summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2016-07-22usb: Kconfig: Add Kconfigs entry USB_EHCI_ZYNQSiva Durga Prasad Paladugu
Add Kconfig entry config option for USB_EHCI_ZYNQ and update the same to enable for all zynq boards which supports USB Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-07-22ARM64: zynqmp: Enable SPL for all zynqmp boardsMichal Simek
Compile SPL for all boards even psu_init.c/h files are not in the tree yet. But this change enables covering SPL issues in mainline. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-07-22ARM64: zynqmp: Enable CLK and SPL_CLK by defaultMichal Simek
Serial driver starts to use clk framework that's why enable it by default. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-07-22ARM: zynq/zynqmp: Use the default CONFIG_BOOTDELAY=2Michal Simek
Based on: "ARM: uniphier: use the default CONFIG_BOOTDELAY=2" (sha1: 7c8ef0feb97586d35b0296b48903daef8c06ab21) "I do not insist on CONFIG_BOOTDELAY=3. The default value in Kconfig, CONFIG_BOOTDELAY=2, is just fine for these boards." Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-07-15Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-07-15sunxi: Add defconfig and dts file for the Orange Pi Lite SBCHans de Goede
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM, micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector, sdio attached rtl8189ftv wifi and an ir receiver. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-15sunxi: orangepi_pc: Add support for eMMC found on the Orange Pi PC PlusHans de Goede
The Plus variant of the Orange Pi PC has an eMMC, add support for this. Note we are using the same u-boot defconfig / dts for both the regular Orange Pi PC as well as the Orange Pi PC Plus. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-15Merge git://git.denx.de/u-boot-dmTom Rini
2016-07-15net: Add EMAC driver for H3/A83T/A64 SoCs.Amit Singh Tomar
This patch add EMAC driver support for H3/A83T/A64 SoCs. Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY). BIG Thanks to Andre for providing some of the DT code. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-14rockchip: Use of-platdata for firefly-rk3288Simon Glass
As an experiment, move this board over to use of-platdata. This means that its SPL configuration will come from C structures generated at build-time from the device tree, instead of coming from the device tree at run-time. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14dm: sandbox: Enable of-platdata for sandbox_splSimon Glass
Enable this feature so that we can use it for testing in sandbox_spl. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14sandbox: Add a new sandbox_spl boardSimon Glass
It is useful to be able to build SPL for sandbox. It provides additional build coverage and allows SPL features to be tested in sandbox. However it does not need worthwhile to always create an SPL build. It nearly doubles the build time and the feature is (so far) seldom used. So for now, create a separate build target for sandbox SPL. This allows experimentation with this new feature without impacting existing workflows. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14configs: da850evm: enable bootz commandSekhar Nori
Enable bootz command on Texas Instruments DA850 EVM board. This helps it boot zImage with device-tree blob passed. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Kevin Hilman <khilman@baylibre.com>
2016-07-14arm: am4x: add U-Boot FIT signing and SPL image post-processingMadan Srinivas
Modify the SPL build procedure for AM437x high-security (HS) device variants to create a secure u-boot_HS.img FIT blob that contains U-Boot and DTB artifacts signed (and optionally encrypted) with a TI-specific process based on the CONFIG_TI_SECURE_DEVICE config option and the externally-provided image signing tool. Also populate the corresponding FIT image post processing call to be performed during SPL runtime. Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14arm: omap5: add U-Boot FIT signing and SPL image post-processingAndreas Dannenberg
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS) device variants to create a secure u-boot_HS.img FIT blob that contains U-Boot and DTB artifacts signed with a TI-specific process based on the CONFIG_TI_SECURE_DEVICE config option and the externally-provided image signing tool. Also populate the corresponding FIT image post processing call to be performed during SPL runtime. Signed-off-by: Daniel Allred <d-allred@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-12Merge branch 'master' of git://git.denx.de/u-boot-x86Tom Rini
2016-07-12x86: Add Advantech SOM-DB5800/SOM-6867 supportGeorge McCollister
