summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2019-10-08imx8qxp_mek: switch to use container imagePeng Fan
Because FIT could not be used for AHAB secure boot on i.MX8, so switch to use container image that could let SPL verify ATF and U-Boot with AHAB. Note: The AHAB related code has not been added. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6sabresd: fix usb start when DM enabledPeng Fan
Enable CONFIG_DM_REGULATOR_FIXED to let vbus regulator work. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08Kconfig: Migrate CONFIG_CSF_SIZE to KconfigBreno Matheus Lima
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000. mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08mx6sabresd: Reduce overall SPL sizeFabio Estevam
Currently the SPL binary is 67 kB, which leaves only 1 kB of free internal RAM space. The following options can be safely removed to save some precious SPL space: - CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd command (at offset 69 kB) - CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL - CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported by default After this change the SPL binary size gets down to 51 kB. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Enable fuse comamndPeng Fan
Enable fuse command Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix wrong i2c configuration nameYe Li
Wrong I2c driver configuration name is used in codes, so I2c driver is not built. Correct it. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb bootPeng Fan
Since the SD3.0 kernel driver needs M4 image support, this causes problem for usb boot booting into kernel. To decouple the relationship, we modify the FDT file in u-boot to disable SD3.0. So the kernel won't depend on M4 image. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08configs: nitrogen6x: Add DM_SPI/DM_SPI_FLASH supportTroy Kisky
Add CONFIG_DM_SPI/CONFIG_DM_SPI_FLASH to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_GPIO supportTroy Kisky
Add CONFIG_DM_GPIO to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This is in preparation for adding CONFIG_DM_SPI. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_MMC/DM_USB/AHCI supportTroy Kisky
Add DM_MMC to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This commit is adding multiple configs, but seems to be the minimum change to not lose features and still compile fine. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08nitrogen6x: migrate to using device treeTroy Kisky
Migrate to using device tree required for further driver model integration. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08imx: mx6slevk: enable DM_SPI and DM_SPI_FLASHPeng Fan
With DM_SPI and DM_SPI_FLASH enabled, we could get: spi 0 [ ] mxc_spi | | | `-- ecspi@02008000 spi_flash 0 [ ] spi_flash_std | | | `-- m25p80@0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6ul_14x14_evk: convert to DM_VIDEOPeng Fan
To support DM_VIDEO, Add display node for lcdif Drop board iomuxc settings. Enable DM_VIDEO Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08imx: add i.MX6ULZ boardPeng Fan
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible with i.MX6ULL. so most code of i.MX6ULL can be reused by i.MX6ULZ. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08arm64: versal: remove debug uart for versal virtIbai Erkiaga
Remove the debug uart configuration from versal virtual defconfig. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Introduce virtual defconfigIbai Erkiaga
Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Introduce virtual defconfigIbai Erkiaga
Add virtual defconfig for ZynqMP architecture using of_board dtb. This defconfig should become generic config for all ZynqMP boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Enable clock driverMichal Simek
Enable clock driver for Versal. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Enable random mac generationMichal Simek
In case that mac address is not found it is generated randomly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Enable cache by defaultMichal Simek
The whole cache code needs to be redesign to read information about cache from DT instead of macro selection. Enable caches by default because systems have caches on by default for Linux. Also enable CMD_CACHE to be able to disable cache if there is any issue. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Define default SYS_PROMPTMichal Simek
All boards are using the same prompt that's why add it as default value to Kconfig to simplify defconfigs. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2019-10-08ARM: zynq: Define default SYS_PROMPTMichal Simek
All boards are using the same prompt that's why add it as default value to Kconfig to simplify defconfigs. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add a2197 memory board revAMichal Simek
Similar to processor board but i2c structure is completely different. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add System Controller for a2197-g/pMichal Simek
Similar SCs but different wiring. - dc_i2c is connected to X-PRC cards that's why label is required to have an option to hook up some devices. - Exactly identify i2c devices on x-prc boards. In case of missing i2c connection devices won't be accessible. - USB 0 should be device mode with super speed. - USB 1 should be host mode. - Fix i2c mux reset pin entry - commented, not verified. - Fix i2c1 eeprom compatible string - it is an ST 128Kbit device. Need to use atmel fallback. - Fix si570 I2C slave address and add corresponding part numbers. - Enable AMS for system monitoring. - phy reset property should be commented because it will throw a warning dump when called from context that can sleep. No support for phys property (zynqmp phy driver) with SGMII. Add is-internal-pcspma property required by uboot. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
2019-10-08arm64: zynqmp: Add generic a2197 system controller configMichal Simek
Add generic configuration for a2197-p/-m/-g boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Remove unneeded configs for mini configurationsSiva Durga Prasad Paladugu
The PSCI_RESET and EXPERT are not needed for mini configurations so remove them to save space. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: mini_emmc: Enable fatwrite supportSiva Durga Prasad Paladugu
This patch enable fatwrite support for mini emmc configurations. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
2019-10-08arm64: zynqmp: Enable 2 NAND chips support for zynqmp_mini_nandT Karthik Reddy
This patch enables 2 nand chips support for zynqmp mini nand Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Define board_late_init for versalSiva Durga Prasad Paladugu
