summaryrefslogtreecommitdiff
path: root/configs/uniphier_v8_defconfig
AgeCommit message (Collapse)Author
2018-11-14configs: Migrate and re-enabled CONFIG_CMD_MTDPARTSTom Rini
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-25ARM: uniphier: enable MTD partition and UBIMasahiro Yamada
Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to use UBI on NAND devices. Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because enabling UBI would increase 170KB, which would be memory footprint problem. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-22Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-23ARM: uniphier: enable CONFIG_SNI_AVE and disable CONFIG_SMC911XMasahiro Yamada
Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig. Disable the on-board SMC911x because it has not migrated to the driver model yet - it is not possible to enable DM and non-DM drivers at the same time. The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept because the on-chip ethernet driver for LD4, sLD8 is not supported yet. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-08ARM: uniphier: enable CONFIG_PINCONFMasahiro Yamada
Enable the pin configuration feature for UniPhier 64 bit SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-02-23Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-10configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-05cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGATuomas Tynkkynen
cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-01-28ARM: uniphier: enable HS200 support for uniphier_v8_defconfigMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-01-09ARM: uniphier: enable CONFIG_MMC_SDHCI_SDMA for ARMv8 SoCsMasahiro Yamada
I did not enable SDMA when I added sdhci-cadence support because LD20 boards are equipped with a large amount memory beyond 32 bit address range, but SDMA does not support the 64bit address. U-Boot relocates itself to the end of effectively available RAM. This would make the MMC enumeration fail because the buffer for EXT_CSD allocated in the stack would go too high, then SDMA would fail to transfer data. Recent SDHCI-compatible controllers support ADMA, but unfortunately U-Boot does not support ADMA. In the previous commit, I hided the DRAM area that exceeds the 32 bit address range. Now, I can enable CONFIG_MMC_SDHCI_SDMA. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-26Move CONFIG_PANIC_HANG to KconfigMasahiro Yamada
Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-18configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-29ARM: uniphier: set CONFIG_LOGLEVEL to 6Masahiro Yamada
Print out KERN_NOTICE or higher level log messages. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-20net: Add SMC911X driver to Kconfig, convertAdam Ford
We add the various SMC91XX symbols to drivers/net/Kconfig and then this converts the following to Kconfig: CONFIG_SMC911X CONFIG_SMC911X_BASE CONFIG_SMC911X_16_BIT CONFIG_SMC911X_32_BIT Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Apply to the rest of the tree, re-squash old and new patch] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-15ARM: uniphier: enable DWC3 xHCI driverMasahiro Yamada
Enable CONFIGs for the DWC3 core and the UniPhier specific glue layer. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-10cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-09-02Kconfig: Add EEPROM options to Kconfig when I2C_EEPROM is setAdam Ford
Add the following options to drivers/misc/Kconfig: SYS_I2C_EEPROM_ADDR SYS_I2C_EEPROM_BUS SYS_EEPROM_SIZE SYS_EEPROM_PAGE_WRITE_BITS SYS_EEPROM_PAGE_WRITE_DELAY_MS SYS_I2C_EEPROM_ADDR_LEN SYS_I2C_EEPROM_ADDR_OVERFLOW This does not migrate any boards, but provides a foundations for those who want/need these options Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Migrate uniphier] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-30ARM: uniphier: enable Denali NAND driver for 64bit SoCsMasahiro Yamada
Now the entry to the NAND driver init can be is controlled by DT; it should not hurt to compile the driver all the time. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-14configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-26ARM: uniphier: enable CONFIG_CMD_FS_GENERICMasahiro Yamada
Enable file system commands such as load, ls. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-20ARM: uniphier: enable PSCI sysreset for uniphier_v8_defconfigMasahiro Yamada
This configuration is supposed to be used with ARM Trusted Firmware, so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of U-Boot's own reset code because we need to coordinate with SCP (System Control Processor) for the system-level power management. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-03-13configs: Re-syncTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-23ARM: uniphier: enable CONFIG_CMD_CONFIGMasahiro Yamada
This command is useful to see which config options are enabled on the running U-Boot image. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23ARM: uniphier: enable CONFIG_CMD_GPTMasahiro Yamada
Enable CONFIG_CMD_GPT, keeping CONFIG_SPL_EFI_PARTITION because the SPL for UniPhier platform does not recognize any partitions. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23ARM: uniphier: disable CONFIG_MTD_NOR_FLASHMasahiro Yamada
This feature is seldom used these days on UniPhier boards. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23ARM: uniphier: enable generic EHCI driver for uniphier_v8_defconfigMasahiro Yamada
The LD11 SoC is equipped with USB EHCI controllers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-12flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-24Kconfig: Migrate BOARD_LATE_INIT to a selectTom Rini
This option should not really be user selectable. Note that on PowerPC we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be conditional on that. Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
2017-01-22ARM: uniphier: add uniphier_v8_defconfigMasahiro Yamada
This defconfig does not support SPL. If you use this, the basic SoC initialization must be done in firmware that runs before U-Boot. (Generally, ARM Trusted Firmware is expected to do this job). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit (git 2.34.1) at 2024-12-26 13:14:09 +0000