Add support for Advantech SOM-DB5800 with the SOM-6867 installed. This is very similar to conga-qeval20-qa3-e3845 in that there is a reference carrier board (SOM-DB5800) with a Baytrail based SoM (SOM-6867) installed. Currently supported: - 2x UART (From ITE EC on SOM-6867) routed to COM3/4 connectors on SOM-DB5800. - 4x USB 2.0 (EHCI) - Video - SATA - Ethernet - PCIe - Realtek ALC892 HD Audio Pad configuration for HDA_RSTB, HDA_SYNC, HDA_CLK, HDA_SDO HDA_SDI0 is set in DT to enable HD Audio codec. Pin defaults for codec pin complexs are not changed. Not supported: - Winbond Super I/O (Must be disabled with jumpers on SOM-DB8500) - USB 3.0 (XHCI) - TPM Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-07-12x86: conga-qeval20-qa3: Add support for internal UARTStefan Roese
This patch adds support to enable and use the internal BayTrail UART instead of the one integrated in the Super IO Winbond chip. For this, a 2nd defconfig file is added. This is useful for tests done for the congatec SoM used on baseboards without such a Super IO chip. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-12x86: baytrail: Introduce a Kconfig option for the internal UARTBin Meng
There are quite a number of BayTrail boards that uses an external SuperIO chipset to provide the legacy UART. For such cases, it's better to have a Kconfig option to enable the internal UART. So far BayleyBay and MinnowMax boards are using internal UART as the U-Boot console, enable this on these two boards. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-11Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2016-07-11dm: mmc: Move dragonboard410c to use CONFIG_BLK and CONFIG_DM_MMC_OPSSimon Glass
Update this board to use driver model for block devices and MMC operations. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-11dm: sandbox: Convert to use CONFIG_CMD_MMC_OPSSimon Glass
Update the sandbox MMC emulation to use driver model for MMC operations. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-09defconfig: k2g_evm_defconfig: Enable Cadence QSPI controllerVignesh R
Enable Cadence QSPI controller support to use QSPI on K2G SoC. Also enable Spansion flash support to access s25fl512s flash present on K2G QSPI bus. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2g_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2G SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2l_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2L SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2e_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2E SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2hk_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2HK SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-05video: tegra: Move to using simple-panel and pwm-backlightSimon Glass
We have standard drivers for panels and backlights which can do most of the work for us. Move the tegra20 LCD driver over to use those instead of custom code. This patch includes device tree changes for the nvidia boards. I have only been able to test seaboard. If this patch is applied, these boards will also need to be synced with the kernel, and updated to use display-timings: - colibri - medcom-wide - paz00 - tec Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-02sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)Quentin Schulz
The Parrot Board is an evaluation board with an Allwinner R16 (assumed to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2 controllable buttons, an LVDS port with separated backlight and capacitive touch panel ports, an audio/microphone jack, a camera CSI port, 2 sets of 22 GPIOs and an accelerometer. The DTS file is identical to the one submitted to the upstream kernel. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-01autoboot: remove CONFIG_ZERO_BOOTDELAY_CHECKMasahiro Yamada
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2 means the autoboot with no delay, with no abort check even if CONFIG_ZERO_BOOTDELAY_CHECK is defined. To sum up, the autoboot behaves as follows: [1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y autoboot with no delay, but you can abort it by key input [2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n autoboot with no delay, with no check for abort [3] CONFIG_BOOTDELAY=-1 disable autoboot [4] CONFIG_BOOTDELAY=-2 autoboot with no delay, with no check for abort As you notice, [2] and [4] come to the same result, which means we do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the cases only by CONFIG_BOOTDELAY, like this: [1] CONFIG_BOOTDELAY=0 autoboot with no delay, but you can abort it by key input [2] CONFIG_BOOTDELAY=-1 disable autoboot [3] CONFIG_BOOTDELAY=-2 autoboot with no delay, with no check for abort This commit converts the logic as follow: CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n --> CONFIG_BOOTDELAY=-2 Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Heiko Schocher <hs@denx.de> Acked-by: Christian Riesch <christian.riesch@omicronenergy.com> Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2016-07-01ARM: socfpga: move CONFIG_BOOTDELAY to Kconfig for IS1 boardMasahiro Yamada
