summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2019-10-08pico-imx6ul: Add DWARF baseboard supportOtavio Salvador
This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08configs: imx8qm/qxp_mek: enable CONFIG_OF_SYSTEM_SETUPPeng Fan
Enable CONFIG_OF_SYSTEM_SETUP to let U-Boot could disable device tree nodes that could not be used by Linux. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8qm_mek: switch to use container imagePeng Fan
Because FIT could not be used for AHAB secure boot on i.MX8, so switch to use container image that could let SPL verify ATF and U-Boot with AHAB. Enable HUSH_PARSER in defconfig to make run netboot could work. Note: The AHAB related code has not been added. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8qxp_mek: switch to use container imagePeng Fan
Because FIT could not be used for AHAB secure boot on i.MX8, so switch to use container image that could let SPL verify ATF and U-Boot with AHAB. Note: The AHAB related code has not been added. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6sabresd: fix usb start when DM enabledPeng Fan
Enable CONFIG_DM_REGULATOR_FIXED to let vbus regulator work. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08Kconfig: Migrate CONFIG_CSF_SIZE to KconfigBreno Matheus Lima
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000. mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08mx6sabresd: Reduce overall SPL sizeFabio Estevam
Currently the SPL binary is 67 kB, which leaves only 1 kB of free internal RAM space. The following options can be safely removed to save some precious SPL space: - CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd command (at offset 69 kB) - CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL - CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported by default After this change the SPL binary size gets down to 51 kB. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Enable fuse comamndPeng Fan
Enable fuse command Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix wrong i2c configuration nameYe Li
Wrong I2c driver configuration name is used in codes, so I2c driver is not built. Correct it. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb bootPeng Fan
Since the SD3.0 kernel driver needs M4 image support, this causes problem for usb boot booting into kernel. To decouple the relationship, we modify the FDT file in u-boot to disable SD3.0. So the kernel won't depend on M4 image. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08configs: nitrogen6x: Add DM_SPI/DM_SPI_FLASH supportTroy Kisky
Add CONFIG_DM_SPI/CONFIG_DM_SPI_FLASH to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_GPIO supportTroy Kisky
Add CONFIG_DM_GPIO to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This is in preparation for adding CONFIG_DM_SPI. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_MMC/DM_USB/AHCI supportTroy Kisky
Add DM_MMC to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This commit is adding multiple configs, but seems to be the minimum change to not lose features and still compile fine. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08nitrogen6x: migrate to using device treeTroy Kisky
Migrate to using device tree required for further driver model integration. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08imx: mx6slevk: enable DM_SPI and DM_SPI_FLASHPeng Fan
With DM_SPI and DM_SPI_FLASH enabled, we could get: spi 0 [ ] mxc_spi | | | `-- ecspi@02008000 spi_flash 0 [ ] spi_flash_std | | | `-- m25p80@0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6ul_14x14_evk: convert to DM_VIDEOPeng Fan
To support DM_VIDEO, Add display node for lcdif Drop board iomuxc settings. Enable DM_VIDEO Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08imx: add i.MX6ULZ boardPeng Fan
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible with i.MX6ULL. so most code of i.MX6ULL can be reused by i.MX6ULZ. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-06arm: socfpga: disable CONFIG_SPL_WDT for gen5 and a10Simon Goldschmidt
These boards don't have a watchdog enabled in SPL, so make sure CONFIG_SPL_WDT is not enabled. Fixes: commit 6874cb72204f ("watchdog: Split WDT from SPL_WDT") Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-04Kconfig: Migrate CONFIG_BOOTM_* optionsTom Rini
Migrate all of the existing OS support options that are under CONFIG_BOOTM_* to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-01rpi4: enable dram bank initializationMatthias Brugger
When booting through the efi stub, the memory map get's created by reading the dram bank information. Depending on the version of the RPi4 this information changes. Read the device tree to initialize the dram bank data structure. This way the kernel is able to access the whole range of available memory. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-30arm: at91: gardena-smart-gateway-at91sam: Enable CONFIG_SYS_NAND_USE_FLASH_BBTStefan Roese
