summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2016-12-16imx6: icorem6_rqs: Add FEC supportJagan Teki
Add FEC support for Engicam i.CoreM6 RQS modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16imx6: geam6ul: Add FEC supportJagan Teki
Add FEC support for Engicam GEAM6UL module. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16imx6: icorem6_rqs: Add I2C supportJagan Teki
Add I2C support for Engicam i.CoreM6 RQS modules. icorem6qdl-rqs> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl-rqs> i2c dev 0 Setting bus to 0 icorem6qdl-rqs> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl-rqs> i2c probe Valid chip addresses: 4F icorem6qdl-rqs> i2c md 4F 0xff 00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ icorem6qdl-rqs> i2c bus Bus 0: i2c@021a0000 (active 0) 4f: generic_4f, offset len 1, flags 0 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16imx6: icorem6: Rename engicam icorem6 defconfig filesJagan Teki
Rename defconfig files for better compatible with respective board names and dts files. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial supportJagan Teki
Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530) CPU: Freescale i.MX6DL rev1.3 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial supportJagan Teki
Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16imx6: geam6ul: Add NAND supportJagan Teki
Add NAND support for Engicam GEAM6UL board. Boot Log: -------- U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28) Trying to boot from NAND NAND : 256 MiB U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100) CPU: Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 42C Reset cause: WDOG Model: Engicam GEAM6UL DRAM: 128 MiB NAND: 256 MiB MMC: FSL_SDHC: 0 * Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16imx6: geam6ul: Add I2C supportJagan Teki
Add I2C support for Engicam GEAM6UL module. geam6ul> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 geam6ul> i2c dev 0 Setting bus to 0 geam6ul> i2c dev Current bus is 0 geam6ul> i2c speed 100000 Setting bus speed to 100000 Hz geam6ul> i2c probe Valid chip addresses: 2C geam6ul> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial supportJagan Teki
Boot Log: -------- U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30) Trying to boot from MMC1 U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Engicam GEAM6UL DRAM: 128 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 geam6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16imx6: icorem6: Add I2C supportJagan Teki
Add I2C support for Engicam i.CoreM6 qdl board. icorem6qdl> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl> i2c dev 2 Setting bus to 2 icorem6qdl> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl> i2c probe Valid chip addresses: 2C icorem6qdl> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Heiko Schocher <hs@denx.de>
2016-12-16imx6: icorem6: Add framebuffer supportJagan Teki
Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board. Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16icorem6: Use CONFIG_DM_ETH supportJagan Teki
Use CONFIG_DM_ETH and remove board_eth_init code from board files. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16arm: imx: add i.MX53 Beckhoff CX9020 Embedded PCPatrick Bruenn
Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2016-12-16imx: mx6sllevk: add plugin supportPeng Fan
Add plugin support for mx6sllevk board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-12-16arm: imx: add i.MX6SLL EVK board supportPeng Fan
Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-12-16board/liteboard: Add support for liteBoardMarcin Niestroj
liteBoard is a development board which uses liteSOM as its base. Hardware specification: * liteSOM (i.MX6UL, DRAM, eMMC) * Ethernet PHY (id 0) * USB host (usb_otg1) * MicroSD slot (uSDHC1) Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2016-12-16udoo_neo: Add Ethernet supportBreno Lima
UDOO Neo boards has one FEC port connected to KSZ8091, add support for it. Tested on a UDOO Neo Full with "dhcp zImage" command. Signed-off-by: Breno Lima <breno.lima@nxp.com>
2016-12-16udoo_neo: Move MX6SX configuration to KconfigBreno Lima
It's not necessary to define the processor in the defconfig file. The preferred method to select the SoC is via Kconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16arm: imx: initial support for colibri imx6Max Krummenacher
This adds board support for the Toradex module family Colibri iMX6. The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both with a version for commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16arm: imx: initial support for apalis imx6Max Krummenacher
This adds board support for the Toradex module family Apalis iMX6. The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-12Merge git://www.denx.de/git/u-boot-marvellTom Rini
2016-12-12Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2016-12-12arm64: mvebu: Enable hush parser in A8K default configurationKonstantin Porotchkin
Enable hush parser in Armada-7040 and Armada-8040 DB default configurations. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12arm64: mvebu: Enable PCIe support in Armada-7040 configurationKonstantin Porotchkin
Enable PCIe bus support in Armada-7040 DB default configuration Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12arm64: mvebu: Enable pin control support in A8K default configKonstantin Porotchkin
Enable mvebu pin control support in the default configuration files for Armada-7040 and Armada-8040 development boards Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12arm64: mvebu: Enable BUBT command support in A8K default configKonstantin Porotchkin
Enable mvebu "bubt" command support in the default configuration file for Armada-7040 and Armada-8040 development boards Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-10ARM: uniphier: disable CONFIG_ARCH_FIXUP_FDT_MEMORYMasahiro Yamada
Do not overwrite the memory nodes in the kernel DT where some parts of the memory region might be carved out. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-09davinci: omapl138_lcdk: boot from zImageFabien Parent
Stop booting legacy uImage and now boot zImage. Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09defconfigs: am57xx_hs_evm: Add default OPTEE load addressAndrew F. Davis
Currently we let U-Boot find a spot at the end of DRAM at runtime, this forces us to build an OPTEE image based on the size of DRAM for an EVM. Add a default address that works across all current AM57xx EVMs. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09defconfigs: dra7xx_hs_evm: Add default OPTEE load addressAndrew F. Davis
Currently we let U-Boot find a spot at the end of DRAM at runtime, this forces us to build an OPTEE image based on the size of DRAM for an EVM. Add a default address that works across all current DRA7xx EVMs. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09configs: omap5_uevm_defconfig: Enable LPAE modeKeerthy
Enable Linear Physical Address Extension mode which is a prerequisite for hypervisor mode. Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09Revert "Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze"Tom Rini
This reverts commit 3edc0c252257e4afed163a3a74aba24a5509b198, reversing changes made to bb135a0180c31fbd7456021fb9700b49bba7f533.
