summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2020-01-24sunxi: Add Libre Computer ALL-H3-IT H5 boardChen-Yu Tsai
The Libre Computer ALL-H3-IT board is a small single board computer that is roughly the same size as the Raspberry Pi Zero, or around 20% smaller than a credit card. The board features: - H2, H3, or H5 SoC from Allwinner - 2 DDR3 DRAM chips - Realtek RTL8821CU based WiFi module - 128 Mbit SPI-NOR flash - micro-SD card slot - micro HDMI video output - FPC connector for camera sensor module - generic Raspberri-Pi style 40 pin GPIO header - additional pin headers for extra USB host ports, ananlog audio and IR receiver Only H5 variant test samples were made available, but the vendor does have plans to include at least an H3 variant. Thus the device tree is split much like the ALL-H3-CC, with a common dtsi file for the board design, and separate dts files including the common board file and the SoC dtsi file. The other variants will be added as they are made available. The device tree was synced over from the Linux kernel, along with other H3/H5 changes, in a previous patch. Thus only the defconfig and an entry to the MAINTAINERS file is added. Signed-off-by: Chen-Yu Tsai <wens@csie.org> [jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24sunxi: move CONFIG_SYS_SPI_U_BOOT_OFFS out of defconfigAndre Przywara
For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a board choice: The boot ROM only loads the SPL from offset 0 of the SPI NOR flash, and loads at most 32KB. This is a similar situation as on MMC, so consequently we create our "joint" image (SPL + U-Boot proper) with that 32KB offset during the build. So define the value of this symbol to be 32KB by default for every Allwinner SoC. This removes the definition of this symbol from the _defconfig files, and avoids every board to define this over and over again. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24sunxi: defconfig: R40 boards: enable USBAndre Przywara
Now that the USB PHY on the Allwinner R40 SoC is supported, enable USB support for the two R40 boards U-Boot supports. For this we need to add the GPIO pin that powers the USB port(s), also enable the usual suspects (OHCI/EHCI support). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24sunxi: defconfig: Bananapi M2 Berry: enable EthernetAndre Przywara
The M2 Berry features the normal Gigabit PHY connected to the SoC's MAC, so enable the sun8i-emac driver to support Ethernet on the board. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24configs: ls1028aqds: enable mdio muxing by defaultAlex Marginean
LS1028A QDS boards have a MDIO MUX and they require the driver for it for PHYs to work. Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24configs: fsl-layerscape: secure_boot: Enable setexpr commandUdit Agarwal
setexpr command is used while running secure boot (chain of trust with confidentiality) feature. Enable CONFIG_CMD_SETEXPR to enable setexpr command. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24board: fsl: ls1028a: free up arch_misc_initAlex Marginean
Currently LS1028A board code uses arch_misc_init to set up the board mux on QDS. Move this code to misc_init_r. This is consistent with LS gen 2 and T series SoCs/boards. Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24board: fsl: lx2160a: free up arch_misc_initAlex Marginean
Currently LX2 board code uses arch_misc_init to set up the board mux on RDB and QDS. Move this code to misc_init_r. This is consistent with LS gen 2 and T series SoCs/boards. Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24configs: lx2160a: enable CONFIG_OF_BOARD_FIXUP for SECURE_BOOT defconfigWasim Khan
lx2160a rev1 and rev2 SoC has different pcie controller. The pcie controller device tree node fields "compatible" and registers names needs to be updated accordingly. Enable CONFIG_OF_BOARD_FIXUP to apply board_fix_fdt which updates the "compatible" and registers names. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24pci: layerscape: Common device tree fixup for NXP SoCsWasim Khan
Add Common device tree fixup for NXP SoCs. Based on SoC and revision call pcie_layerscape or pcie_layerscape_gen4 fixup. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24configs: ls1012afwry: Enable usb network cards supportYinbo Zhu
Enable RTL8152, AX88179 and AX8817X USB network cards support for ls1012afwry Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24configs: ls1088ardb: Enable usb network cards supportYinbo Zhu
Enable RTL8152, AX88179 and AX8817X USB network cards support for ls1088ardb Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24configs: ls1046afwry: Enable usb network cards supportYinbo Zhu
