summaryrefslogtreecommitdiff
path: root/configs/stm32mp15_trusted_defconfig
AgeCommit message (Collapse)Author
2020-07-07configs: stm32mp1: activate CONFIG_GPIO_HOGPatrick Delaunay
This patch activates the new configuration CONFIG_GPIO_HOG. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14configs: stm32mp1: activate CONFIG_ERRNO_STRPatrick Delaunay
Add support of errno_str, used in command pmic and regulator. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14configs: stm32mp1: activate Ethernet PHY RealtekChristophe Roullier
Need Realtek driver to manage in RTL8211F the configuration of the LED. Initialize LCR (LED Control Register) to configure green LED for Link, yellow LED for Active Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-14stm32mp: stm32prog: add MTD devices supportPatrick Delaunay
Add support of MTD device (DFU_MTD backend) for NOR, NAND or SPI-NAND target. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp: stm32prog: add MMC devicePatrick Delaunay
Add support of MMC device (based on DFU_MMC backend) for SD card and eMMC update. Create a GPT partitioning on the device. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp: add the command stm32progPatrick Delaunay
Add a specific command stm32prog for STM32MP soc family witch allows to program the boot devices with the tool STM32CubeProgrammer (http://www.st.com/STM32CubeProg). This command uses the same UART STM32 protocol than MCU STM32 with or USB with DFU protocol v1.1 (ithe MCU ST extension are no supported). The executed actions are based on a tab separated value file with a stm32 header, the FlashLayout file (https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout). This file is parsed by the U-Boot command to: - initialize the devices - create the partition table on each device - initialize the DFU backend to access to not volatile memory (NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC) Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout. The communication between U-Boot and STM32CubeProgrammer is done with the specific alternate configuration (see "AN5275: USB DFU/USART protocols used in STM32MP1 Series bootloaders" for details). The command stm32prog is executed when a boot from USB is detected (selected with bootpins) and we can program the boot devices with a simple command (on Windows or Linux): PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv 1/ the ROM code loads TF-A in embedded RAM (DFU or uart) 2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart) 3/ U-Boot executes the stm32prog command (DFU or uart) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp1: dynamically detect op-tee presencePatrick Delaunay
Activate OP-TEE driver for trusted and optee defconfig. This driver allows detection of TEE presence for boot from flash; CONFIG_STM32MP1_OPTEE is also removed. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08configs: migrate CONFIG_SYS_MTDPARTS_RUNTIME to defconfigsPatrick Delaunay
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-08configs: migrate CONFIG_SET_DFU_ALT_INFO to defconfigsPatrick Delaunay
Move CONFIG_SET_DFU_ALT_INFO into Kconfig done by moveconfig.py. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-04-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-15ARM: stm32: Enable bootd, iminfo, imxtract on ST defconfigPatrick Delaunay
Enable these standard U-Boot commands for image manipulation and for starting the default boot command using 'boot' command in U-Boot shell. Cc: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-04-15configs: stm32mp1: replace STM32MP1_TRUSTED by TFABOOTPatrick Delaunay
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT introduced by the commit 535d76a12150 ("armv8: layerscape: Add TFABOOT support"). This config CONFIG_TFABOOT is activated for the trusted boot chain, when U-Boot is loaded by TF-A. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-06video: enable VIDEO_ANSI and all VIDEO_BBP optionsAnatolij Gustschin
This partially reverts changes by commit 2cc393f32fd9 ("video: make BPP and ANSI configs optional") since it caused issues with other boards (missing LCD console output on pinebook, x86 platform or sandbox). Enable all disabled options again and opt out of not supported color depth in board defconfigs. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reported-by: Vagrant Cascadian <vagrant@debian.org>
2020-01-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-17stm32mp1: split board and SOC support for STM32MP15x familyPatrick Delaunay
Split the board and SOC support for STM32MP15x family and prepare the introduction of new boards with STM32MP15x. This path define the 2 configurations: - STM32MP15x: STM32MP15x soc support (new) - TARGET_ST_STM32MP15x: STMicroelectronics board support (choice) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-01-17board: stm32mp1: move CONFIG_ENV_XXX in defconfigPatrick Delaunay
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig for ST board with NOR support (STM32MP15xx-EV1 boards) - CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB) - CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH) This Patch prepares the U-Boot support of boards with STM32MP15x SOC not provided by STMicroelectronics. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-01-07configs: stm32mp15: Enable random number generator(rng) deviceSughosh Ganu
Enable support for the rng device on the stm32mp15 configs. Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-12-18stm32mp1: configs: Resync with savedefconfigPatrick Delaunay
Rsync all defconfig files using moveconfig.py Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-12-06video: make BPP and ANSI configs optionalAnatolij Gustschin
