summaryrefslogtreecommitdiff
path: root/configs/stmark2_defconfig
AgeCommit message (Collapse)Author
2019-05-26configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-24configs: add DM_SPI config optionAngelo Dureghello
This patch adds CONFIG_DM_SPI for all m68k boards using the cf_spi.c driver (DSPI module). Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2019-05-24configs: enable use of DT for all m68k boardsAngelo Dureghello
Enable DT usage for all m68k boards. To provide a working single binary, the dts has been kept as embedded. Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2019-03-25Convert CONFIG_ENV_SPI_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-08-06spi: Kconfig: Create ISSI Kconfig entryMichal Simek
Add ISSI to Kconfig to make it selectable via menuconfig. Also convert all current platforms. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-22Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
2018-04-27Convert CONFIG_SPI to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-27Kconfig: cmd: Make networking command dependent on NETMichal Simek
Enable networking command only when NET is enabled. And remove selecting NET for CMD_NET Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-13spi: Migrate CONFIG_CF_SPI to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-05cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGATuomas Tynkkynen
cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2017-11-12board: sysam: stmark2: add missing environment locationAngelo Dureghello
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-11-05Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini
We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-10cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-08-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-18m68k: add board stmark2, mcf5441x basedAngelo Dureghello
Sysam stmark2 board is a generic and fully (hw and sw) open board, with a mcf54415 Coldfire CPU, 128MB of DDR2, 16MB of SPI flash and SD card as non volatile memories, and a wifi module included on-board. The board is actually used mainly for Coldfire custodian testing activity related to the mcf5441x Coldfire family. For further information please see: http://sysam.it/cff_stmark2.html Signed-off-by: Angelo Dureghello <angelo@sysam.it> --- Changes in v2: - remove CMD_REGINFO - add board information in commit message
generated by cgit (git 2.34.1) at 2024-12-27 03:06:17 +0000