summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2020-07-26configs: sandbox: Enable sub command 'env info'Patrick Delaunay
Enable support for sub command 'env info' in sandbox with CONFIG_CMD_NVEDIT_INFO. This is aimed primarily at adding unit test. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-25configs: j721e_evm: Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3Dave Gerlach
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC driver can be used for SoC detection. Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-25configs: am65x_evm: Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3Dave Gerlach
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC driver can be used for SoC detection. Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-25test: Add tests for SOC uclassDave Gerlach
Add a sandbox SOC driver, and some tests for the SOC uclass. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-25ARM: rmobile: Add Beacon EmbeddedWorks RZG2M Dev KitAdam Ford
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also known as the RZ/G2M. The kit consists of a SOM + Baseboard and supports microSD, eMMC, Ethernet, a couple celular radios, two CAN interfaces, Bluetooth and WiFi. Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-25net: dc2114x: Add Kconfig entriesMarek Vasut
Add Kconfig entries for the dc2114x driver and convert various boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Ramon Fried <rfried.dev@gmail.com>
2020-07-24Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Fix SiFive HiFive Unleashed board booting failure problem. - Enable SiFive fu540 PWM driver. - Support SiFive fu540: SPI boot. - Update OpenSBI used for RISC-V CI testing. - Revert "riscv: Allow use of reset drivers". - Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"". - sysreset: syscon: - Don't assume default value for offset and mask property. - Support value property. - qemu: Add syscon reboot and poweroff support. - Fix SIFIVE debug serial dependency. - Fix linking error when building u-boot-spl with no SMP support. - AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg. - Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi - SiFive fu540 avoid using hardcoded ram base and size.
2020-07-24Revert "Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dm"Tom Rini
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing changes made to 56d37f1c564107e27d873181d838571b7d7860e7. Unfortunately this is causing CI failures: https://travis-ci.org/github/trini/u-boot/jobs/711313649 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-24sifive: fu540: Add Booting from SPIJagan Teki
Add booting from SPI for SiFive Unleashed board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bin.meng@windriver.com> Tested-by: Bin Meng <bin.meng@windriver.com>
2020-07-23Merge tag 'dm-pull-20jul20' of git://git.denx.de/u-boot-dmTom Rini
binman support for FIT new UCLASS_SOC patman switch 'test' command minor fdt fixes patman usability improvements
2020-07-22Merge tag 'u-boot-rockchip-20200722' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - New rk3326 board: Hardkernel Odroid Go2; - Update board config and dts for RockPI 4/N8/N10; - Update led boot on support for roc-rk3399-pc; - Enable SPI Flash suppor for rk3328 rock64 board; - Update rockchip pcie phy to use generic framework;
2020-07-22rockchip: rock-p-n8/n10: Disable RAM_ROCKCHIP_DEBUGJagan Teki
Disable ram rockchip debug driver for ROCKPi N8/N10 boards since we have verified ram in many instances with respective U-Boot versions. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-n10: Enable PCI/NVMEJagan Teki
Enable PCI/NVME for M.2 Slot on RockPI-4 boards. => nvme info Device 0: Vendor: 0x144d Rev: 4L1QCXB7 Prod: S35FNX0J623292 Type: Hard Disk Capacity: 122104.3 MB = 119.2 GB (250069680 x 512) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-n8: Enable on board devicesSuniel Mahesh
Enable common on board devices for ROCKPi N8. - USB 2.0 Host - USB 2.0 OTG/Gadget - HDMI Out Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-n10: Enable on board devicesSuniel Mahesh
Enable common on board devices for ROCKPi N10. - USB 2.0 Host - USB 3.0 Host - USB 3.0 Gadget - HDMI Out Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Set LED only during POR and pwr_key=yJagan Teki
ROC-RK3399-PC has specific set of configurations for on-board led setup. Due to easiness for user to know the state of the board roc-rk339-pc board code will setup the low power led on/off, and waiting for user to press power key and then glow full power led. All this needs to happen only during power-on-reset not for soft reset or WDT. Also, it is not a proper usage to ask the user to press the Power key if the board connected remotely, so add the environment variable 'pwr_key' to check as well. So, user need to press Power key only - during POR - pwr_key=y Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Add custom led_setup()Jagan Teki
roc-rk3399-pc has some specific requirements to support LEDS, environment. board detection and etc prior to U-Boot proper. So as of now SPL would be a better stage for these custom board requirements to support unlike TPL. Adding few of these custom requirements like LEDS in TPL would require extra code pulling and also the size of TPL can grow. So, this patch moves the leds code from TPL into SPL Board init led_setup code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> (split tpl.c change as separate patch) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22arm64: dts: rockchip: Add Radxa ROCK Pi 4C supportJagan Teki
