summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2020-06-18configs: atmel: cleanup CONFIG_SPL_SEPARATE_BSSGregory CLEMENT
Now that CONFIG_SPL_SEPARATE_BSS is selected for all the AT91 based boards, cleanups the defconfigs by removing it. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2020-06-16ARM: da850-evm: Remove SPI from SPL when booting from NANDAdam Ford
The da850evm boots from SPI flash while the da850evm_nand_defconfig boots from NAND and these are configs are mutually exclusive. Since there isn't a need for SPI during SPL in the NAND configuration, this patch removes the SPI drivers in SPL while making them still available in U-Boot proper. This should save some code space in SPL. Signed-off-by: Adam Ford <aford173@gmail.com>
2020-06-16omap5: uevm: convert to device modelTero Kristo
Convert omap5 uevm board to device model. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16omap4: sdp: convert to device modelPeter Ujfalusi
Convert omap4 sdp to device model. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16omap4: panda: convert to device modelTero Kristo
Convert omap4 panda to device model. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-13mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPLFaiz Abbas
Cleanup this driver to use dt in U-boot and static platdata in SPL. This requires the following steps: 1. Move all platdata assignment from probe() to ofdata_to_platdata(). This function is only called in U-boot. 2. Replicate all the platdata assignment being done in ofdata_to_platdata() in the omapl138 board file. This data is used in the SPL case where SPL_OF_CONTROL is not enabled. 3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL') Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-06-13Merge tag 'dm-pull-12jun20' of git://git.denx.de/u-boot-dm into nextTom Rini
patman improvements to allow it to work with Zephyr change to how sequence numbers are assigned to devices minor fixes and improvements
2020-06-12net: phy: Add support for TI PHY initDan Murphy
ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com>
2020-06-12board: tbs2910: Enable distro_boot support.Denis 'GNUtoo' Carikli
This keeps the compatibility with the old bootcmd. The fdtfile environment variable also needed to be set to imx6q-tbs2910.dtb to enable booting mainline kernels otherwise with extlinux.conf it tries to load mx6-tbs2910.dtb instead. With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution, we have the following size differences: - text: +2041 bytes - data: 0 bytes - bss: 0 bytes - total: +2041 bytes Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Reviewed-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910_defconfig: Add support for booting general purpose distributionsDenis 'GNUtoo' Carikli
This is needed to enable distro_boot support later on. Adding the necessary configuration to enable booting general purpose distributions is typically done by enabling CONFIG_DISTRO_DEFAULTS. However the resulting image size is is already very close to the size limit and PXE isn't strictly needed, so instead we made sure that all the configuration selected by CONFIG_DISTRO_DEFAULTS were selected, with the exception of PXE related configuration (CONFIG_BOOTP_PXE and CONFIG_CMD_PXE) that are both disabled. With arm-linux-gnueabi-gcc 9.3.0-1 from the Parabola GNU/Linux distribution, we have the following size differences: - text: +7526 bytes - data: +28 bytes - bss: -12 bytes - total: +7542 bytes Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Reviewed-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910: move CONFIG_BOOTCOMMAND from header to defconfigDenis 'GNUtoo' Carikli
This doesn't affect the size of the image: with arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution, the text, data, bss and total sizes remain unchanged. Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Reviewed-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910: disable CONFIG_GZIPDenis 'GNUtoo' Carikli
As that the resulting image is already very close to the size limit, and that CONFIG_GZIP is not strictly required, removing it shouldn't hurt. With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution we have the following size reduction: - text: 9752 - data: 0 - bss: 16 - total: 9768 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Acked-by: Soeren Moch <smoch@web.de>
2020-06-12board: tbs2910: disable loadb and loads commandsDenis 'GNUtoo' Carikli
The loadb and loads commands are not needed for booting. There are also more reliable and faster alternatives to loadb and loads that can be used with the current configuration. As that the resulting image is already very close to the size limit, removing the loadb and loads commands shouldn't hurt. With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux distribution we have the following size reduction: - text: 6733 bytes - data: 116 bytes - bss: 1172 bytes - total: 8021 bytes Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> Acked-by: Soeren Moch <smoch@web.de>
2020-06-11configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-11am335x: sl50: Enable DM_SPIJagan Teki
Enable DM_SPI for am355x sl50 board. Build is fine, but not tested. Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2020-06-11configs: igep00x0: Enable DM_SPIJagan Teki
Enable DM_SPI for igep00x0 board. Build is fine, but not tested. Cc: Enric Balletbo i Serra <eballetbo@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2020-06-11arm: Remove pcm051 boardJagan Teki
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Acked-by: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-11arm: Remove omap3_pandora_defconfig boardJagan Teki
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Acked-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-11ks2_evm: Switch to DM_SPL, SPL_OF_CONTROLJagan Teki
This would make SPL build to DM_SPL, SPL_OF_CONTROL. Build fine with but not tested. Cc: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-09Merge tag 'u-boot-imx-20200609' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.07 ----------------- - mx53: mx53menlo Convert to DM_ETH, fix fail boot - imx8mp_evk: fix boot issue - MX6, display5: fix environment - drop warnings (watchdog) for i.MX8mm i.mx8mp - enable bootaux for i.MX8M Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/695929999
2020-06-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xxTom Rini
- DM_ETH support for P2041RDB, T1024RDB, P5040DS, P3041DS, P4080DS, bug fixes - Add TBI PHY access through MII - DDR: Rework errata workaround for A008109, A008378, 009942
2020-06-08ARM: dts: imx: m53menlo: Convert to DM_ETHMarek Vasut
Convert the board to DM_ETH instead of legacy networking. This requires a minor addition to the DT to satisfy the requirement for specifying a PHY node. No functional change from board user perspective. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-08imx: imx8mp_evk: fix boot issuePeng Fan
The u-boot-spl.bin pad with ddr firmware conflicts with the CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten by malloc in SPL stage and cause ddr initialization not able to finish. So update the related addresses to fix the issue. Reported-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx: Update MTD partitions layout for display5 (i.MX6Q) boardLukasz Majewski