This recently added board missed the tree-wide migration of CONFIG_BOOTDELAY. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Pavel Machek <pavel@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-01ARM: AM437x: Align HS device variant defconfig filenameAndreas Dannenberg
Align the name of the defconfig file for high-security (HS) device variants from the AM43xx family of SoCs with the corresponding name used for the general purpose devices. This allows for easier cross-association of those files and also provides room to grow from an HS device part number perspective. Furthermore, update and cleanup associated MAINTAINERS file. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Madan Srinivas <madans@ti.com>
2016-06-28configs: Re-sync after boot menu changesTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-26arm: at91: taurus/axm: add DM and DTS supportHeiko Schocher
add DM and DTS support for the at91 based siemens boards. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> [rebased on current ToT] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26arm: at91: smartweb: add DM and DTS supportHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> [rebased on current ToT] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26corvus DTS / DM supportHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> [rebase on current ToT, don't delete gurnard DTB creation] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-24board/BuR: rename kwb board to brxre1Hannes Schmelzer
Rename B&R kwb board to brxre1 Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-24board/BuR: rename tseries board to brppt1Hannes Schmelzer
Rename B&R tseries board to brppt1 Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-24arm: bcm235xx: implement the boot0 hook codeSteve Rae
Choose the Kconfig boot0 hook option and implement the required code. Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-24arm: bcm235xx: choose 8-bit phy bus widthSteve Rae
The Kona PHY supports an 8-bit wide UTMI interface, therefore, choose this Kconfig setting. Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-24Move CONFIG_SYS_HUSH_PARSER to Kconfig for last 4 boardsMasahiro Yamada
I still see some defines of this config in board headers. Move them to defconfigs (+ renaming to CONFIG_HUSH_PARSER) to complete this migration. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-20sunxi: Add defconfig and dts file for inet86dz boardHans de Goede
The inet86dz board is a board used in 7" tablets from various oems. These tablets are a23 based 7" tablets featuring a 1024x600 LCD, 512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector which doubles as charging port. The dts file this commit adds is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20sunxi: Add defconfig and dts file for Polaroid MID2407PXE03 tabletHans de Goede
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0 PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680 touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector which doubles as charging port. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20autoboot: add CONFIG_AUTOBOOT to allow to not compile autoboot.cMasahiro Yamada
Since commit bb597c0eeb7e ("common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option"), CONFIG_BOOTDELAY is defined for all boards. Prior to that commit, it was allowed to unset CONFIG_BOOTDELAY to not compile common/autoboot.c, as described in common/Makefile: # This option is not just y/n - it can have a numeric value ifdef CONFIG_BOOTDELAY obj-y += autoboot.o endif It was a bit odd to enable/disable code with an integer type option, but it was how this option worked before that commit, and several boards actually unset it to opt out of the autoboot feature. This commit adds a new bool option, CONFIG_AUTOBOOT, and makes CONFIG_BOOTDELAY depend on it. I chose "default y" for this option because most boards use the autoboot. I added "# CONFIG_AUTOBOOT is not set" for the boards that had not set CONFIG_BOOTDELAY prior to the bad commit. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-20Merge git://git.denx.de/u-boot-dmTom Rini
2016-06-19reset: implement a reset testStephen Warren
This adds a sandbox reset implementation (provider), a test client device, instantiates them both from Sandbox's DT, and adds a DM test that excercises everything. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-06-20ARM: uniphier: use the default CONFIG_BOOTDELAY=2Masahiro Yamada
I do not insist on CONFIG_BOOTDELAY=3. The default value in Kconfig, CONFIG_BOOTDELAY=2, is just fine for these boards. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-18Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2016-06-18Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
2016-06-17arm, am335x: siemens: enable DM/DTS supportHeiko Schocher
enable basic DM/DTS support for the siemens am335x based boards. Signed-off-by: Heiko Schocher <hs@denx.de>
generated by cgit (git 2.34.1) at 2024-12-26 20:53:41 +0000