| Age | Commit message (Collapse) | Author |
|---|
|
With HDMI output for the RK3399 working, this update the RK3399-Q7
(Puma) defconfig for the new functionality:
1. enables PMIC command (to check if the HDMI voltages are correct)
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
2. enables video-output (via HDMI)
+CONFIG_DM_VIDEO=y
+CONFIG_DISPLAY=y
+CONFIG_VIDEO_ROCKCHIP=y
+CONFIG_DISPLAY_ROCKCHIP_HDMI=y
3. turns on the 'dcache'-command (for a dcache flush) for our QA to
fill the framebuffer using 'mw.l'
+CONFIG_CMD_CACHE=y
4. turns on the 'bmp'-command
+CONFIG_CMD_BMP=y
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
For the RK3399-Q7 module, we use full OF_CONTROL (i.e. not
OF_PLATDATA) for SPL. In this configuration, the rockchip_dw_mmc
driver retrieves one of its clocks via clk_get_by_name and fails if
this is not possible. For this reason, we can not filter clock-names
from the device-tree nodes used for the configuration of the SPL
stage.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The RK3399-Q7 exposes I2C on its edge connector and uses it as one of
the interfaces towards the on-module STM32 (for the emulated RTC and
fan-controller).
Enable I2C and CMD_I2C support in the defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The RK3399-Q7 has a KSZ9031 GbE PHY. Enable support for it in defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
On the RK3399-Q7, we need PMIC support (for the RK808) to enable HDMI
output, as one of the required powerrails is not enabled on boot.
For this, we need to enable the RK808 driver.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 3
- With the recent upstream changes to the RK808 (PMIC) driver, the
associated configuration options have been renamed to RK8XX. Track
this change in the RK3399-Q7 defconfig.
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
With everything in place (i.e. the new efuse driver, the clk-support
for the non-secure efuse block, and the board-specific functions to
derive 'serial#' from the cpu-id within the efuses), enable this in
the RK3399-Q7 defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This originally started out as
"pinctrl: Kconfig: reorder to keep Rockchip options together"
and tried to keep the Rockchip-related config options together.
However, we now rewrite all chip-specific driver selections to start
with CONFIG_PINCTRL_ (with the inadvertent changes to related
Makefiles) and sort those alphabetically. And as this already means
touching most of the file, we also reformat the help text to not exceed
80 characters (but make full use of those 80 characters).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit interace)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI displays
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This commit adds the baseline defconfig for the RK3399-Q7 (Puma) SoM
(under the name 'puma-rk3399_defconfig') featuring the Rockchip RK3399
in a Qseven compatible module.
This subsumes the following changes:
* defconfig: rk3399: migrate CONFIG_SPL_LIBCOMMON_SUPPORT/CONFIG_SPL_LIBGENERIC_SUPPORT
* defconfig: rk3399-puma: add CONFIG_MMC_DW_ROCKCHIP
* defconfig: rk3399-puma: disable CONFIG_SPL_OF_PLATDATA
* defconfig: rk3399-puma: don't USE_TINY_PRINTF
* defconfig: rk3399-puma: set up CONFIG_SYS_BOARD for the RK3399-Q7
* defconfig: rk3399-puma: enable the multi-image loading via CONFIG_SPL_FIT
* defconfig: rk3399-puma: SPL should be able to boot from MMC/SD card
* defconfig: rk3399-puma: enable GMAC support
* defconfig: rk3399-puma: enable support for SPI and Winbond SPI flash
* defconfig: rk3399-puma: enable SPI as a boot-source in SPL
* defconfig: rk3399-puma: disallow non-FIT images from being loaded
* defconfig: rk3399-puma: rename to puma-rk3399
* rockchip: config: rk3399: update defconfigs and rk3399_common
For the RK3399-Q7, we want a default boot-order of SPI -> MMC -> uSD.
This both follows how the BootROM probes devices and is a sane default
for customers in device-personalisation (e.g. it allows for quick and
easy factory programming of unpersonalised devices using an SD card)
and field usage (with customer devices expected to have their firmware
either in SPI or MMC).
However, when probing multiple interfaces (according to the result
from the board_boot_order function), we need to ensure that only valid
FIT images are considered and disable the fallback to assuming that a
raw (binary-only) U-Boot image is loaded (to avoid hangs/crashes from
jumping to random content loaded from devices that are probed, but
don't contain valid image content).
By disabling the SPL_RAW_IMAGE_SUPPORT and SPL_LEGACY_IMAGE_SUPPORT
options, we ensure that raw images (indistinguishable from random
data) are not considered for booting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop CONFIG_DEBUG_UART_BOARD_INIT:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
