summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2017-11-20odroid-c2: enable I2CBeniamino Galvani
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-17Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMANDTom Rini
We first introduce CONFIG_USE_BOOTCOMMAND, similar to CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex scheme around this usage, and these have been defered for the moment so that platform maintainers can work on a migration plan. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-11-17configs: dragonboard410c: Save environment data on eMMCJorge Ramirez-Ortiz
Save the environment data at the end of the boot partition on emmc Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-11-17arm: amlogic: p212: Add support for Ethernet with Internal PHYNeil Armstrong
This patch adds support for the Internal RMII Ethernet PHY on the Amlogic P212 Reference Board. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17arm: add initial support for Amlogic P212 based on Meson GXL familyNeil Armstrong
This adds platform code for the Amlogic P212 reference board based on a Meson GXL (S905X) SoC with the Meson GXL configuration. This initial submission only supports UART and MMC/SDCard, support for the internal Ethernet PHY in Work In Progress. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-16Merge git://www.denx.de/git/u-boot-marvellTom Rini
2017-11-16arm: mvebu: clearfog: Fix SPI-NOR flash accessJon Nettleton
The production variant of the SPI flash used by the clearfog devices are based on winbond chips. Additionally enable SPI_FLASH_BAR since some variants will have 16MB of flash that requires this to be enabled. Remove the default speed and mode; these values are taken from the device tree when CONFIG_DM_SPI_FLASH is enabled. Add default bus, so that 'sf' detects the SPI flash by default. Signed-off-by: Jon Nettleton <jon@solid-run.com> [baruch: remove speed/mode; add bus; move winbond to defconfig] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16arm: mvebu: clearfog: enable XHCI USBJon Nettleton
Enable the driver by default for the clearfog boards since the external port is configured for XHCI. Signed-off-by: Jon Nettleton <jon@solid-run.com> [baruch: split from the SoC setup patch] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16arm: mvebu: configs: Enable DISTRO_DEFAULTS for MACCHIATObinHeinrich Schuchardt
Enable DISTRO_DEFAULTS for mvebu_db_armada8k_defconfig mvebu_mcbin-88f8040_defconfig Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16arm: mvebu: theadorable_debug_defconfig: Enable setexpr commandStefan Roese
The setexpr command is useful for scripting, lets enable it for this platform. Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-15armv8: ls1088ardb: Add distro boot supportAshish Kumar
Distro boot support gives flexibility to run distro RFS like Ubuntu being deployed from SD card or SATA drive. If it fails to detect external storage, fall back to qspi/sd boot. Enable this by default in RDB's defconfig by selecting CONFIG_DISTRO_DEFAULTS Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Zhang Ying <zhangying@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088aqds: Add SD boot support for ls1088qdsAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088ardb: Add SD boot support for ls1088Ashish Kumar
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14armv8: ls1088a: Move CONFIG_SPI_FLASH_SPANSION to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-12board: sysam: stmark2: add missing environment locationAngelo Dureghello
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-11-09Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2017-11-09imx:display5: Add support for LWN's DISPLAY5 boardLukasz Majewski
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-07mx25: Move MX25 selection to KconfigFabio Estevam
The motivation for moving MX25 selection to Kconfig is to be able to better handle MX25 specific errata, so that an errata option can be selected at SoC level instead of board level. This selection method also aligns with the way other i.MX SoCs are selected in U-Boot. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2017-11-07rockchip: remove SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR from defconfigKever Yang
Use default value 0x4000 for SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR instead of define a new one. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-05Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini
We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-01rockchip: lion-rk3368: defconfig: select PHY_MICREL_KSZ90X1Philipp Tomsich
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1 in the associated defconfig. References: da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig") Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-01rockchip: puma-rk3399: defconfig: select PHY_MICREL_KSZ90X1Philipp Tomsich
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1 in the associated defconfig (this somehow got lost with da3b9e7f). References: da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig") Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-31Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2017-10-31ARM: imx6: Enable UMS and DFU on DHCOM i.MX6 PDKMarek Vasut
Enable UMS and DFU, so that the eMMC can be accessed via the USB gadget port on the board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2017-10-31mx6slevk: Fix MMC breakage for the SPL targetFabio Estevam
Commit 001cdbbb32ef1f6 ("imx: mx6slevk: enable more DM drivers") breaks MMC support in U-Boot proper on the mx6slevk_spl_defconfig target: U-Boot SPL 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18) Trying to boot from MMC1 U-Boot 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18 -0300) CPU: Freescale i.MX6SL rev1.0 792 MHz (running at 396 MHz) CPU: Commercial temperature grade (0C to 95C) at 33C Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0 MMC Device 1 not found *** Warning - No MMC card found, using default environment As mx6slevk_spl_defconfig does not use CONFIG_DM_MMC and its board file does not register the mmc controller for U-Boot proper, let's fix this by adding CONFIG_DM_MMC=y and device tree support. While at it, add more DM drivers, so that it becomes closer to mx6slevk_defconfig. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-30imx: Fix regression with CONFIG_DM_MMC=yFabio Estevam