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled GPIO pin change compared to 4B, 4C. So, add or enable difference nodes/properties in 4C dts by including common dtsi. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22arm64: dts: rockchip: Add ROCKPi 4A/4B supportJagan Teki
Rock PI 4 has 3 variants of hardware platforms called RockPI 4A, 4B, and 4C. - Rock PI 4A has no Wif/BT. - Rock PI 4B has AP6256 Wifi/BT, PoE. - Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable GPIO pin change compared to 4B, 4C So move common nodes, properties into dtsi file and include on respective variant dts files. Use 4B dts into default rock-pi-4 defconfig until we find any solution for dynamic detection of these variants. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: firefly-rk3399: enable CONFIG_USB_DWC3Kever Yang
To fix below build error: drivers/usb/host/built-in.o: In function `xhci_dwc3_remove': drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy' drivers/usb/host/built-in.o: In function `xhci_dwc3_probe': drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy' Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Disable RAM_ROCKCHIP_DEBUGJagan Teki
Disable ram rockchip debug driver for roc-rk3399-pc boards since we have verified ram in many instances with respective U-Boot versions. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock64-rk3328_defconfig: Add SPI Flash supportJohannes Krottmayer
Add U-Boot SPI Flash support for the PINE64 Rock64 board Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Update ENV offset, sizeJagan Teki
Adjust the ENV offset, size to fit into all images on 16MB flash. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: roc-rk3399-pc: Enable USB GadgetJagan Teki
Enable DWC3 core, gadget for roc-rk3399-pc board. This would help to use fastboot by default. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable HDMI outputJagan Teki
Enable config options to get HDMI output on RockPI-4 boards. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable USB GadgetJagan Teki
Enable USB gadget for rock-pi-4 boards. This would help to use fastboot by default. Note: Connect the Host USB cable (Port A or C) to rock-pi-4 Upper USB 3.0 port. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable PCI/NVMEJagan Teki
Enable PCI/NVME for M.2 Slot on RockPI-4 boards. => nvme info Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Cc: Tom Cubie <tom@radxa.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rock-pi-4: Enable USB3 HostJagan Teki
Enable USB3.0 Host support for RockPI-4 boards. Note that the Upper USB3.0 port is marked as otg and lower USB3.0 port marked as host, so this below log capture when USB3.0 mass storage plug in at lower USB 3.0 port. Log: Bus usb@fe380000: USB EHCI 1.00 Bus usb@fe3c0000: USB EHCI 1.00 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... cannot reset port 1!? 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found => usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (5 Gb/s, 0mA) U-Boot XHCI Host Controller 1 Hub (5 Gb/s, 0mA) | U-Boot XHCI Host Controller | +-2 Mass Storage (5 Gb/s, 224mA) SanDisk Dual Drive 040130e3ee554b7078843f4eb331646 Cc: Tom Cubie <tom@radxa.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: rockpro64: Enable USB3.0 HostJagan Teki
Enable USB3.0 Host support for RockPro64 boards. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22rockchip: board: add Hardkernel Odroid Go2 boardHeiko Stuebner
Also known as Odroid Go Advance but named Go2 internally by the vendor it seems. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-20configs: j721e_evm: Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3Dave Gerlach
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC driver can be used for SoC detection. Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-20configs: am65x_evm: Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3Dave Gerlach
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC driver can be used for SoC detection. Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-20test: Add tests for SOC uclassDave Gerlach
Add a sandbox SOC driver, and some tests for the SOC uclass. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-18mips: octeon: Add minimal Octeon 3 EBB7304 EVK supportStefan Roese
This patch adds very basic minimal support for the Marvell Octeon 3 CN73xx based EBB7304 EVK. Please note that the basic Octeon port does not support DDR3/4 initialization yet. To still use U-Boot on with this port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot to the prompt on this board. Supported devices: - UART - reset - CFI parallel NOR flash Signed-off-by: Stefan Roese <sr@denx.de>
2020-07-17Convert CONFIG_MXC_UART to KconfigTom Rini
This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-07-17Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- New timer API to allow delays with a 32-bit microsecond timer - Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core - x86: Enable ACPI table generation by default - x86: Enable the copy framebuffer on Coral - x86: A few fixes to FSP2 with ApolloLake - x86: Drop setup_pcat_compatibility() - x86: Primary-to-Sideband Bus minor fixes
2020-07-17Merge tag 'u-boot-imx-20200716' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx i.MX for 2020.10 ---------------- - i.MX DDR driver fix/update for i.MX8M - i.MX pinctrl driver fix. - Use arm_smccc_smc to remove imx sip function - i.MX8M clk update - support booting aarch32 kernel on aarch64 hardware - fused part support for i.MX8MP - imx6: pcm058 to DM Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
