| Age | Commit message (Collapse) | Author |
|---|
|
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Adds esbc validate command for verification of MC and DPC
firmware, along with secure boot defconfig.
Also enable distro boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: squash "enable DM support for SATA patch" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Add u-boot enviroments to support distro boot which scan
boot.scr from external storage devices
(e.g. SD/USB/SCSI disk) and execute autoboot script
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Enable support for FAN controller EMC2305 for
LX2160A RDB board.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[PK: enable EMC2305 for lx2160rdb]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
LX2160ARDB is an evaluation board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han
and re-arrange defconfig]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Enable CONFIG_DM_SCSI and CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
CONFIG_BLK can be safely enabled as DM_MMC and DM_USB are already enabled.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
|
|
The commit 1bac199e8c87 ("configs: Resync with savedefconfig")
did remove ethernet driver from following boards defconfig:
- brppt1_mmc
- brppt1_nand
- brppt1_spi
With this commit we add ethernet and responsible phy support again.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
u-boot-imx-2019-02-16
---------------------
- vhybrid: add calibration
- gw_ventana: fixes
- Improve documentation for Secure Boot (HABv4)
- Fix Marvell Switch
- MX6 Sabre, switch to DM
- Fixes for NAND
|
|
Xilinx changes for v2019.04-rc2
xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs
i2c:
- Remove !DM_I2C zynq driver
versal:
- Enable some more features
- Add mini configurations
|
|
With DM and FIT enabled in SPL, there is an sram overflow. By disabling
CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and
CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all'
for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Add the DM_GPIO related config for mx6sabreauto.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Add the DM_GPIO related config for mx6sabresd.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Enable all the necessary configs for SPL DM and FIT support for
mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Enable all the necessary configs for SPL DM and FIT support for
mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Add the DM support for USB. For that, DM_REGULATOR is needed.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Add DM_MMC config to imx6sabreauto defconfig.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
This patch fixes a few values that were incorrect, and this
now lets SPL boot from NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
- MMC CD pin fix on Orangepi Zero plus
- SPI boot for Olinuxino Lime2-eMMC boards
- Change in dram frequnecy for tbs_a711
|
|
All options have been moved to Kconfig and there is no need to have
board header files. Mini configurations require them that's why they are
still there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Replace SDHCI controller listing by Kconfig symbol to let SPL know that
this board is using multiple SDHCIs controllers.
Kconfig help message should explain why this is needed.
Origin symbols were used in full u-boot but with moving to distro boot
this was fixed already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
All these board have also eeprom enabled that's why it is also enabled
via defconfig.
There is also no need to have zc70x specific config file that's why also
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no need to see this info. It is just wasting of space/time.
It saves 308Bytes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This platform is going to become generic that's why it is necessary also
enable different PHY vendors.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Convert board from OF_EMBED to OF_SEPARATE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
creating Xilinx distribution bootcommand and wiring it as the last
bootcommand.
QSPI, NAND distribution boot command will be added later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
It should not be necessary to adjust CMD_BOOTEFI_HELLO_COMPILE in config
files.
arch/arm/lib/crt0_arm_efi.S cannot be compiled in thumbs mode. We can
disable CMD_BOOTEFI_HELLO_COMPILE for CONFIG_CPU_V7M. So there is no longer
a need to disable it in stm32 configs.
helloworld.efi can be built without problems on x86_64. So there is no need
to disable it in chromebook_link64_defconfig and qemu-x86_64_defconfig.
Same is true for ARM V7A. So do not disable CMD_BOOTEFI_HELLO_COMPILE in
kp_imx6q_tpc_defconfig.
Some architecture checks are already make for EFI_LOADER. There is no need
to repeat them for CMD_BOOTEFI_HELLO_COMPILE
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice.Chotard@st.com
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The dram chip on the tablet was changed. The new one requires a lower
frequency, so change it.
Frequency 564MHz was also stable in the tests, but use slightly lower one
to be on a safe side.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
[jagan: add MHz in commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
There is no need for Intel Edison to have CONFIG_OF_EMBED to be enabled.
Replace it with CONFIG_OF_SEPARATE.
There is no functional change since u-boot.bin always contains DTB
either embedded or attached.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
|
|
The Detection pin is at PF6 and not at PH13 like defined before. I
checked the schematics and now I am am not seeing this error message any
more:
Loading Environment from FAT... Card did not respond to voltage select!
CONFIG_MMC_SUNXI_SLOT_EXTRA is also not needed because the second MCC
slot is for the Wifi card.
Fixes: 76d69eb01de ("sun50i: h5: Add initial Orange Pi Zero Plus support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Starting from revision K the Olimex-Lime2-eMMC boards include
eMMC 5.x chip. Unfortunately, the internal brom in the A20
cannot reliably initialize those chips resulting in random
boot failures on those boards.
To overcome this, all the latest Lime2-eMMC boards are
populated with 16MB SPI flash and therefore enable support
for SPI SPL boot.
For now, SPI flash can be managed using sunxi-fel's spiflash tools.
Signed-off-by: Priit Laes <priit.laes@paf.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
|
|
Update the spring settings to use this codec, which is what it actually
shipped with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_TYPES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The option OF_EMBED is deprecated,
so we switch to CONFIG_OF_SEPARATE
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
The name of the board is bcm968580xref,
so rename the config to bcm968580xref too.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
The second loader stages may be stored on GPT partitions,
enable support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable watchdog and reboot with watchdog in the configuration.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
The TPS62517 PMIC driver has been partially converted to DM, so the
legacy I2C access layer isn't needed anymore.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Add support of clk dump command and
display information during probe (under CONFIG_DISPLAY_CPUINFO).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add a new defconfig file for the AM57xx High Security EVM. This config
is specific for the case of USB/UART booting.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
