summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2020-05-14Merge tag 'u-boot-stm32-20200514' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - stm32mp1: migrate MTD and DFU configuration in Kconfig - stm32mp1: add command stm32prog - stm32mp1: several board and arch updates - stm32mp1: activate data cache in SPL and before relocation - Many improvment for AV96 board and DHCOR SoM (add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM) - clk: stm32mp1: fix CK_MPU calculation - DT alignment of stm32mp1 device tree with Linux 5.7-rc2
2020-05-14Merge tag 'rpi-next-2020.07' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi - fix phy configuration for RPi4's bcmgenet - sync RPi4's env size with other RPi configs - add kconfig option to reserver more pages in the EFI mem map - add support for SDMA which is used by RPi4 - fix corner case boot bug for RPi3 32-bit
2020-05-14ARM: stm32: Hog GPIO PF7 high on DHCOM to unlock SPI NOR nWPMarek Vasut
The SPI NOR nWP line is connected to GPIO PF7 on the SoM, pull the GPIO line high by default to clear SPI NOR WP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-14ARM: stm32: Define I2C EEPROM bus and address on DHCOMMarek Vasut
Define I2C EEPROM bus and address, so that the 'eeprom' command uses the correct ones and does not generate the following error: eeprom_rw_block: Cannot find udev for a bus 0 Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-14configs: stm32mp1: activate CONFIG_ERRNO_STRPatrick Delaunay
Add support of errno_str, used in command pmic and regulator. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14configs: stm32mp1: activate Ethernet PHY RealtekChristophe Roullier
Need Realtek driver to manage in RTL8211F the configuration of the LED. Initialize LCR (LED Control Register) to configure green LED for Link, yellow LED for Active Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-14stm32mp: stm32prog: add MTD devices supportPatrick Delaunay
Add support of MTD device (DFU_MTD backend) for NOR, NAND or SPI-NAND target. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp: stm32prog: add MMC devicePatrick Delaunay
Add support of MMC device (based on DFU_MMC backend) for SD card and eMMC update. Create a GPT partitioning on the device. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp: add the command stm32progPatrick Delaunay
Add a specific command stm32prog for STM32MP soc family witch allows to program the boot devices with the tool STM32CubeProgrammer (http://www.st.com/STM32CubeProg). This command uses the same UART STM32 protocol than MCU STM32 with or USB with DFU protocol v1.1 (ithe MCU ST extension are no supported). The executed actions are based on a tab separated value file with a stm32 header, the FlashLayout file (https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout). This file is parsed by the U-Boot command to: - initialize the devices - create the partition table on each device - initialize the DFU backend to access to not volatile memory (NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC) Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout. The communication between U-Boot and STM32CubeProgrammer is done with the specific alternate configuration (see "AN5275: USB DFU/USART protocols used in STM32MP1 Series bootloaders" for details). The command stm32prog is executed when a boot from USB is detected (selected with bootpins) and we can program the boot devices with a simple command (on Windows or Linux): PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv 1/ the ROM code loads TF-A in embedded RAM (DFU or uart) 2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart) 3/ U-Boot executes the stm32prog command (DFU or uart) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14configs: stm32mp1: remove optee defconfigPatrick Delaunay
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig is identical to stm32mp15_trusted_defconfig and can be removed. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp1: dynamically detect op-tee presencePatrick Delaunay
Activate OP-TEE driver for trusted and optee defconfig. This driver allows detection of TEE presence for boot from flash; CONFIG_STM32MP1_OPTEE is also removed. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14ARM: stm32: Implement board coding on AV96Marek Vasut
The AV96 board does exist in multiple variants. To cater for all of them, implement board code handling. There are two GPIOs which code the type of the board, read them out and use the value to pick the correct device tree from an fitImage. Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
2020-05-14ARM: stm32: Add default config for DHCORMarek Vasut
Add default U-Boot configuration for the DHCOR SoM on AV96 board. Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-05-13configs: rpi_arm64: enable SDHCI SDMA supportMatthias Brugger
