summaryrefslogtreecommitdiff
path: root/configs/stm32mp15_trusted_defconfig
AgeCommit message (Collapse)Author
2019-10-13stm32mp1: configs: add display devicesYannick Fertré
Add support of panels otm8009A, RM68200 & DSI controller. Limit resolution to 1280x800. Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-08-27stm32mp1: Add remoteproc support for m4 coprocessorPatrick Delaunay
Alignment with kernel patch proposal for binding: [PATCH v4 0/8] stm32 m4 remoteproc on STM32MP157c https://lkml.org/lkml/2019/5/14/159 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: add CONFIG_CMD_BMPPatrick Delaunay
Activate command BMP for splash screen support Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: add BACKLIGHT_GPIO supportPatrick Delaunay
Backlight of panel raydium RM68200 is controlled by a simple gpio, thus we activate the support for the needed driver. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: add CONFIG_DM_VIDEOPatrick Delaunay
Activate command DM_VIDEO for LCD support Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: Deactivate SPI_FLASH_BARPatrick Delaunay
Remove CONFIG_SPI_FLASH_BAR as the SPI NOR layer uses stateless 4 byte opcodes by default. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: configs: select CONFIG_STM32_SERIALPatrick Delaunay
Select the serial driver mandatory for the console. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-22rtc: Add rtc driver for stm32mp1Patrick Delaunay
Add support of STM32MP1 rtc driver. Enable it for basic and trusted configurations. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
2019-07-22configs: stm32mp15: enable stm32 remoteprocPatrick Delaunay
Activate the remote processor support for stm32mp15 configs. Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-07-12stm32mp1: activate OF_BOARD_SETUP and FDT_FIXUP_PARTITIONSPatrick Delaunay
Update kernel MTD partition in device tree with U-Boot information. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12stm32mp1: deactivate WATCHDOG in defconfigPatrick Delaunay
Deactivate WATCHDOG by default in u-boot to avoid issue to boot kernel and rootfs without the needed daemon to reload it. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
2019-07-12configs: stm32mp15: enable IPCC mailboxFabien Dessenne
Activate the ipcc mailbox for stm32mp15 configs. Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-07-09env: ubi: KConfig: add CONFIG_ENV_UBI_VOLUME_REDUNDMarkus Klotzbuecher
Introduce the KConfig option CONFIG_ENV_UBI_VOLUME_REDUND for defining the name of the UBI volume used to store the redundant environment. Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Kyungmin Park <kmpark@infradead.org> hs: get rid of stm32mp1* build errors
2019-06-18configs: stm32mp15: Select correct Ethernet driver for trusted modePatrice Chotard
Select the correct Ethernet driver from Synopsis. Initially, "Synopsys Designware Ethernet MAC" driver was wrongly selected instead of "Synopsys DWC Ethernet QOS device" driver. Fixes: commit f90b3f5b68ed ("configs: stm32mp15: Enable Ethernet feature") Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable Ethernet featureChristophe Roullier
This allows to enable Ethernet and use driver for Synopsys Ethernet QoS device Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-06-06configs: stm32mp15: Enable SPI relative flagsPatrice Chotard
Enable STM32_SPI, SPI, DM_SPI and CMD_SPI flags. This enables the SPI support for STM32MP15. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable WDT flagsPatrice Chotard
This allows to enable WATCHDOG and WDT flags to be able to reset the watchdog and to support watchdog driver model. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable ENV_IS_SPI_FLASHPatrice Chotard
Add all relative flags needed by ENV_IS_IN_SPI_FLASH Reserved a 256KB partition in NOR to save the U-Boot environment. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable ENV_IS_IN_UBIPatrice Chotard
Add all relative flags needed by ENV_IS_IN_UBI Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable ENV_IS_IN_EXT4 and all relative flagsPatrick Delaunay
Enable ENV_IS_IN_EXT4 and all relative flags to be able to load/save environment in EXT4 partition. This will allows to load/save environment on both sdcard and eMMC. As for stm32mp15, bootfs has not the same partition number on sdcard and on eMMC, we use "auto" key which allows to find the first partition in device with bootable flag which is partition 4 on sdcard and partition 2 on eMMC. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06stm32mp1: activate NAND and NOR support on EV1Patrick Delaunay
Add the necessary configuration to have NAND and NOR support on ev1 board for BASIC boot (with SPL) or for TRUSTED boot (with TF-A). STM32MP> nand info Device 0: nand0, sector size 256 KiB Page size 4096 b OOB size 224 b Erase size 262144 b subpagesize 4096 b options 0x00184200 bbt options 0x00060000 STM32MP> sf probe SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, total 64 MiB Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-04-21stm32mp1: migrate USBOTG device to driver modelPatrick Delaunay
Use the DWC2 device driver with DM_USB_GADGET support and cleanup the USB support in STM32MP1 board. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-21stm32mp1: remove CONFIG_USB_DWC2, HOST support for USBOPatrick Delaunay
Remove the HOST support for STM32MP1 USBO device = OTG DWC2. The current DWC2 driver have no dynamic detection of device, So it is dangerous to have start 3V3 when PC is connected to the micro USB connector. => it is preferable to have only DEVICE support CONFIG_USB_GADGET_DWC2_OTG for OTG port See DWC3 driver for clean dual role support... Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12config: stm32mp15: Enable STMFX supportPatrick Delaunay
Activate PINCTRL_STMFX and needed part for generic pincontrol PINCTRL_FULL, PINCONF. Increase pre-reloc memory for MALLOC (needed for each DM pinconfig node). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12power: rename stpmu1 to official name stpmic1Patrick Delaunay
Alignment with kernel driver name & binding introduced by https://patchwork.kernel.org/cover/10761943/ to use the final marketing name = STPMIC1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12stm32mp1: activated some configurationPatrick Delaunay
Add configuration useful for test - FIT support - MEMTEST - DFU - CACHE - TIME - TIMER Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: activate FASTBOOT on eMMCPatrick Delaunay
activate Fastboot for eMMC on EV1 board (mmc1) $> sudo apt-get install android-tools-adb android-tools-fastboot $> fastboot -i 0x0483 getvar bootloader-version Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update bootcmdPatrick Delaunay
Clearly separate bootcmd for stm32mp1 board (bootcmd_stm32mp) and preboot management. That solve issue for fastboot continue command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: cosmetic cleanup KconfigPatrick Delaunay
Cosmetic cleanup in mach-stm32mp Kconfig - remove duplicated SPL_DRIVERS_MISC_SUPPORT - update help for TARGET_STM32MP1 - set value for NR_DRAM_BANKS - remove one comment as DEBUG_UART is deactivated by default - include board Kconfig at the end of the file Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add trusted boot with TF-APatrick Delaunay
Add support of trusted boot, using TF-A as first stage bootloader, The boot sequence is BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32 The TF-A monitor provides secure monitor with support of SMC - proprietary to manage secure devices (BSEC for example) - PSCI for power The same device tree is used for STMicroelectronics boards with basic boot and with trusted boot. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
generated by cgit (git 2.34.1) at 2024-12-27 01:02:40 +0000