| Age | Commit message (Collapse) | Author |
|---|
|
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
To reduce the default image size CONFIG_CMD_NVEDIT_EFI was disabled by
default. Re-enable it on the QEMU platforms supporting the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Enable CONFIG_CMD_BOOTEFI_SELFTEST for the QEMU RISC-V boards.
Travis CI QEMU testing has been enabled for qemu-riscv64_defconfig. With
this patch we will test the UEFI sub-system on the board.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Enable distro boot on the qemu-riscv32/64 boards. Supported boot target
devices are VirtIO and DHCP.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
|
|
Support booting Linux (as payload of BBL) from FIT images. For this, the
default CONFIG_SYS_BOOTM_LEN is increased to 16 MB, and the environment
variables fdt_high and initrd_high are set to mark the device tree and
initrd as in-place.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
QEMU provides a device tree, which is passed to U-Boot using register
a1. We are now able to directly select the device tree with the
configuration CONFIG_OF_PRIOR_STAGE. Replace the hard-coded address in
qemu-riscv with it.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
RISC-V defines the base integer instruction sets as RV32I and RV64I.
Rename CPU_RISCV_32 and CPU_RISCV_64 to ARCH_RV32I and ARCH_RV64I to
match this convention.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
