summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2019-04-23poplar: enable Ethernet driver supportShawn Guo
The 'phy' reset of gmac device in kernel device tree is not generic enough for u-boot to use, so we need to overwrite the 'resets' property as needed. With this device tree fixup and poplar_defconfig changes, Ethernet starts working on Poplar board. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-23bcm963158: enable led supportPhilippe Reynes
Enable the led support in the configuration of the board bcm963158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-23bcm968580xref: enable led supportPhilippe Reynes
Enable the led support in the configuration of the board bcm968580xref. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-23configs: stm32f746-disco: Enable SPI_FLASH_MACRONIXPatrice Chotard
This config file is shared between stm32f746-disco and stm32f769-disco. These 2 boards doesn't embed the same qspi flash (Micron n25q128a on f746-disco, Macronix mx66l51235l on f769-disco). To be able to use Macronix mx66l51235l on F769-disco, flags SPI_FLASH_MACRONIX must be enabled. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23configs: stm32f746-disco: enable CONFIG_DISTRO_DEFAULTSPatrice Chotard
Allows to boot linux distribution Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-23board: amlogic: enable PHY_REALTEK for selected boardsNeil Armstrong
When using the generic PHY on boards using an RGMII Realtek PHY, gigabit speed is not always reliable. This patch enables the Realtek PHY driver for such boards. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-23boards: meson: add g12a u200Jerome Brunet
The Amlogic U200 board is based on the Amlogic S905D2 SoC from the Amlogic G12A SoC family. The board has the following specifications : - Amlogic S905D2 ARM Cortex-A53 quad-core SoC - XGB DDR4 SDRAM - 10/100 Ethernet (Internal PHY) - 1 x USB 3.0 Host - eMMC - SDcard - Infrared receiver - SDIO WiFi Module - MIPI DSI Connector - Audio HAT Connector - PCI-E M.2 Connector Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-23efi_loader: disable EFI_LOADER on vexpress_ca15_tc2 and ca9x4Heinrich Schuchardt
vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig do not provide device trees (as $fdtcontroladdr) as needed to pass our Travis CI tests. As we are on the move to requiring block devices to be based on the driver model these boards either will have to be converted to use device trees or will be kicked out of U-Boot. So let's disable CONFIG_EFI_LOADER on these boards until the device tree issue is resolved. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-04-22bcm963158: add nand supportPhilippe Reynes
Enable the nand support (driver and command) in the configuration of the board bcm963158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22bcm968580xref: add nand supportPhilippe Reynes
Enable the nand support (driver and command) in the configuration of the board bcm968580xref. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22bcm968380gerg: add nand supportPhilippe Reynes
Enable the nand support (driver and command) in the configuration of the board bcm96838gerg. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-22Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmelTom Rini
Second set of u-boot-atmel features and fixes for 2019.07 cycle
2019-04-22at91: corvus_defconfig: get rid of build warningsHeiko Schocher
fix CONFIG_OF_EMBED and add CONFIG_DM_USB build warnings. Signed-off-by: Heiko Schocher <hs@denx.de>
2019-04-21Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- Various fastboot, dwc2/stm32 updates
2019-04-21Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- Various stratix10, gen5 updates
2019-04-21stm32mp1: migrate USBOTG device to driver modelPatrick Delaunay
Use the DWC2 device driver with DM_USB_GADGET support and cleanup the USB support in STM32MP1 board. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-21stm32mp1: remove CONFIG_USB_DWC2, HOST support for USBOPatrick Delaunay
Remove the HOST support for STM32MP1 USBO device = OTG DWC2. The current DWC2 driver have no dynamic detection of device, So it is dangerous to have start 3V3 when PC is connected to the micro USB connector. => it is preferable to have only DEVICE support CONFIG_USB_GADGET_DWC2_OTG for OTG port See DWC3 driver for clean dual role support... Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-19usb: Select USB_MUSB_DSPS with USB_MUSB_TIAlex Kiernan
USB_MUSB_TI requires USB_MUSB_DSPS, failing at link time if it's not selected: drivers/usb/musb-new/built-in.o: In function `ti_musb_host_ofdata_to_platdata': drivers/usb/musb-new/ti-musb.c:193: undefined reference to `musb_dsps_ops' or if OF_CONTROL is not selected: arch/arm/mach-omap2/built-in.o:(.data.usb0+0x24): undefined reference to `musb_dsps_ops' Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at> Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2019-04-18Merge tag 'arc-for-2019.07' of git://git.denx.de/u-boot-arcTom Rini
In this small series we migrate ARC boards to DM_MMC so we're hopefully are good now and our boards will be kept in U-Boot for some more time :)
2019-04-18board: sama5d2_icp: Enable MACB driverRazvan Stefanescu
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
2019-04-18board: atmel: add SAMA5D2 ICP boardEugen Hristev
The SAMA5D2 ICP Board features the SAMA5D27 SoC, together with QSPI Flash, Wilc3000 wireless device and EtherCat support. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-18ARC: [plat-axs10x]: migrate to DM_MMCEugeniy Paltsev
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-04-18ARC: [plat-hsdk]: migrate to DM_MMCEugeniy Paltsev
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-04-17configs: stratix10: Change CONFIG_NR_DRAM_BANKS to 2Ley Foon Tan
Stratix10 maps dram in 2 address spans, from 0-2GB and from 2GB up to 128GB. Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-04-17arm: am57xx: cl-som-am57x: remove board supportUri Mashiach