Define board_late_init which performs bootmode detection and prepares corresponding distro boot commaand sequence. Also disable it for mini platforms because simply there is no need to have it enabled. But also disable it for virtual platform because Qemu is not modelling this register space that's why travis testing would fail. This configuration should be reverted when mainline Qemu is updated. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Enable SPI support in SPL for zcu104Michal Simek
It is enabling this mode but full boot is not validated yet. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Enable gpio hog support for zcu102Michal Simek
Gpio hogs are used for GT mux setup after power up. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Define default SPL_TEXT_BASE address in KconfigMichal Simek
Define default address via Kconfig. There is no need to change this address for most of the boards but it is also possible. This one line save a lot of lines in defconfigs that's why make sense to do it. The similar change has been done by commit 9340d8fe8beb ("sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2019-10-08configs: sam9x60ek: enable onewire supportEugen Hristev
Enable support for onewire memories and onewire commands. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08configs: Add sam9x60ek_qspiflash_defconfigTudor Ambarus
Boot from QSPI nor flash. The at91bootstrap, u-boot, u-boot env redundant, u-boot env, device tree and kernel will reside in the QSPI nor flash. The rootfs will reside in the NAND flash. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08configs: Add sam9x60ek_nandflash_defconfigTudor Ambarus
Boot from nand flash. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08configs: Add sam9x60ek_mmc_defconfigSandeep Sheriker Mallikarjun
add sam9x60ek_mmc_defconfig and for now only supports booting from sdcard. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> [nicolas.ferre@microchip.com: split patch, add Ethernet controller, phy and tools] [claudiu.beznea@microchip.com: add CONFIG_OF_LIBFDT_OVERLAY] Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> [tudor.ambarus@microchip.com: Fix number of DRAM banks: One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks] Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08board: atmel: sama5d27_wlsom1_ek: fix SPL OFFS on SPIEugen Hristev
Fixes redefinition of CONFIG_SYS_SPI_U_BOOT_OFFS This is now a Kconfig Fixes: e40a9ba6d2d5 ("board: atmel: sama5d2_wlsom1_ek: add qspi support and qspi boot config") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08configs: sama5d27_wlsom1_ek: add CONFIG_SPL_AT91_MCK_BYPASSEugen Hristev
This board has an external oscillator as MCK that does not need driving. Bypass the driving for the main oscillator in SPL. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: dts: at91: sama5d27_wlsom1: add hlcdc nodeEugen Hristev
Add node for hlcld for u-boot logo display at boot. This is compatible with the Precision Design Associates (PDA) TM5000 screen. Timings are compatible with simple panel from Linux, panel name is pda_91_00156_a0 Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: sama5d2_wlsom1_ek: add qspi support and qspi boot configEugen Hristev
Add support for qspi memory on board. Created boot support for QSPI for both u-boot proper and SPL. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: sama5d2_wlsom1_ek: add SPL supportEugen Hristev
Add support for SPL for this board: DRAM initialization, PMC initialization, MMC boot. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: add sama5d27_wlsom1_ek boardNicolas Ferre
Add support for the SAMA5D27-WLSOM1-EK. It's based on the Microchip WireLess SoM which contains the SAMa5D27 LPDDR2 2Gbits SiP. Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> [eugen.hristev@microchip.com]: added u-boot specific dtsi and ported to 2019.10 Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08spl: Convert CONFIG_SPL_SIZE_LIMIT to hexSimon Glass
This is currently a decimal value which is not as convenient or meaningful. Also U-Boot tends to use hex everywhere. Convert this option to hex and add a comment for the size_check macro. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: correct the typo in the commit title] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08spl: Allow tiny printf() to be controlled in SPL and TPLSimon Glass
At present there is only one control for this and it is used for both SPL and TPL. But SPL might have a lot more space than TPL so the extra cost of a full printf() might be acceptable. Split the option into two, providing separate SPL and TPL controls. The TPL setting defaults to the same as SPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08x86: Change condition for using CARSimon Glass
At present we assume that CAR (Cache-as-RAM) is used if HOBs (Hand-off blocks) are not, since HOBs typically indicate that an FSP is in use, and FSPs handle the CAR init. However this is a bit indirect, and for FSP2 machines which use their own CAR implementation (such as apollolake) but use the FSP for other functions, the logic is wrong. To fix this, add a dedicated Kconfig option to indicate when CAR is used. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: fix a typo in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08watchdog: move WATCHDOG_TIMEOUT_MSECS to KconfigHeiko Schocher
move WATCHDOG_TIMEOUT_MSECS to Kconfig and fix all board defconfigs. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Martyn Welch <martyn.welch@collabora.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-10-06arm: socfpga: disable CONFIG_SPL_WDT for gen5 and a10Simon Goldschmidt
These boards don't have a watchdog enabled in SPL, so make sure CONFIG_SPL_WDT is not enabled. Fixes: commit 6874cb72204f ("watchdog: Split WDT from SPL_WDT") Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-04Kconfig: Migrate CONFIG_BOOTM_* optionsTom Rini
Migrate all of the existing OS support options that are under CONFIG_BOOTM_* to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-01rpi4: enable dram bank initializationMatthias Brugger
When booting through the efi stub, the memory map get's created by reading the dram bank information. Depending on the version of the RPi4 this information changes. Read the device tree to initialize the dram bank data structure. This way the kernel is able to access the whole range of available memory. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-30arm: at91: gardena-smart-gateway-at91sam: Enable CONFIG_SYS_NAND_USE_FLASH_BBTStefan Roese
This patch enables the BBT in NAND on the AT91SAM based GARDENA smart Gateway. This is especially important, since the Linux driver also enables this option and uses the BBT table pages. Without setting this option, U-Boot will try to re-use these pages again (e.g. UBI). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2025-01-17 00:49:00 +0000