This change updates the MTD partition layout on SPI-NOR memory for display5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-06-08verdin-imx8mm: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-08imx8mp_evk: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mm_beacon: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Adam Ford <aford173@gmail.com>
2020-06-08imx8mn_ddr4_evk: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mm_evk: Select the watchdog driverFabio Estevam
Currently the watchdog driver is not selected, which causes the following warnings in both SPL and U-Boot proper: U-Boot SPL 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300) Normal Boot WDT: Started without servicing (60s timeout) Trying to boot from MMC1 U-Boot 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300) CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz Reset cause: POR Model: FSL i.MX8MM EVK board DRAM: 2 GiB WDT: Started without servicing (60s timeout) .... System reboots after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Suggested-by: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-07rockchip: enable PCIe and NVMe on Pinebook ProPatrick Wildt
Enable CONFIG_PCI and CONFIG_NVME and related configs for the Pinebook Pro. Signed-off-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: enable new usb config optionsHeiko Stuebner
With recently added changes we get support for usb3 including handling of the phys (type-c and inno-usb2), so enable the necessary config options on puma. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: remove separate fit generatorHeiko Stuebner
The introduction of the puma-specific generator was mainly a way to split the pmu firmware from the ATF binary and not having to distribute that 4GB (sparse) image that was created before moving to the bl31.elf as base. Looking at the publically available repository for that separate pmu firmware https://git.theobroma-systems.com/rk3399-cortex-m0.git/ there is also no activity for 3 years and apart from some build customizations no other changes were done. And even then, if changes need to be made, this can very well also happen in the atf context itself, so there is no real need to diverge from the established build procedure and we can just go back to using the main make_fit_atf.py script. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: reorganize devicetrees to actually work and match upstreamHeiko Stuebner
So far the puma dts files only just included the main puma dtsi without handling the actual baseboard and rk3399-puma.dtsi was very much detached from the variant in the mainline Linux kernel. Recent changes resulted in a strange situation with nonworking puma boards. Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi") moved the sdram include from rk3399-puma-ddrX.dts to new files rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though. Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") replaced the rk3399-puma.dtsi nearly completely, but in the kernel it definitly depends on a baseboard dts to actually enable peripherals like sd-slot, uarts, etc. So to untagle this and bring the whole thing more in line with mainline Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate DDR-option devicetrees and instead replace them with a puma Kconfig option to select and include the needed DDR variant. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: add SPI bootMarcin Juszkiewicz
U-Boot TPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) Trying to boot from SPI U-Boot 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: vidconsole Err: vidconsole Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 => Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: Store default env into SPIMarcin Juszkiewicz
Board has flash chip on board so let store U-Boot environment there. Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Add SPI bootJagan Teki
U-Boot TPL 2020.07-rc3-00090-gd4e919f927-dirty (Jun 01 2020 - 23:45:53) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) Trying to boot from MMC1 NOTICE: BL31: v2.2(release): NOTICE: BL31: Built : 15:05:37, May 12 2020 U-Boot 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) SoC: Rockchip rk3399 Reset cause: POR Model: Firefly ROC-RK3399-PC Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Model: Firefly ROC-RK3399-PC Board Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Mark default env from SPIJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Updated env offset, size in contrast with default since the U-Boot proper has to start from 384K. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3328: add rock-pi-e-rk3328_defconfig fileb.l.huang
This commit add the default configuration file and relevant description for rock-pi-e board Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-07rockchip: Enable PCIe and NVMe on ROCKPro64Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the ROCKPro64 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: Enable PCIe/M.2 and NVMe on Firefly RK3399Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the Firefly RK3399 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BOARD_LATE_INIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOARD_LATE_INIT Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BZIP2 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04topic_miami: Disable GPIOTom Rini
Per the boards config header file, there is no useful GPIO on these boards. Remove CONFIG_CMD_GPIO from the defconfigs. Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04ARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPITom Rini
The config header for this platform disables both CMD_SF and CMD_SPI and the defconfig leaves them enabled. Disable them from the defconfig and enable them in the header. Cc: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04bcmstb: Migrate CONFIG_CMD_EXT[24]Tom Rini
The common config header for bcm7260 and bcm7445 enable CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the commands being disabled. Enable them via the defconfig. Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04mx6memcal: Finish migration to defconfig optionsTom Rini
The config header for this platform uses '#undef' in a number of cases. All of the MMC related ones were already handled correctly in the defconfig file. In the case of CONFIG_CMD_FUSE, the command was being built and enabled via defconfig. Disable it in the defconfig, cleanup the header. Reviewed-by: Eric Nelson <eric@nelint.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04pfla02: Rework excluding NAND from SPLTom Rini
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD options to defconfig and rework the guards to not try and call the function in SPL builds. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stefano Babic <sbabic@denx.de>
2020-06-04serial: Convert ARM_DCC to KconfigTom Rini
The symbol "CONFIG_ARM_DCC" is used to control building drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this. Cc: Luca Ceresoli <luca@lucaceresoli.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
generated by cgit (git 2.34.1) at 2025-01-23 18:13:01 +0000