U-Boot support for the CL-SOM-AM57x module is no longer required. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2019-04-17Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx/FPGA changes for v2019.07 fpga: - Add support for external data in FIT - Extend testing for external data case - Inform user about a need to run post config on Zynq arm: - Tune zynq command functions - Fix internal variable setting arm64: - Add support for zc39dr decoding - Disable WDT for zcu100 - Small changes in reset_reason() - Some DT changes (spi) - Tune qspi-mini configuration - Remove useless eeprom setting - Fix two sdhci boot case spi: - Fix tap delay programming clk: - Enable i2c in SPL net: - Fix gem phydev handling - Remove phy detection code from gem driver general: - Correct EXT_DTB usage for MULTI_DTB_FIT configuration
2019-04-17Merge tag 'uniphier-v2019.07' of git://git.denx.de/u-boot-uniphierTom Rini
UniPhier SoC updates for v2019.07 - Sync DT with Linux 5.1-rc4 - Enable CONFIG_SUPPORT_EMMC_RPMB for uniphier_v8_defconfig
2019-04-17ARM: uniphier_v8: enable CONFIG_SUPPORT_EMMC_RPMBMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-04-16arm64: xilinx: zynqmp: Remove unneeded configsSiva Durga Prasad Paladugu
Remove unneeded configs from mini qspi configuration so that it saves space for this mini configuration. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Disable WDT for zcu100Michal Simek
Do not enable WDT by default on this target because distributions are not enabling watchdog driver to service it. Feature has been enabled by: "arm64: zynqmp: Enable cadence WDT for zcu100" (sha1: 767afebbcda59f3ccb04f6c94de8cab2fb7905b6) And WDT is still enabled in rebranded Avnet Ultra 96 board support. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-15Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imxTom Rini
Move to DM ----------- - DM support in sata - Toradex Board to DM - wandboard to DM - tbs2910 to DM - GE boards to DM - VHybrid boards to DM - DM_VIDEO for i.MX
2019-04-14board: tbs2910: Remove CMD_FDT support in defconfig to reduce u-boot sizeSoeren Moch
This fixes the build failure "u-boot.imx exceeds file size limit". Signed-off-by: Soeren Moch <smoch@web.de>
2019-04-14Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
Conflicts: arch/arm/dts/armada-385-amc.dts arch/arm/dts/armada-xp-theadorable.dts arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-13imx6: wandboard: fix dwc_ahsata build errors when DM enabledAnatolij Gustschin
Enable CONFIG_AHCI to fix errors: drivers/ata/dwc_ahsata.c: In function `ahci_init_one': drivers/ata/dwc_ahsata.c:868:21: error: `struct blk_desc' has no member named `priv' sata_dev_desc[pdev].priv = uc_priv; ^ drivers/ata/dwc_ahsata.c: In function `init_sata': drivers/ata/dwc_ahsata.c:891:30: error: `struct blk_desc' has no member named `priv' uc_priv = sata_dev_desc[dev].priv; ... Also enable DM_SCSI to fix migration build warning. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13config: colibri_vf: enable mtd partitions via dtStefan Agner
Use device tree to set MTD partitions of the NAND chip. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: migrate fec, esdhc, nfc and usb to driver modelMarcel Ziswiler
Migrate FEC, ESDHC, NFC and USB to driver model. While at it also do no longer enable optional I2C clock in board file as the generic clock code now handles this. Note for space reason and as it is not required just for booting we do not enable I2C in U-Boot by default. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: migrate pinctrl and regulators to dtb/dmMarcel Ziswiler
Migrate pinctrl and regulators to device tree resp. driver model: DDR, DSPI, ENET, ESDHC, I2C, NFC and UART. Enable CMD_DM, PINCTRL and DM_REGULATOR. While at it also update copyright period and sort include files. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13configs: colibri_vf: disable obscure optionsMarcel Ziswiler
Disable more obscure options to save another 26 KB in preparation of the upcoming driver model migration. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13configs: move CONFIG_MXC_OCOTP to KconfigMarcel Ziswiler
While commit 3e020f03e94f ("driver: misc: add MXC_OCOTP Kconfig entry") introduced a Kconfig entry it did not actually migrate all configurations to using it. As CONFIG_MXC_OCOTP was in mx{6/7}_common.h enable it by default on those architectures. Additionally, also enable it on ARCH_IMX8M and ARCH_VF610 where all current members enabled it through their legacy configuration header files. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-13configs: colibri_vf: limit size of malloc() pool before relocationMarcel Ziswiler
Limit the size of the malloc() pool before relocation (SYS_MALLOC_F_LEN). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13imx6: wandboard: convert to DM_MMCAnatolij Gustschin
Move SDHC init to SPL code since it is not required with DM_MMC. Enable DM_MMC support. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_I2CAnatolij Gustschin
Allow building with DM_I2C enabled. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_PMICAnatolij Gustschin
Enable DM_PMIC_PFUZE100 driver and add PMIC description to DTS. Rework power_init_board() code. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_VIDEOAnatolij Gustschin
Enable DM_VIDEO in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_USBAnatolij Gustschin
Drop CONFIG_USB_MAX_CONTROLLER_COUNT and enable DM_USB in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_GPIO and enable pinctrl driverAnatolij Gustschin
Enable DM_GPIO and pinctrl in defconfig and add gpio_request() calls where required. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: add device treeAnatolij Gustschin
Add device trees from Linux in preparation for driver model conversions. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13mx6sabreauto: convert to DM_VIDEOAnatolij Gustschin
Enable DM_VIDEO in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13mx6sabresd: convert to DM_VIDEOAnatolij Gustschin
Enable DM_VIDEO in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13colibri_imx6: convert to DM_VIDEOAnatolij Gustschin
Enable DM_VIDEO in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
generated by cgit (git 2.34.1) at 2024-12-29 01:18:33 +0000