RPi4 supports SDMA on it's SDHCI controller. Enable to option for the combine RPi3/4 config. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-05-12Merge tag 'u-boot-amlogic-20200511' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - Enable USB Host for Odroid-C2 board - Add Open-Drain/Open-Source emulation in GPIO uclass
2020-05-12configs: rpi_arm64: sync env size with rpi_{3,4}_defconfigMarek Szyprowski
Use the same environment size as the configs dedicated for rpi3 and rpi4. This allows to switch between the builds and not to loose the settings stored on the SD card. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-05-12configs: rpi_4 : enable SDHCI_SDMA configJaehoon Chung
Enable SDHCI_SDMA configuration. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-05-11Merge tag 'ti-v2020.07-rc2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-ti - Fix boot issues on Nokia RX-51 - Configure AM6 CPSW for 10Mbps in rgmii mode. - Minor changes for J721e
2020-05-11odroid-c2: enable USB host controllerBeniamino Galvani
Enable the second USB controller, which is connected to a hub with 4 ports. The first controller is for the OTG port and is currently not supported. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> [narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-05-11Nokia RX-51: Disable some unused features to decrease size of u-boot binaryPali Rohár
Maximal allowed size of U-Boot binary for Nokia N900 is just 262144 bytes. Signed-off-by: Pali Rohár <pali@kernel.org>
2020-05-11Nokia RX-51: Enable CONFIG_CONSOLE_MUXPali Rohár
After this change both device display and serial console would contain U-Boto output automatically without any future configuration. This would allow easier debugging on real device as access to serial console is hard and also in qemu emulator where it is easier to copy+paste from serial console as from SDL framebuffer. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-05-11Nokia RX-51: Revert back onenand defitionsPali Rohár
In commit commit 43ede0bca7fc ("Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT") were removed definitions for onenand partitions. Revert them back and enable needed options for onenand support. Signed-off-by: Pali Rohár <pali@kernel.org>
2020-05-11Nokia RX-51: Move code from defconfig back to C header filePali Rohár
In commit commit 37304aaf60bf ("Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig") was moved complicated multiline script code from C header to oneliner in defconfig. After this change multiline to wide oneliner it is hard to read this code and even harder to debug. Moreover this script code should be at place where are other scripts, so move it back to C header file. Define new env variable preboot which stores this script and in option CONFIG_PREBOOT calls this preboot variable. Signed-off-by: Pali Rohár <pali@kernel.org>
2020-05-10imx: Add support for i.MX8MM Beacon EmbeddedWorks devkit.Adam Ford
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing a devkit based on the i.MX8M Mini SoC consisting of baseboard + SOM. It supports eMMC on the SOM, microSD on the baseboard, various GPIO, the PINCTRL, and UART. Signed-off-by: Adam Ford <aford173@gmail.com>
2020-05-10imx8mq_phanbell: Run SPL with caches enabledFabio Estevam
It is safe to run SPL with caches enabled on i.MX8M, so remove such restriction. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-05-10ARM: imx: pico-imx8mq: Add support for Technexion Pico-iMX8MQMarek Vasut
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier board. Currently working is ethernet, serial, eMMC. DT is imported from Linux 5.4.28 ("462afcd6e7ea") . Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08treewide: mem: Enable MEMTEST via defconfigMichal Simek
There is no reason to enable MEMTEST from headers when was converted to Kconfig already. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-05-08configs: migrate CONFIG_SYS_MTDPARTS_RUNTIME to defconfigsPatrick Delaunay
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-08configs: migrate CONFIG_SET_DFU_ALT_INFO to defconfigsPatrick Delaunay
Move CONFIG_SET_DFU_ALT_INFO into Kconfig done by moveconfig.py. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-05-08configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-07arm: juno: enable USBAndre Przywara
The Juno board features a standard compliant EHCI/OHCI USB host controller pair, which we can just enable. The platform data is taken from the device tree. This allows to use USB mass storage (the only storage on a Juno r0) for loading. At least on my board USB seems a bit flaky, I need two "usb reset" sequences after the "usb start" to detect an USB hard drive. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Liviu Dudau <liviu.dudau@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-05-07arm: juno: Enable OF_CONTROLAndre Przywara
