| Age | Commit message (Collapse) | Author |
|---|
|
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Migrate to using device tree required for further driver model
integration.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Enbale FIT image, GPT command, i.MX thermal and EFI loader support.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Move console in env from header file to defconfig.
While at it also update copyright year and remove spurious comments and
new lines.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Use distro defaults and minimise default configuration again using
savedefconfig.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add board-specific FDT function to store U-Boot version in device tree.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Use MMC device model, and remove USDHC pin configuration code since the
pinctrl driver is used.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Add simplified, generalised, ppd device tree and enable CONFIG_DM.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Use SPI flash device model, and remove SPI pin configuration code since
the pinctrl driver is used.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Enable CONFIG_DM_GPIO as a pre-requisite for enabling CONFIG_DM_SPI.
Add explicit gpio_requests.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Use MMC device model, and remove USDHC pin configuration code since the
pinctrl driver is used.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Add simplified, generalised, bx50v3 device tree and enable CONFIG_DM.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
This commit updates BK4's and PCM052's config files to support as much
as possible device tree and model in u-boot.
Moreover, remove CONFIG_* from pcm052.h (as those are now in
bk4|pcm052_defconfig)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
fdtdec tests and improvements for carve-outs
pinctrl race-condition fix
various other fixes in sandbox, sound, mkimage, etc.
|
|
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
|
|
stm32 patches for v2019.07-rc1
- Add trusted boot with TF-A for stm32mp1
- stm32mp1 dts files sync'ed with Linux version
- add STM32MP1 Discovery boards (DK1 and DK2)
- add STMFX gpio expander driver
- misc improvement for stm3mp1 supports
- rename stpmu1 to stpmic1 (official name)
- stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu)
- add STM32 FMC2 NAND flash controller driver
|
|
|
|
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
|
|
This patch enables USB and file-system support on the LinkIt smart
MT7688 module for both, the normal and the RAM default config.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Update default config to use network driver for ServalT SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
|
|
Update default confing to use network driver for Jaguar2 SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
|
|
Enable the gpio support (driver and command)
in the configuration of the board bcm963158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Enable the gpio support (driver and command)
in the configuration of the board bcm968580xref.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Enable the gpio support (driver and command)
in the configuration of the board bcm968380gerg
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
|
|
The new mtd is very useful so let's enable it on the LinkIt Smart
7688 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jiri Kastner <cz172638@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Activate PINCTRL_STMFX and needed part for generic pincontrol
PINCTRL_FULL, PINCONF. Increase pre-reloc memory for MALLOC
(needed for each DM pinconfig node).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Add configuration useful for test
- FIT support
- MEMTEST
- DFU
- CACHE
- TIME
- TIMER
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
activate Fastboot for eMMC on EV1 board (mmc1)
$> sudo apt-get install android-tools-adb android-tools-fastboot
$> fastboot -i 0x0483 getvar bootloader-version
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Clearly separate bootcmd for stm32mp1 board
(bootcmd_stm32mp) and preboot management.
That solve issue for fastboot continue command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Cosmetic cleanup in mach-stm32mp Kconfig
- remove duplicated SPL_DRIVERS_MISC_SUPPORT
- update help for TARGET_STM32MP1
- set value for NR_DRAM_BANKS
- remove one comment as DEBUG_UART is deactivated by default
- include board Kconfig at the end of the file
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
|
|
Update VCI string to keep it compatible with legacy test setups.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add Support for booting from Ethernet.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Make some room in SPL by getting rid of unnecessary configs.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Enable CONFIG_OF_BOARD_SETUP so that msmc sram dt nodes
are updated correctly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Now that NAND is supported on DRA71x include various NAND environment
settings
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add NAND support to dra71x-evm defconfig
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Add support for the Bosch Guardian board.
CPU : AM335X-GP rev 2.1
Model: Bosch AM335x Guardian
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
|
|
AM57xx IDK EVMs can boot out of QSPI. Enable configs to support QSPI
boot. Also enable configs for updating QSPI boot images over DFU.
Tested on AM572x IDK EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable ti phy dp83867 for k2g
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch update the behavior introduced by
commit 96907c0fe50a ("dm: spi: Read default speed and mode values from DT")
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.
DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.
But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This board was added to u-boot first but the Linux maintainers requested
a more descriptive name. Rename the file to match the Linux usage and
update the board defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Switch from legacy IDE driver to sata_mv driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
