summaryrefslogtreecommitdiff
path: root/configs/orangepi_pc_defconfig
AgeCommit message (Collapse)Author
2019-04-29configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-10arm: sunxi: Enable DRAM ODT by default on H3/H5Paul Kocialkowski
Most of the boards we support with H3/H5 enable DRAM on-die termination, which is consistent with the high DRAM clocks that are used. Make it the default (like it's done for other similar platforms) instead of defining it in each defconfig. Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-10arm: sunxi: Set the default DRAM ZQ value to 3881979 on H3/H5Paul Kocialkowski
Most H3/H5 boards we support have the DRAM ZQ value set to 3881979, which is also consistent with the default set for the R40. Make this value the default on H3/H5 instead of 123. Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-02-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-18sunxi: usb: Switch to Generic host controllersJagan Teki
Onc of key blocker for using USB Generic host controller drivers in Allwinner are CLK and RESET drivers, now these available for USB usage. So switch sunxi USB use EHCI and OHCI Generic controllers. Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD where it already have USB_EHCI_HCD Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-03configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-16part: Disable CONFIG_SPL_ISO_PARTITION by defaultAlexander Graf
We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot could load distro images that usually get shipped as iso images. These images usually come with a board agnostic boot environment. However, there is very little point in having ISO support enabled (for anyone really) in SPL, as the whole idea of SPL is to load U-Boot proper which again is board specific. So the fact that we enable ISO support in U-Boot proper does not mean at all that we want ISO support in U-Boot SPL. Hence, let's remove the Kconfig dependency. Along the way, let's also clean up all those default configs that disabled SPL ISO support. Signed-off-by: Alexander Graf <agraf@suse.de>
2018-04-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-14sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigsAndre Przywara
Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence of moving the common definition shared by almost every sunxi board into 123 individual defconfig files. But the U-Boot start address for Allwinner boards is a platform decision which has been around for ages, so defining it in each *board* config file seems a bit over the top. Define the standard values (160MB into DRAM for most SoCs, with two SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from the individual defconfigs. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-02-11configs: Migrate CONFIG_SYS_TEXT_BASETom Rini
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-05cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGATuomas Tynkkynen
cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2017-10-10cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-09-01configs: Migrate all of the existing USB symbols, except fastbootTom Rini
This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-19configs: Resync defconfigsTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-13configs: Re-syncTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-28disk: convert CONFIG_EFI_PARTITION to KconfigPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-28disk: convert CONFIG_ISO_PARTITION to KconfigPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-28disk: convert CONFIG_DOS_PARTITION to KconfigPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2016-10-23Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV CONFIG_CONSOLE_MUX Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-order, re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-16Convert CONFIG_SPL_I2C_SUPPORT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-09configs: Resync with savedefconfigTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-31sunxi: Re-enable h3 emac supportHans de Goede
With the recent bug fixes for the sun8i_emac driver all known issues are resolved, so we can re-enable the driver. While at it, also enable the emac on the Orange Pi One. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Jagan Teki <jteki@openedev.com>
2016-07-27sunxi: Disable sun8i emac driverHans de Goede
Disable the sun8i emac driver for now, there are 2 issues with it: 1) It is causing issues with network connectivity under the kernel driver, when booting the kernel with v2 of Corentin's sun8i-h3 emac driver, I get the connection status bouncing between connected at 100mbps full-duplex and being down every second. The second issue is that when trying to use it from u-boot I get a number of unaligned cache flush errors: => dhcp BOOTP broadcast 1 BOOTP broadcast 2 CACHE: Misaligned operation at range [7bf594a8, 7bf59628] BOOTP broadcast 3 CACHE: Misaligned operation at range [7bf59c90, 7bf59e10] CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8] DHCP client bound to address 10.42.43.80 (1009 ms) Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26sunxi: Add defconfig and dts file for the Orange Pi PC Plus SBCHans de Goede