Many boards do not use all selected framebuffer depth configurations, for such boards there is some unused code in video and console uclass routines. Make depth specific code optional to avoid dead code and slightly reduce binary size. Also make ANSI code optional for the same reason. When i.e. using only VIDEO_BPP16 the code size shrinks (below values when using gcc-7.3.0): $ ./tools/buildman/buildman -b video-wip -sS wandboard ... 01: Merge git://git.denx.de/u-boot-sh 02: video: add guards around 16bpp/32bbp code 03: video: make BPP and ANSI configs optional arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0 Signed-off-by: Anatolij Gustschin <agust@denx.de> Tested-by: Eugen Hristev <eugen.hristev@microchip.com> Tested-by: Patrice Chotard <patrice.chotard@st.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2019-12-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flashMiquel Raynal
Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03mtd: rename CONFIG_MTD -> CONFIG_DM_MTDMiquel Raynal
CONFIG_MTD must be reserved for the MTD core. Like any other subsystem, prefix the symbol by DM when it comes to DM support. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Add Kconfig files] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NANDMiquel Raynal
Add more clarity by changing the Kconfig entry name. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> [trini: Re-run migration, update a few more cases] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-26stm32mp1: add support for virtual partition readPatrick Delaunay
Add read for OTP and PMIC NVM with alternates on virtual DFU device. Serie-cc: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-11-26stm32mp1: configs: activate CONFIG_MTD_SPI_NANDPatrick Delaunay
Activate the support of SPI NAND in stm32mp1 U-Boot. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-11-26stm32mp1: activate DFU support and command MTDPatrick Delaunay
Add support of DFU for MMC, MTD, RAM and MTD command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENTTom Rini
Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-13stm32mp1: configs: add display devicesYannick Fertré
Add support of panels otm8009A, RM68200 & DSI controller. Limit resolution to 1280x800. Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-08-27stm32mp1: Add remoteproc support for m4 coprocessorPatrick Delaunay
Alignment with kernel patch proposal for binding: [PATCH v4 0/8] stm32 m4 remoteproc on STM32MP157c https://lkml.org/lkml/2019/5/14/159 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: add CONFIG_CMD_BMPPatrick Delaunay
Activate command BMP for splash screen support Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: add BACKLIGHT_GPIO supportPatrick Delaunay
Backlight of panel raydium RM68200 is controlled by a simple gpio, thus we activate the support for the needed driver. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: add CONFIG_DM_VIDEOPatrick Delaunay
Activate command DM_VIDEO for LCD support Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: Deactivate SPI_FLASH_BARPatrick Delaunay
Remove CONFIG_SPI_FLASH_BAR as the SPI NOR layer uses stateless 4 byte opcodes by default. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: select CONFIG_STM32_SERIALPatrick Delaunay
Select the serial driver mandatory for the console. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-22rtc: Add rtc driver for stm32mp1Patrick Delaunay
Add support of STM32MP1 rtc driver. Enable it for basic and trusted configurations. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
2019-07-22configs: stm32mp15: enable stm32 remoteprocPatrick Delaunay
Activate the remote processor support for stm32mp15 configs. Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-07-12stm32mp1: activate OF_BOARD_SETUP and FDT_FIXUP_PARTITIONSPatrick Delaunay
Update kernel MTD partition in device tree with U-Boot information. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12stm32mp1: deactivate WATCHDOG in defconfigPatrick Delaunay
Deactivate WATCHDOG by default in u-boot to avoid issue to boot kernel and rootfs without the needed daemon to reload it. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
2019-07-12configs: stm32mp15: enable IPCC mailboxFabien Dessenne
Activate the ipcc mailbox for stm32mp15 configs. Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-07-09env: ubi: KConfig: add CONFIG_ENV_UBI_VOLUME_REDUNDMarkus Klotzbuecher
Introduce the KConfig option CONFIG_ENV_UBI_VOLUME_REDUND for defining the name of the UBI volume used to store the redundant environment. Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Kyungmin Park <kmpark@infradead.org> hs: get rid of stm32mp1* build errors
2019-06-18configs: stm32mp15: Select correct Ethernet driver for trusted modePatrice Chotard
Select the correct Ethernet driver from Synopsis. Initially, "Synopsys Designware Ethernet MAC" driver was wrongly selected instead of "Synopsys DWC Ethernet QOS device" driver. Fixes: commit f90b3f5b68ed ("configs: stm32mp15: Enable Ethernet feature") Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable Ethernet featureChristophe Roullier
This allows to enable Ethernet and use driver for Synopsys Ethernet QoS device Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-06-06configs: stm32mp15: Enable SPI relative flagsPatrice Chotard
Enable STM32_SPI, SPI, DM_SPI and CMD_SPI flags. This enables the SPI support for STM32MP15. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable WDT flagsPatrice Chotard
This allows to enable WATCHDOG and WDT flags to be able to reset the watchdog and to support watchdog driver model. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable ENV_IS_SPI_FLASHPatrice Chotard
Add all relative flags needed by ENV_IS_IN_SPI_FLASH Reserved a 256KB partition in NOR to save the U-Boot environment. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
generated by cgit (git 2.34.1) at 2024-12-29 16:08:00 +0000