| Age | Commit message (Collapse) | Author |
|---|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Fix the Kconfig warning to not use CONFIG_OF_EMBED in defconfigs.
Based on https://patchwork.ozlabs.org/patch/1019791/
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
It's a Spansion (s25fl064a) 8 MB SPI flash.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