There is a new Orange Pi PC *Plus* version available now, this is an extended version of the regular Orange Pi PC with sdio wifi and an eMMC. The upstream kernel devs have decided that they want a separate dts for the PC Plus rather then sharing a single dts between the regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig to match. The added dts file matches the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15sunxi: orangepi_pc: Add support for eMMC found on the Orange Pi PC PlusHans de Goede
The Plus variant of the Orange Pi PC has an eMMC, add support for this. Note we are using the same u-boot defconfig / dts for both the regular Orange Pi PC as well as the Orange Pi PC Plus. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-15net: Add EMAC driver for H3/A83T/A64 SoCs.Amit Singh Tomar
This patch add EMAC driver support for H3/A83T/A64 SoCs. Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY). BIG Thanks to Andre for providing some of the DT code. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-17configs: Re-sync BOOTDELAY changesTom Rini
With updated moveconfig.py and an better default, re-generate the migration of BOOTDELAY to the defconfig. Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-09common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig optionHeiko Schocher
move CONFIG_BOOTDELAY into a Kconfig option. Used for this purpose the moveconfig.py tool in tools. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-05-25sunxi: Enable a bunch of commands by default on sunxiHans de Goede
Recently a set of CONFIG_CMD_FOO defines was moved from being defined in config_distro_defaults to Kconfig, and added to all sunxi defconfigs to compensate. Instead of explictly selecting these in all sunxi defconfigs, simply always select these for sunxi boards. This makes the defconfigs simpler and ensures a consistent set of available commands across all sunxi boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync almost all of cmd/KconfigTom Rini
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync HUSH optionsTom Rini
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-12sunxi: Enable CMD_GPIO on all sunxi boardsHans de Goede
We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after its Kconfig conversion it has ended up missing on some recently added boards. Simply select it for ARCH_SUNXI, so that we get it on all sunxi boards for both a consistent user experience and simpler defconfig files. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23sunxi: Specify USB vbus pins for orangepi boardsHans de Goede
This fixes the USB ports not working on the orangepi_plus and stops us from messing with gpio-s which we should not touch on the orangepi_pc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-02-23sunxi: H3: Add support for the host usb-physJelle van der Waa
Add support for phy 1-3. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> [hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-02-23sunxi: power: add support for sy8106a driverJelle van der Waa
SY8106A is a PMIC which is used on the Allwinner H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is implemented to set the default V-CPU voltage to 1200 mV. This driver is required to ensure the SY8106A V-CPU voltage is set to 1200 mV after a software reset. On cold boot the default SY8106A output voltage is selected to be 1200 mV by a pair of resistors on the Orange Pi PC and Plus. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-21sunxi: Add support for the I2C controller which is part of the PRCMJelle van der Waa
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> [hdegoede@redhat.com: Minor cleanups] Signed-off-by: Hans de Goede <hdegoede@redhat.com> applied with fixing 2 checkpatch warnings: WARNING: please, no space before tabs Signed-off-by: Heiko Schocher <hs@denx.de>
2015-12-27sunxi: Reduce Orangepi PC RAM speed to 624 MHzHans de Goede
There are some reports of stability issues at 672 MHz, see: http://linux-sunxi.org/Orange_Pi_PC#DRAM_clock_speed_limit So reduce the DRAM speed to 624MHz which seems to be reliable everywhere. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-12-10sunxi: select SYS_NS16550 from KconfigHans de Goede
Select SYS_NS16550 from Kconfig instead of setting it in all our defconfig files. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-25spi: Move SPI drivers to defconfigBin Meng
There are already Kconfig options for SPI drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-22sunxi: Update new defconfigsTom Rini
After introduction of CONFIG_SYS_NS16550 these defconfig files were added and need to be updated. Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-22sunxi: Add support for Orangepi Plus and Orangepi PC boardsHans de Goede
Add defconfig files for the Orangepi Plus and Orangepi PC. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
generated by cgit (git 2.34.1) at 2024-12-24 19:27:15 +0000