| Age | Commit message (Collapse) | Author |
|---|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
1. Commit 3a7c45f6a772 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver") causes some i.MX boards that were converted
to DM, such as warp7, to fail to boot.
As explained by Lukas Auer:
"With the patch, U-Boot probes the drivers for devices under simple-bus
device tree nodes in the pre-relocation device model. The default value
of CONFIG_SYS_MALLOC_F_LEN (0x4000) leaves U-Boot with not enough memory to
do this, causing it to hang."
Fix this problem by providing a convenient default value for
CONFIG_SYS_MALLOC_F_LEN.
2. CONFIG_SPL_TEXT_BASE was moved to Kconfig, so added in defconfig
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133eef2e068f9c33853b6584d7fcbfa9d2e)
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.
CPU: Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@02020000
Out: serial@02020000
Err: serial@02020000
Net: FEC0
Working:
- Eth0
- i2c
- MMC/SD
- eMMC
- USB host
- UART 1
Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
|