This patch enables the BBT in NAND on the AT91SAM based GARDENA smart Gateway. This is especially important, since the Linux driver also enables this option and uses the BBT table pages. Without setting this option, U-Boot will try to re-use these pages again (e.g. UBI). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Tom Rini <trini@konsulko.com>
2019-09-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-22Merge tag 'fixes-for-2019.10' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-video.git - fix sunxi LCD clock divider - fix splash logo with DM_VIDEO and CONFIG_VIDEO_LOGO - fix splash banner output with DM_VIDEO
2019-09-21imx: mx6sabreauto: fix splash logo drawingAnatolij Gustschin
Enable BMP code. Also configure white on black for video console. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-09-21imx: icore: fix splash logo drawingAnatolij Gustschin
Define "splashimage" variable in the default environment and enable BMP code. Also configure white on black for video console. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-09-21imx: mx6sabresd: fix splash logo drawingAnatolij Gustschin
After mxc_ipuv3 DM_VIDEO conversion showing splash image doesn't work. Fix this. Also enable white on black console configuration as it used to be with cfb_console driver. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reported-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <festevam@gmail.com>
2019-09-21imx: wandboard: fix splash logo drawingAnatolij Gustschin
After mxc_ipuv3 DM_VIDEO conversion showing splash image doesn't work. Fix this. Also enable white on black console configuration as it used to be with cfb_console driver. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-09-19rockchip: config: evb-rk3288: enable SPL_STACK_RKever Yang
We need a new STACK in SDRAM instead of SRAM so that the EMMC controller can work properly. The EMMC/SD controller's master is not able to access SRAM area, it can only access DRAM area. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-19rockchip: evb-rk3288: Drop explicit SPL_TEXTKever Yang
SPL_TEXT_BASE is 0x0 by default, based on the kconfig definition move in below commit. "configs: move CONFIG_SPL_TEXT_BASE to Kconfig" (sha1: f89d6133eef2e068f9c33853b6584d7fcbfa9d2e) So, don't define it explicitly. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-19rockchip: rk3288-tinker: Attach missing peripherals at SPLMichael Trimarchi
Tinker board needs to mux all the sdmmc gpio and activate the regulator connected to bank 7. Remove all the bank that are not in use and mark them as dm,spl so-that it would initialize at SPL. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-19configs: tinker: Enable SDRAM, SPL stackJagan Teki
SPL sets up SDRAM while in its board_init_f() function, it is possible for the stack to move there before board_init_r() is reached. So it is required to reserve the stack for SDRAM, with a proper location and size otherwise any operations during SPL handoff would leads to failure. On, this particular context tinker-rk3288 SPL is failing to launch U-Boot proper on SDRAM due to lack of stack. U-Boot SPL 2019.10-rc3-00297-g5ba8b12543 (Sep 12 2019 - 08:50:36 +0530) Trying to boot from MMC1 spl: mmc init failed with error: -110 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### So, enable SPL_STACK_R_ADDR and it's related-config items for SDRAM, SPL stack to setup properly. Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-19configs: tinker: Drop explicit SPL_TEXTJagan Teki
SPL_TEXT_BASE is 0x0 by default, based on the kconfig definition move in below commit. "configs: move CONFIG_SPL_TEXT_BASE to Kconfig" (sha1: f89d6133eef2e068f9c33853b6584d7fcbfa9d2e) So, don't define it explicitly. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-19configs: vyasa-rk3288: Fix SPL_TEXT_BASEJagan Teki
The initial Vyasa-rk3288 TPL implementation is to reuse the SPL_TEXT_BASE for TPL and SPL as 0x0 and 0xff704000 respectively. But the below commit implements the reverse way of using TEXT_BASE's like 0xff704000 for TPL and 0x0 for SPL and which indeed update the SPL_TEXT_BASE for vyasa-rk3288 board. "rockchip: Kconfig: enable TPL support for rk3328" (sha1: 3f47db0275e0f1c1e89d8f13f8b4cdc86b1038ca) So, fix by dropping the legacy SPL_TEXT_BASE and it will reassign 0x0 by default based on Kconfig definition. Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-19configs: rockpro64-rk3399: Enable CONFIG_MISC_INIT_R and ROCKCHIP_EFUSEHugh Cole-Baker
This enables reading the cpuid from e-fuse, and deriving a static MAC address from it. Without this, the ethernet interface on the rockpro64 can't be used to boot. Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-16Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Add emmc hs200 support - Few bug fixes related to serdes, I2C, ethernet, etc
