summaryrefslogtreecommitdiff
path: root/configs/mt7623n_bpir2_defconfig
AgeCommit message (Collapse)Author
2020-05-08configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-01arm: enable distro boot for bananapi-r2Matthias Brugger
This patch enables distro boot for the bananapi-r2, based on a MediaTek mt7623n. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-01-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-16configs: mediatek: fix mt7623n bpir2 defconfigSam Shih
This patch add CONFIG_TARGET_MT7623 into mt7623n_bpir2_defconfig to fix the mt7623 compile error after building others mediatek target platform Signed-off-by: Sam Shih <sam.shih@mediatek.com> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
2019-12-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-30configs: enable CONFIG_BLOCK_CACHE for mt7623n_bpir2Weijie Gao
This patch enables CONFIG_BLOCK_CACHE for mt7623n_bpir2. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-01-19configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-18adding saveenv-command for bananapi r2Frank Wunderlich
bananapi r2 can be booted from sd-card and emmc saving the environment have to choose the storage from which the device has booted also the offset is set to 1MB to make sure env is written to block "user data area" between uboot and first partition https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.png Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2019-01-14configs: MediaTek: use OF_SEPARATE instead of OF_EMBEDWeijie Gao
This patch replace OF_EMBED with OF_SEPARATE of defconfig files of MediaTek boards because now OF_EMBED is only used for debugging purpose. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-14arm: MediaTek: add ethernet support for MT7623 boardsWeijie Gao
Enable ethernet related configs to mt7623n_bpir2_defconfig. Add default IP addresses. Enable noncached memory region required by ethernet driver. Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
2019-01-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-28arm: MediaTek: add basic support for MT7623 boardsWeijie Gao
This adds a general board file based on MT7623 SoCs from MediaTek. As this u-boot is loaded by MTK proprietary preloader, there is no low level initializtion codes. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Tested-by: Matthias Brugger <matthias.bgg@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>