2020-07-17sound: Add an ACPI driver for Maxim MAX98357acSimon Glass
This chip is used on coral and we need to generate ACPI tables for sound to make it work. Add a driver that does just this (i.e. at present does not actually support playing sound). Signed-off-by: Simon Glass <sjg@chromium.org> [bmeng: Use the correct acpi_irq_polarity enum number] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-07-17sound: Add an ACPI driver for Dialog Semicondutor da7219Simon Glass
This chip is used on coral and we need to generate ACPI tables for sound to make it work. Add a driver that does just this (i.e. at present does not actually support playing sound). Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-17acpi: mmc: Generate ACPI info for the PCI SD CardSimon Glass
Write required information into the SSDT to describe the SD card card-detect pin. Since the required GPIO properties are not present in the device-tree binding, set them manually for now. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-07-17coral: Enable the copy framebufferSimon Glass
Enable this feature on chromebook_coral to speed up the display. With this change, the time taken to print the environment to the display without CONFIG_CONSOLE_SCROLL_LINES is reduced from 1830ms to 62ms. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-07-16mx6memcal: fix buildStefano Babic
Commit 4503299 has a side effect on this board, and build is broken. Adjust mx6memcal_defconfig to build it again. Signed-off-by: Stefano Babic <sbabic@denx.de>
2020-07-16cmd: fix lsblk commandHeinrich Schuchardt
Add missing includes. Add CMD_LSBLK to sandbox_defconfig. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-16imx6: Remove unneeded CONFIG_DM_MDIOFabio Estevam
As explained in the CONFIG_DM_MDIO text inside drivers/net/Kconfig: "Useful in particular for systems that support DM_ETH and have a stand-alone MDIO hardware block shared by multiple Ethernet interfaces." i.MX6 has a single FEC instance, so there is no need to select CONFIG_DM_MDIO. Remove it from the i.MX6 defconfig files. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-07-16arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)Lukasz Majewski
This commit enables imx28 based XEA board's u-boot.sb (SPL) to download u-boot proper (u-boot.img) via Ymodem protocol. This is extremely useful in the recovery scenario where u-boot.sb is downloaded via uuu utility to SDRAM [*], and then one can upload u-boot proper via serial console to fully debrick the device. Note - debricking procedure of imx28 devices: - NXP's original USB based tools (like mxsldr or uuu) expect single u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and U-Boot proper distinction. [*] On Host: ------------ cat << EOF > imx28_xea.lst uuu_version 1.3.0 SDPS: boot -f /srv/tftp/xea/u-boot.sb SDPU: done EOF Please start picocom: sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1 sudo ./uuu/uuu -V imx28_xea.lst On the U-boot console one shall see: Trying to boot from UART CCC Then please press CTRL+A, S and type u-boot.img Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-07-16imx6: aristainetos: sync defconfig with 2020.10Heiko Schocher
as patch gpio: search for gpio label if gpio is not found through bank name is now in mainline, but functionality is disabled, we need to enable CONFIG_DM_GPIO_LOOKUP_LABEL for the aristainetos boards. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-07-14arm: imx6q: pcm058: Convert pcm058 to use DM with DTsNiel Fourie
Convert pcm058 support to use device trees and the driver model. Add rudimentary boot scripts to the environment, expand README. Signed-off-by: Niel Fourie <lusus@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2020-07-14imx8m: Refactor the OPTEE memory removalPeng Fan
Current codes assume the OPTEE address is at the end of first DRAM bank. Adjust the process to allow OPTEE in the middle of first bank. When OPTEE memory is removed from first bank, it may split the first bank to two banks, adjust the MMU table for the split case, Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge i.MX8MP evk to default to avoid issue. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com> Tested-by: Silvano di Ninno <silvano.dininno@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-13omap3_beagle: Finish current outstanding DM migrationsTom Rini
At this point in time we can now remove our legacy code and switch to enabling DM for USB and Ethernet. Cc: Derald D. Woods <woods.technical@gmail.com> Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2020-07-13ARM: da850-evm: Unify config options with KconfigAdam Ford
There are two options that are currently whitelisted, but they are redundant, because there are not necessary since Kconfig options exist to basically state the same thing. CONFIG_DIRECT_NOR_BOOT and CONFIG_USE_NOR are both set together and only used by the da850 when booting from NOR, however the only time CONFIG_MTD_NOR_FLASH is configured is when booting from NOR. Since NOR doesn't need SPL, the options for SPL can be moved to a check for building SPL instead of checking for NOR. This patch removes the checks for these two config options and unifies the checks around the Kconfig option of CONFIG_MTD_NOR_FLASH. Since this board is the only board that uses these two config options, they can be removed from the whitelist table. Signed-off-by: Adam Ford <aford173@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-09 17:00:14 +0000