2019-09-15Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2019-09-14sh: r2dplus: Enable DHCP commandMarek Vasut
Enable the "dhcp" command as a minor convenience. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-09-13configs: am65x_hs_evm: Use FIT images when booting HS devicesAndrew F. Davis
HS devices use the FIT post processing step to authenticate boot images. Set the configured boot command to load FIT by default. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-09-13ARM: omapl138_lcdk: Enable PinctrlAdam Ford
The single pinctrl supports the da8xx, so this patch enables pinctrl in U-Boot. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-09-13ARM: omapl138_lcdk: Enable DM_GPIO and DM and GPIO CommandsAdam Ford
The da8xx GPIO driver is available with DM_GPIO support. This patch enables the CMD_GPIO, CMD_DM, and DM_GPIO and DA8XX_GPIO. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-09-13ARM: omapl138_lcdk: Disable SPL_DM_USBAdam Ford
The USB was just recently enabled, so it is unlikely anyone is using it in SPL, so this patch removes it from SPL to further reduce the SPL code size. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-09-13arm: am437x: cm-t43: Enable DM for MMC, USB, SPI, SPI_FLASH, enable BLKSuniel Mahesh
Enable driver model for USB, MMC, SPI and SPI_FLASH. Also enable BLK. This will remove the following compile warnings: ===================== WARNING ====================== This board does not use CONFIG_DM_MMC. Please update the board to use CONFIG_DM_MMC before the v2019.04 release. ==================================================== ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. ==================================================== ===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release. ==================================================== Target was compile tested, build was clean. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
2019-09-13arm: am437x: cm-t43: Add device tree, enable OF_CONTROLSuniel Mahesh
Add device tree from Linux for driver model conversion and enable OF_CONTROL. This will remove the following compile warning: ================================================== Device Tree Source is not correctly specified. Please define 'CONFIG_DEFAULT_DEVICE_TREE' or build with 'DEVICE_TREE=<device_tree>' argument =================================================== Target was compile tested, build was clean. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
2019-09-12board: fsl: lx2160a: implement board_fix_fdtPankaj Bansal
lx2160a rev1 and rev2 SoC has different pcie controller. The pcie controller device tree node fields "compatible" and registers names needs to be updated accordingly This change in device tree is handled as part of fdt fixups. These changes would only be applied if the soc revision is not rev1. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12configs/ls1012ardb,lx2160ardb,ls1028ardb: add esdhc hs200 configYinbo Zhu
Enable CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK and CONFIG_MMC_HS200_SUPPORT config for ls1012ardb, ls1012ardb, lx2160ardb in defconfig file Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-08Merge tag 'mmc-9-6-2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
Bug fixes to mmc_spi Add Aspeed SD driver Fix dw_mmc timeout calculation Fix timeout values passed to mmc_wait_dat0 sdhci dt caps/mask update [trini: Fix evb-ast2500_defconfig CONFIG_MMC line] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-07Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Initial DM conversion
2019-09-06Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-bootTom Rini
- fix mailbox status register used for polling - fix bcm2835_sdhost to wait long enough for a transfer to complete - increase kernel image size from 8 MB to 64 MB on arm64 - add support for RPi4 - add prefixes for raspberry pi related stuff to git-mailrc
2019-09-06RPI: Add defconfigs for rpi4 (32/64)Andrei Gherzan
This defines a minimum defconfig for each of the two Raspberry Pi 4 variants. One notable difference is that we don't have a embedded dt for this board given that the fw supplies us with one which we can reuse. Furthermore, the ram size is not queryable through mbox interface as the maximum reported size is 1G. The fw patches the dt with the right memory configuration and uboot uses it as it is. We avoid u-boot touching this configuration by making sure CONFIG_ARCH_FIXUP_FDT_MEMORY is deactivated. Signed-off-by: Andrei Gherzan <andrei@balena.io> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-05riscv: qemu: enable CONFIG_CMD_BOOTEFI_SELFTESTHeinrich Schuchardt
Enable CONFIG_CMD_BOOTEFI_SELFTEST for the QEMU RISC-V boards. Travis CI QEMU testing has been enabled for qemu-riscv64_defconfig. With this patch we will test the UEFI sub-system on the board. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-10 14:31:38 +0000