Enable RTL8152, AX88179 and AX8817X USB network cards support for ls1046afrwy Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-23arm/km: remove unmaintained board kmsuv31Holger Brunck
This target is out of maintenance and can be removed. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-23arm/km: remove unmaintained board SUGP1Holger Brunck
This target is out of maintenance and can be removed. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-23arm/km: add support for SUSE2Holger Brunck
This board is similar to SUV31, but the FPGA is reset concept is quite different. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-23bcm968360bg: add initial supportPhilippe Reynes
This add the initial support of the broadcom reference board bcm968360bg with a bcm68360 SoC. This board has 512 MB of RAM, 256 MB of flash (nand), 2 USB port, 1 UART, and 4 ethernet ports. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-01-22board: Add new Samsung "stemmy" board based on ST-Ericsson U8500Stephan Gerhold
The ST-Ericsson U8500 SoC has been used in mass-production for some Android smartphones released around 2012. In particular, Samsung has released more than 5 different smartphones based on U8500, e.g. - Samsung Galaxy S III mini (GT-I8190) "golden" - Samsung Galaxy S Advance (GT-I9070) "janice" - Samsung Galaxy Xcover 2 (GT-S7710) "skomer" and a few others. Mainline Linux has great support for the Ux500 SoC, so these smartphones can also run Linux mainline quite well. Unfortunately, the original Samsung bootloader used on these devices has limitations that prevent booting Linux mainline directly. It keeps the L2 cache enabled, which causes Linux to crash very early, shortly after decompressing the kernel. Using U-Boot allows to circumvent these limitations. We can let the Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache before booting into Linux. U-Boot has several other advantages - it supports device-trees directly and we are no longer limited to flashing Android boot images through Samsung's proprietary download mode. The Samsung "stemmy" board covers all Samsung devices based on U8500. Add minimal support for "stemmy". For now only UART is supported but this will be extended later. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-21Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Clearfog: Add run-time board detection with TLV EEPROM support (Baruch)
2020-01-21ARM: mvebu: clearfog: add support for EEPROM TLV infoBaruch Siach
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-21Merge tag 'u-boot-imx-20200121' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx --------------------------------- imx8: cleanup, fix warnings imx6ull: add VisionSOM SoM and EVK mx7ulp: fix warning due network, cleanup mx7dsabre: Fix dm probe pmic imx6: fixed for vining2000 Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/639512296
2020-01-20Merge tag '2020-01-20-ti-2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-ti K3 J721E: * DMA support. * MMC and ADMA support. * EEPROM support. * J721e High Security EVM support. * USB DT nodes K3 AM654: * Fixed boot due to pmic probe error. * USB support and DT nodes. * ADMA support DRA7xx/AM57xx: * BBAI board support * Clean up of net platform code under board/ti AM33/AM43/Davinci: * Reduce SPL size for omap3 boards. * SPL DT support for da850-lcdk * PLL divider fix for AM335x
2020-01-20mx7ulp_evk_plugin: Disable CONFIG_NETFabio Estevam
Currently the following build warning is seen: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. =================================================== Since the mx7ulp-evk board does not have networking support, explicitly disable networking. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-01-20ARM: imx: mx6ull: Add iMX6ULL VisionSOM SoM and EVKArkadiusz Karas
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support. The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier board has Ethernet, USB host port, USB OTG port. Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2020-01-20ARM: imx: vining2000: Enable SPL SDP by defaultMarek Vasut
Enable SPL SDP fallback boot option in default build. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Stefano Babic <sbabic@denx.de>
2020-01-20Merge branch 'master' of git://git.denx.de/u-bootStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2020-01-20configs: am65x_evm: Enable USB keyboard as second stdinVignesh Raghavendra
Enable USB keyboard to be used as input device at U-Boot prompt. Both serial and USB keyboard will be active inputs simultaneously. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20am65x_evm_a53_defconfig: Enable configs to support USB and DFUVignesh Raghavendra
