| Age | Commit message (Collapse) | Author |
|---|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.04
-----------------
- DM : mx6sabresd
- mx6ul_14x14_evk: fix video
- mx8qxp; fix console for booting
- sync DTS with kernel (imx6sx)
- drop obsolete woodburn (mx35)
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/660550811
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.04 cycle:
- Includes two small configuration fixes that will solve the SPL booting
on sama5d3_xplained board.
|
|
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Booting a mainline kernel in secure mode on i.MX7D causes only
one CPU to be brought up.
Change it to booting in non secure mode by default, which
allows the two CPUs to be brought up.
It does have a side effect of not probing the CAAM driver.
If CAAM driver is needed then a secure world OS such as OPTEE needs
to be used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
SPL boot cannot find dtb if CONFIG_SPL_SEPARATE_BSS is disabled :
CONFIG_SPL_SEPARATE_BSS=n
RomBOOT
<debug_uart> Missing DTB
### ERROR ### Please RESET the board ###
RomBOOT
CONFIG_SPL_SEPARATE_BSS=y
RomBOOT
<debug_uart>
U-Boot SPL 2019.04-linux4sam_6.2-icp-dirty (Feb 24 2020 - 15:34:35 +0100)
Trying to boot from NAND
<debug_uart>
Signed-off-by: Fabien Lehoussel <fabien.lehoussel@medianesysteme.com>
|
|
Enale DM_PCI support in order to avoid board removal from
the project.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Soc supports cache so let's enable it.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Board is not longer used, remove it.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
On the aristainetos2c boards the PMIC needs to be initialized,
because the Ethernet PHY uses a different regulator that is not
setup per hardware default. This does not influence the other
versions as this regulator isn't used there at all.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Enable configs to support eMMC boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
With CONFIG_SUPPORT_EMMC_BOOT moved to Kconfig, move it to defconfig
files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add initial eMMC support for Cortina Access Presidio
Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
|
|
- ABB SECU board
- Assorted minor fixes
|
|
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
This config option was present in am335x_boneblack_defconfig, but we
have to use generic am335x_evm_defconfig now, as BBB defconfig was
removed in commit 8fa7f65dd02c ("configs: Remove
am335x_boneblack_defconfig"). So this patch merely brings that option
back.
Tested on BeagleBone Black:
=> fastboot 0
$ fastboot flash rootfs rootfs.img
Fixes: 8fa7f65dd02c ("configs: Remove am335x_boneblack_defconfig")
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
|
|
DFU over TFTP flashing method might be helpful in order to speed-up the
flashing process of big images (as DFU works over USB EP0, which is
quite slow). Also, it's a good backup option in the case when USB got
broken (either in software or hardware), to avoid resorting to SD card
boot.
This config option was present in am335x_boneblack_defconfig, but we
have to use generic am335x_evm_defconfig now, as BBB defconfig was
removed in commit 8fa7f65dd02c ("configs: Remove
am335x_boneblack_defconfig"). So this patch merely brings that option
back.
Tested on BeagleBone Black:
=> setenv dfu_alt_info $dfu_alt_info_emmc
=> setenv ipaddr 192.168.0.100
=> setenv serverip 192.168.0.1
=> setenv updatefile update_uboot.itb
=> dfu tftp mmc 1
Where 'update_uboot.its' file looks like this:
/dts-v1/;
/ {
description = "Automatic U-Boot update";
#address-cells = <1>;
images {
u-boot.img.raw-1 {
description = "U-Boot binary";
data = /incbin/("u-boot.img");
compression = "none";
type = "firmware";
load = <0x60000>;
hash-1 {
algo = "sha1";
};
};
};
};
And 'update_uboot.itb' is generated as follows:
$ mkimage -f update_uboot.its update_uboot.itb
Newly flashed U-Boot works fine.
Fixes: 8fa7f65dd02c ("configs: Remove am335x_boneblack_defconfig")
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
|
|
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
|
|
Enable ESM modules for both PMIC and SoC side for proper watchdog
handling on the board.
SPL_BOARD_INIT is also enabled so that the board init function
probing the drivers is called.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Remove saving ENV in eMMC in R5 as the power domains are not
setup. Environment in eMMC cannot be read if we do not boot from
eMMC.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Enable R5F remoteproc support in R5 defconfig so that R5s can
be started in SPL. While at it enable the SPL_FS_EXT4 config
option to load the firmwares from file system.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable OSPI related configs for J721e HS variant.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable OSPI related defconfigs for AM65x HS variant.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable OSPI related defconfigs. Also enable SPL_DMA so that DMA is used
during OSPI boot
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable OSPI related defconfigs. Also enable SPL_DMA so that DMA is used
during OSPI boot
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx fixes for v2020.04-rc4
- Fix link good bit handling in dp83867
- Rename generic Zynq defconfig
- Fix zybo z7 low leve setup
- Fix error path in zynq_gem driver and fix 64bit usage
- Fix invalid clock name quieries for Versal
- Fix zynq/zynqmp SPL low level configuration via DT selection
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (3rd)
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Just cosmetic change before real switch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The board uses 100 MHz clock for UART bitrate generator,
but is configured as 50 MHz on defconfig.
This produces wrong console output.
The first message, "Debug uart enabled" is received as:
"������b"
Fix the issue by configuring the correct clock for the
UART baudrate generator
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The eMMC controller on LD20 or later supports HS-400 mode. It works on
a quick test. Enable it in case somebody may want to use it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Switch over to ADMA from SDMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This fixes the inadvertent definition of CONFIG_DTB_RESELECT and
CONFIG_MULTI_DTB_FIT in the K2x HS defconfigs, that happened as part of
a resync of the defconfigs.
The inclusion of these config options causes ethernet to stop working on
K2x HS devices as they interfere with the installation of the secure
boot monitor.
This patch also removes the above configs for the K2 GP devices, as they
are not needed, and to keep the differences between the GP and HS
defconfigs to a minimum.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
- Update Sata node for T2080QDS and revert SATA related unrequired
patches.
|
|
When the board was originally submitted, it was attempting to use the
ESDHC driver. The board uses the USDHC driver.
Signed-off-by: Carl Gelfand <carl@novtech.com>
Cc: Shawn Guo <shawn.guo@kernel.org> (maintainer:MEERKAT96 BOARD)
Acked-by: Shawn Guo <shawnguo@kernel.org>
|
|
This reverts commit 02dc1599ba0b16eb21ba0c206e5b6f38fe7b67a7
Commit 02dc1599ba0b ("configs: enable sata, eSDHC, USB device module in
T2080QDS")
has some sata defconfig changes to fit support DM mode, Now the driver
will be reverted, So revert it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
There are many boards share the board file and device header file with
rk3399 evb, add target type MACRO so that it is fixed instead of default
to the first target in "RK3399 board select".
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
|
s/dtbi/dtb/
Signed-off-by: Jared Baldridge <jrb@expunge.us>
|
|
indicate power mode
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Enable HDMI output for Tinker RK3288 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
|
|
Add mmc device partition 0 as the seat of the environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable configs to fix USB Host boot mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Early cons will be used in uart boot. Enable the same for j721e_r5
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable CONFIG_SPL_ETH_SUPPORT to fix ethernet boot support.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
