Age | Commit message (Collapse) | Author |
|
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable iminfo command with CONFIG_CMD_IMI
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
For sama5d2_xplained_mmc_defconfig, we have the following layout for SD-Card:
partition 1: FAT: contains bootstrap binary (second level bootloader),
U-boot, U-boot env, kernel, dtb
partition 2: EXT4: Rootfs.
Add to defconfig CONFIG_ENV_FAT_DEVICE_AND_PART to have environment
by default on SD-Card, to align with our demo layout.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
To support loading the zImage + DTB from the rootfs ext4 partitions,
enable the ext4 command support.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
ATMEL_SPI is now fully converted to driver-model and
respective boards switch to DM_SPI as well,
so make default y for ARCH_AT91
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Use the Atmel PIT timer driver which supports the driver model
and device tree.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig. Migrate all existing users to the new
values.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FAT
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Enable CONFIG_DM_ETH to make MACB to support driver model.
Because the USB Ether doesn't support driver model so far,
remove this feature.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_AT91".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Currently, CONFIG_MMC is not related to any other options by
"depends on" or "select". One of big advantages of using Kconfig
is automatic dependency tracking, but the current state is lacking
it. As the first step, make the existing MMC driver entries depend
on MMC.
This commit was created by the following steps:
[1] Run the following script:
--------------------8<--------------------
rm -f tmp.txt
for d in $(find . -path './configs/*_defconfig')
do
if grep -q -e 'CONFIG_MSM_SDHCI=y' $d ||
grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d ||
grep -q -e 'CONFIG_SH_SDHI=y' $d ||
grep -q -e 'CONFIG_PIC32_SDHCI=y' $d ||
grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d ||
grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d ||
grep -q -e 'CONFIG_SANDBOX_MMC=y' $d
then
echo CONFIG_MMC=y >> $d
echo ${d#./configs/} >> tmp.txt
fi
done
tools/moveconfig.py -y -s -d tmp.txt
rm tmp.txt
--------------------8<--------------------
[2] surround MMC driver entries with "if MMC" and "endif"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Generated by "tools/moveconfig -s".
This will make config moves easier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Enable an early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Move the config options from the include/configs/sama5d2_xplained.h
to configs/sama5d2_xplained_*_defconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|