The Arm Juno board was still somewhat stuck in "hardcoded land", even though there are stable DTs around, and one happens to actually be on the memory mapped NOR flash. Enable the configuration options to let the board use OF_CONTROL, and add a routine to find the address of the DTB partition in NOR flash, to use that for U-Boot's own purposes. This can also passed on via $fdtcontroladdr to any kernel or EFI application, removing the need to actually load a device tree. Since the existing "afs" command and its flash routines require flash_init() to be called before being usable, and this is done much later in the boot process, we introduce a stripped-down partition finder routine in vexpress64.c, to scan the NOR flash partitions for the DT partition. This location is then used for U-Boot to find and probe devices. The name of the partition can be configured, if needed, but defaults to "board.dtb", which is used by Linaro's firmware image provided. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-05-05Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xxTom Rini
- Add DM model for P1010RDB - Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB, MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB, P5040DS - Fix reference to READM.qe_firmware
2020-05-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Support 64-bit U-Boot as the payload for coreboot x86
2020-05-04Merge tag 'u-boot-imx-20200502' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx i.MX for 2020.07 ---------------- - imxrt: fix LCD clock, fix doc - new board: Coral Dev - imx8: enable Cache in SPL. SNVS, update SCFW API - imx8MM: fix reset, 8MQ quand and QuadLite, CPU speed grading - MX6ULL : is_imx6ull to include i.MX6ULZ - Net: add config to enable TXC delay Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/682033914
2020-05-04Merge tag 'u-boot-rockchip-20200501' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - dts clean up to use -u-boot for px30, rk3399 boards - dts sycn from upstream kernel for rk3328, rk3399 - add rockchip rng driver - new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
2020-05-04x86: Add a 64-bit 'coreboot64' buildSimon Glass
Coreboot is a first-stage bootloader mostly used on x86 devices as an alternative to UEFI. Coreboot runs in 32-bit mode. U-Boot currently supports booting from coreboot as a second-stage bootloader, also in 32-bit mode. However it is useful to be able to run U-Boot in 64-bit mode. To do this we can have a 32-bit SPL which switches over the CPU and jumps to a 64-bit U-Boot proper. Add a new 'coreboot64' board for running 64-bit U-Boot from coreboot. This uses binman to create an image with a 32-bit SPL and a 64-bit U-Boot. This allows running 64-bit EFI images on x86, for example, without needing a native U-Boot port for a board. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-04configs: P1010RDB: Enable PCIe driverHou Zhiqiang
Enable the DM PCIe driver in P1010RDB defconfigs. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04powerpc: Enable device tree support for P1010RDBHou Zhiqiang
Add device tree for P1010RDB boards and enable CONFIG_OF_CONTROL so that device tree can be compiled. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: T1042D4RDB: enable DM_I2C and DM_RTCBiwen Li
This enables DM_I2C and DM_RTC in T1042D4RDB defconfigs, except T1042D4RDB SECURE_BOOT defconfig Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: T2080: enable DM_I2CBiwen Li
This enables DM_I2C in T2080 defconfigs Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: T4240RDB: enable DM_I2CBiwen Li
This enable DM_I2C in T4240RDB defconfigs Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: MPC8548CDS: enable DM_I2CBiwen Li
This enables DM_I2C in MPC8548CDS defconfigs Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: P1010: Enable DM_I2C and DM_RTCBiwen Li
Enable DM_I2C and DM_RTC in P1010RDB defconfigs, except P1010RDB SECBOOT defconfigs. Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: T1024RDB: enable DM_I2C and DM_RTCBiwen Li
This enables DM_I2C and DM_RTC in T1024RDB defconfigs, except T1024RDB SECURE_BOOT defconfig Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: P4080DS: enable DM_I2CBiwen Li
This enables DM_I2C in P4080DS defconfigs, except P4080DS SRIO_PCIE_BOOT and SECURE_BOOT defconfigs Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: P3041DS: enable DM_I2CBiwen Li
This enables DM_I2C in P3041DS defconfigs, except P3041DS SECURE_BOOT and SRIO_PCIE_BOOT defconfig Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04config: P2041RDB: enable DM_I2CBiwen Li
This enables DM_I2C in P2041RDB defconfig, except P2041RDB SRIO_PCIE_BOOT and SECURE_BOOT defconfigs Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04configs: P2020RDB: enable DM_I2C and DM_RTCBiwen Li
This enables DM_I2C and DM_RTC in P2020RDB defconfigs Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-12 20:36:22 +0000