Age | Commit message (Collapse) | Author |
|
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
zc1751 is based board with dc3 extenstion card which is used for silicon
validation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add support for Xilinx zcu100.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch enables the fixed link support for
all ZynqMP boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no memory which stores mac address that's why generate it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable ethernet phys for zc1751 dc5.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.
To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Makes naming in line with other Zynq boards.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the CONFIG_TSEC_ENET option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Migrate the CONFIG_LAST_STAGE_INIT option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move am43xx_evm_qspiboot_defconfig to DM. This is required as SPI core
and TI QSPI driver no longer supports non DM interfaces.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh vutla <lokeshvutla@ti.com>
|
|
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable NETCONSOLE by default. Still requires changes to the boot
environment to enable on the platform.
Signed-of-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This converts CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
Some config is redundant with Kconfig. Fix it.
Also remove unused configs
Move SDRAM_MAX_SIZE in the only place it is used
include/environment.h already defines CONFIG_ENV_SIZE
from CONFIG_ENV_SECT_SIZE and defines CONFIG_ENV_ADDR as
(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
remove BOOTARGS as bootargs is set by the different boot commands
Fix CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE to be in
line with CPM DPRAM organisation
Remove CONFIG_SYS_GBL_DATA_SIZE, CONFIG_SYS_GBL_DATA_OFFSET and
CONFIG_SYS_INIT_SP_OFFSET which are unused
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
ATMEL_SPI is now fully converted to driver-model and
respective boards switch to DM_SPI as well,
so make default y for ARCH_AT91
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
|
|
Enable SPL Driver model and FDT support for AT91 ma5d4evk boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Sync DTS from Linux and add FDT support for AT91 ma5d4evk board.
usb0, usb1, usb2 and hlcdc_pwm nodes removed, since there is no support it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Sync DTS from Linux and add FDT support for AT91 vinco board.
usb0, usb1, and usb2 nodes removed, since there is no support it.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Now CONFIG_ATMEL_SPI is defined in Kconfig, so move the
same into defconfig file.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
|
|
Patch queue for rpi - 2018-04-06
Highlights this time around:
- Support for new RPi3 B+ model
- Fix for some SD cards on newer RPi firmware
|
|
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add
driver support in U-Boot for it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add
driver support in U-Boot for it.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
When we enable CONFIG_OF_BOARD on Raspberry Pis, we may end up without
serial console support in early boot. Hence we need to make the serial
port optional, otherwise we will never get to the point where serial
would be probed.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Now with the MMC environment gone, we have enough space to accommodate
the Pine64 "non-plus" .dtb again.
This reverts commit 47952b8e42c2790150e16d3d4235b3a1ee0ba9bb.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add NAND parameters to the Nintendo NES Classic configuration file which
features a Macronix NAND flash chip with 128kiB blocks of 2kiB pages
plus 64 OOB bytes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Move the NAND parameters from defconfig files to Kconfig for SUNXI
architecture only. Fort now only the CHIP pro is migrated.
It would have been better to convert this defconfig entry to Kconfig for
all supported machines/architectures but it has been abandoned due to a
fairly high amount of errors reported by the moveconfig.py tool. This is
due to defines quite often being multiplications of values/other defines
not correctly handled.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Remove NAND_SUNXI from the CHIP pro defconfig to be automatically
selected depending on the state of ARCH_SUNXI.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Make SUNXI_NAND select SPL_NAND_SUPPORT in Kconfig, this limit the
number of entries to add in defconfig files when adding NAND support.
For now, the only board using it is the CHIP pro.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
HSDK board has sst26wf016 SPI flash IC which we want to support.
Add SPI controller, CS-gpio and SPI flash nodes to hsdk device tree.
Enable corresponding options in hsdk defconfig.
For SPI write functionality to work we need [1] which
adds support of sst26xxx ICs.
[1] https://patchwork.ozlabs.org/project/uboot/list/?series=35796
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
This patch add support of hsdk platform-specific commands:
hsdk_clock set - set clock from axi_freq, cpu_freq and tun_freq
environment variables/command line arguments
hsdk_clock get - save clock frequencies to axi_freq, cpu_freq
and tun_freq environment variables
hsdk_clock print - show CPU, AXI, DDR and TUNNEL current
clock frequencies.
hsdk_clock print_all - show all currently used clock frequencies.
hsdk_init - setup board HW in one of pre-defined configuration
(hsdk_hs34 / hsdk_hs36 / hsdk_hs36_ccm / hsdk_hs38 /
hsdk_hs38_ccm / hsdk_hs38x2 / hsdk_hs38x3 / hsdk_hs38x4)
hsdk_go - run baremetal application on hsdk configured
by hsdk_init command.
This patch changes default behaviour of 'bootm' command:
now we are able to set number of CPUs to be kicked by setting
'core_mask' environment variable before 'bootm' command run.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
|
|
|
|
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch enable the PINCTRL and GPIO support, including the GPIO
command on the Armada 3720 espressobin board.
Reviewed-on: http://vgitil04.il.marvell.com:8080/40746
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Wilson Ding <dingwei@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This makes the network devices usable when booting a blank board over
UART, with no pre-configured MAC address stored in the environment area.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable CONFIG_OF_BOAD to support delivery dtb to u-boot
at run time instead of embedded.
There are two methods to delivery dtb.
1 Pass from loader:
When u-boot boot from RAM, gdb or loader can pass dtb
via a2 to u-boot dynamically. Of course gdb or loader
shall be in charge of dtb delivery.
2 Configure CONFIG_SYS_FDT_BASE:
It can be configured as RAM or ROM base statically,
no mater u-boot boot from RAM or ROM.
If it was configured as ROM base, dtb can be burned
into ROM(spi flash) by spi driver.
Meanwhile remove CONFIG_SKIP_LOWLEVEL_INIT which is
useless in nx25-ae250 configuration.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
Remove CONFIG_MMC_NDS32 from the three config
(adp-ae3xx_defconfig, adp-ag101p_defconfig, nx25-ae250_defconfig).
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|