2016-12-09Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-12-08travis-ci: Add zynq_zc702 target supportMichal Simek
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Use embded option because of qemu Use my repo till Stephen merge it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-12-08block: Move ceva driver to DMMichal Simek
This patch also includes ARM64 zynqmp changes: - Remove platform non DM initialization - Remove hardcoded sata base address Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Series-to: sjg, agraf@suse.de Series-cc: uboot Series-version: 4 Series-changes: 2 - make ceva_init_sata static - Move SATA_CEVA to defconfig - Initalized max_lun and max_id platdata Series-changes: 3 - Extend Kconfig help description - sort dm.h - Remove SPL undefinition from board file - Fix Kconfig dependecies
2016-12-06socfpga: add support for Terasic DE1-SoC boardAnatolij Gustschin
Add CycloneV based Terasic DE1-SoC board. The board boots from SD/MMC. Ethernet and USB host is supported. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Marek Vasut <marex@denx.de>
2016-12-05Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-12-05armv8: QSPI: Add AHB bus 16MB+ size supportYuan Yao
The default configuration for QSPI AHB bus can't support 16MB+. But some flash on NXP layerscape board are more than 16MB. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-12-05Merge git://www.denx.de/git/u-boot-i2cTom Rini
2016-12-05arm64: mvebu: Add PCI support to DB-88F8040 boardStefan Roese
This patch adds PCI support to the Marvell Armada-8K devel board. Additionally the Intel E1000 ethernet driver is enabled so that network support is available on this board, even without the internal network interfaces being supported (yet). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com>
2016-12-05arm64: mvebu: Add support for the DB-88F8040 Armada 8k devel boardStefan Roese
This patch adds the necessary files to support the Marvell Armada 8k devel board. Most board specfic files are shared with the Armada 7k boards under the name "armada-8k*". So only minimal changes are necessary to add this basic board support (except the DT files of course). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com>
2016-12-05arm64: mvebu: Rename db-88f7040 files to armada-8kStefan Roese
This moves some of the Armada DB-88F7040 board specific files to a more generic name: armada-8k. This is in preparation for the Armada-8k support which will be added soon. And since both platforms share most devices, lets also share most source files to not duplicate the code here. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com>
2016-12-05arm: exynos: i2c: Convert exynos boards to use DM_I2CSimon Glass
Three boards are still not converting to use DM_I2C. They are also using the old PMIC framework. Rather than removing them, add #ifdefs to allow them to continue to build. This will give the maintainers a little more time to decide whether to convert them or not. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de>
2016-12-04Merge git://git.denx.de/u-boot-mpc85xxTom Rini
2016-12-04defconfig: am43xx_evm: Enable DM_SPI and DM_SPI_FLASHVignesh R
Commit 4c4e3b37750f3("ARM: AM43xx: Enable FIT") accidentally disabled DM_SPI and DM_SPI_FLASH. Add back DM_SPI and DM_SPI_FLASH to am43xx_evm_defconfig in order to make use of DM framework for QSPI. Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-12-04arm: Remove VCMA9 boardSimon Glass
This board has not been converted to DM_SERIAL by the deadline. Remove it. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: David Müller <d.mueller@elsoft.ch> Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-04arm: Remove smdk2410 boardSimon Glass
This board has not been converted to DM_SERIAL by the deadline. Remove it. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: David Müller <d.mueller@elsoft.ch>
2016-12-04ARM: dts: AM571x-IDK Initial SupportSchuyler Patton
Add initial DTS support for AM571-IDK evm. Signed-off-by: Schuyler Patton <spatton@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04board: ti: am57xx: Add support for detection of X15 revb1Lokesh Vutla
BeagleBoard-X15 Rev B1 with SR1.1 platform have incompatible changes for HDMI GPIO requiring new dtb support. This implies we have to properly identify the platform now as well. Hence provide a different board name for the Rev B1 variants. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04configs: dra7xx: Enable lp873x optionsKeerthy
DRA71-evm uses LP873x regulator. Enable lp873x PMIC config options. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2025-01-12 14:00:41 +0000