| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Enable I2C support for Engicam GEAM6UL NAND module.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable Flattened Image Tree support for all Engicam boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Create ubifs.img:
$ mkfs.ubifs -q -r /rootfs -m 4096 -e 253952 -c 7936 -o ubifs.img
Write ubifs.img:
---------------
icorem6qdl> nand erase.part rootfs
icorem6qdl> ubi part rootfs
icorem6qdl> ubi create rootfs
icorem6qdl> ext4load mmc 0:2 ${loadaddr} ubifs.img
166592512 bytes read in 8091 ms (19.6 MiB/s)
icorem6qdl> ubi write ${loadaddr} rootfs ${filesize}
166592512 bytes written to volume rootfs
icorem6qdl> ubifsmount ubi0:rootfs
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
For writing Linux or rootfs on to NAND, the best suitable way
is to use MMC commands since MMC driver by default enabled by
mx6_common.h, hence enabled MMC commands in nand defconfigs.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Boot Linux with uImage instead of zImage, so update
bootz with bootm.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Generated by "tools/moveconfig -s".
This will make config moves easier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add FEC support for Engicam GEAM6UL module.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add NAND support for Engicam GEAM6UL board.
Boot Log:
--------
U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28)
Trying to boot from NAND
NAND : 256 MiB
U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100)
CPU: Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 42C
Reset cause: WDOG
Model: Engicam GEAM6UL
DRAM: 128 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
* Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