When CONFIG_DM_MMC=y, CONFIG_BLK should be selected, otherwise the SD/eMMC card cannot be used. Also, select CONFIG_DM_USB=y when CONFIG_USB=y to avoid build failure. Tested on mx6slevk, mx7dsabresd and mx6ullevk. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Adam Ford <aford173@gmail.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Tested-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-30configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-27Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2017-10-27armv8: ls1088aqds: Enable USB command on QDS for qspi-bootRan Wang
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27armv8: ls1088ardb: Enable USB command RDB qspi-bootRan Wang
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27armv8: ls1088: Move CONFIG_ENV_IS_IN_SPI_FLASH to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27Merge git://git.denx.de/u-boot-x86Tom Rini
2017-10-27x86: galileo: Fix boot failureBin Meng
With latest codes on mainstream master, Intel Galileo board does not boot unfortunately. Git biset leads to b383d6c0 "bootstage: Convert to use malloc()". Disable bootstage support to make it boot again. The root cause needs to be investigated however. Fixes: b383d6c0 ("bootstage: Convert to use malloc()") Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-10-25sunxi: Add support for the Banana Pi M2-MagicMaxime Ripard
The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a wifi chip and some pin headers. Enable support for it. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25SPL: SPI: select SPL_SPI_FLASH_SUPPORT on SPL_SPI_SUNXIAndre Przywara
The Allwinner SPI flash SPL boot support is guarded by the SPL_SPI_SUNXI symbol. But despite its generic name, the actual only use case for this is to provide SPI flash support to the SPL, which requires CONFIG_SPL_SPI_FLASH_SUPPORT to be defined. Select this symbol from the SPL_SPI_SUNXI Kconfig definition. This avoids doing this explicitly in the defconfig, and fixes SPI booting on the Pine64 SoPine (and -LTS version) and the OrangePi Win board (both with SPI flash). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-23chiliboard config: use CONFIG_DEFAULT_FDT_FILE as env variableMichal Oleszczyk
Remove hardcoded ftd file name from environment variables. Use CONFIG_DEFAULT_FDT_FILE macro instead. Signed-off-by: Michal Oleszczyk <m.oleszczyk@grinn-global.com>
2017-10-23ARM: uniphier: enable DWC3 xHCI driver reallyMasahiro Yamada
I thought commit d37d31849c6a ("ARM: uniphier: enable DWC3 xHCI driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3 was missing in uniphier_v7_defconfig. Re-add. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-21uniphier_ld4_sld8: Re-add SMC911X_BASE addressTom Rini
This was dropped by accident in the Kconfig conversion. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20net: Add SMC911X driver to Kconfig, convertAdam Ford
We add the various SMC91XX symbols to drivers/net/Kconfig and then this converts the following to Kconfig: CONFIG_SMC911X CONFIG_SMC911X_BASE CONFIG_SMC911X_16_BIT CONFIG_SMC911X_32_BIT Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Apply to the rest of the tree, re-squash old and new patch] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_NAND_MXC CONFIG_NAND_OMAP_GPMC CONFIG_NAND_OMAP_GPMC_PREFETCH CONFIG_NAND_OMAP_ELM CONFIG_SPL_NAND_AM33XX_BCH CONFIG_SPL_NAND_SIMPLE CONFIG_SYS_NAND_BUSWIDTH_16BIT Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> [trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues, add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-19x86: conga-qeval20-qa3-e3845-internal-uart_defconfig: Add ACPI resume supportStefan Roese
I've missed to add the ACPI resume support to this x86 build target. This patch adds the ACPI resume support enabling S3 suspend / resume. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-10-19x86: provide CONFIG_BUILD_ROMHeinrich Schuchardt
Up to now we depended on an exported variable to build u-boot.rom. We should be able to specify it in the configuration file, too. With this patch this becomes possible using the new Kconfig option CONFIG_BUILD_ROM. This option depends on CONFIG_X86 and is selected in qemu-x86_defconfig and qemu-x86_64_defconfig. Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-10-19x86: minnowmax: Adjust VGA rom addressBin Meng
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image can be built again. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2017-10-16configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-15ARM: uniphier: enable DWC3 xHCI driverMasahiro Yamada
Enable CONFIGs for the DWC3 core and the UniPhier specific glue layer. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-13Merge tag 'signed-efi-next' of git://github.com/agraf/u-bootTom Rini
Patch queue for efi - 2017-10-13 This is the second batch of amazing improvements for efi_loader in 2017.11: - New self tests to verify our own code - A few bug fixes - colored text support - event and SNP improvements, should get us close to iPXE working
2017-10-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2017-10-12ARM: imx6: Add DHCOM i.MX6 PDK board supportMarek Vasut
Add support for the DHCOM i.MX6 PDK board. This board has: - FEC ethernet - EHCI USB host - 3x SDMMC Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2017-10-12mx6slevk: Use PARTUUID to specify the rootfs locationFabio Estevam
mx6slevk can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the SD card changes depending on the kernel version. In order to avoid such issue, use the UUID method to specify the rootfs location. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-12wandboard: Add support for the latest revd1 revisionFabio Estevam
Latest wandboard hardware revision is revd1, which brings the following new features: - PFUZE100 PMIC - AR8035 Ethernet PHY - Upgrade Wifi/BT chip to BCM4339/BCM43430. The detection mechanism is to probe the PMIC and when it is found, then the revision of the board is revd1. As the detection is done via PMIC, we need to print the board version at a later stage via CONFIG_DISPLAY_BOARDINFO_LATE and also need to disable CONFIG_DISPLAY_BOARDINFO, which is done much earlier. Make the necessary adjustments for the AR8035 PHY to work on revd1. Based on Richard Hu's work from Technexion's U-Boot tree. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-28 11:15:38 +0000