19:59:52 +0000