Enable configs related to USB Host mode, Peripheral mode and DFU. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20configs: am65x_evm: Add Support for ADMAFaiz Abbas
Add Support for ADMA in a53 and r5 defconfigs. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20configs: omap3/35_logic and omap3/35_logic_somlv: Reduce SPL sizeAdam Ford
Currently the DM37 and OMAP35 boards do not boot due to SPL bring too large. SPL doesn't need GPIO, I2C nor MMC sector access since it uses a FAT file system. This patch unifies all these boards to remove these unused features from their defconfigs Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20configs: Add configs for J721e High Security EVMAndrew F. Davis
Add new defconfig files for the J721e High Security EVM. These defconfigs are the same as for the non-secure part, except for: CONFIG_TI_SECURE_DEVICE option set to 'y' CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y' CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y' CONFIG_BOOTCOMMAND uses FIT images for booting Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20defconfigs: am43xx_hs_evm: Sync HS and non-HS defconfigsAndrew F. Davis
Sync new additions to non-HS defconfig with HS defconfig. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20defconfigs: am335x_hs_evm: Sync HS and non-HS defconfigsAndrew F. Davis
Sync new additions to non-HS defconfig with HS defconfig. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20configs: j721e_evm_a72_defconfig: Enable I2C and EEPROM supportVignesh Raghavendra
Enable I2C and EEPROM related configs for A72 SPL/U-Boot. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20board: ti: beagleboneai: enable in am57xx_evm_defconfigCaleb Robey
Adding the configurations to the evm_defconfig file Signed-off-by: Jason Kridner <jdk@ti.com> Signed-off-by: Caleb Robey <c-robey@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20configs: j721e_evm: Add configs for environment in eMMCFaiz Abbas
Add config to save and read back environment from eMMC. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20configs: j721e_evm: Add configs for ADMA SupportFaiz Abbas
Add configs for ADMA Support. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20configs: j721e_evm_a72_defconfig: Enable USB related configsVignesh Raghavendra
Enable USB host and device related configs. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-17stm32mp1: split board and SOC support for STM32MP15x familyPatrick Delaunay
Split the board and SOC support for STM32MP15x family and prepare the introduction of new boards with STM32MP15x. This path define the 2 configurations: - STM32MP15x: STM32MP15x soc support (new) - TARGET_ST_STM32MP15x: STMicroelectronics board support (choice) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-01-17board: stm32mp1: move CONFIG_ENV_XXX in defconfigPatrick Delaunay
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig for ST board with NOR support (STM32MP15xx-EV1 boards) - CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB) - CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH) This Patch prepares the U-Boot support of boards with STM32MP15x SOC not provided by STMicroelectronics. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-01-16mx7ulp_evk: Disable CONFIG_NETFabio Estevam
Currently the following build warning is seen: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. =================================================== Since the mx7ulp-evk board does not have networking support, explicitly disable networking. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-01-16Merge tag 'mmc-1-16-2020' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
- Cleanup of fsl_esdhc driver together with arch/defconfig change - Add quirk for APP_CMD retry
2020-01-16Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Clearfog: Fix SD booting (Baruch) - Misc updates to MMC handling in SPL to support booting from main data partition (vs hardware boot partition) on MVEBU (Baruch)
2020-01-16Merge tag 'xilinx-for-v2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.04 ARM64: - Add INIT_SPL_RELATIVE dependency SPL: - FIT image fix - Enable customization of bl2_plat_get_bl31_params() Pytest: - Add test for octal/hex conversions Microblaze: - Fix manual relocation for one SPI instance Nand: - Convert zynq/zynqmp drivers to DM Xilinx: - Enable boot script location via Kconfig - Support OF_SEPARATE in board FDT selection - Remove low level uart setup it is done later by code - Add support for DEVICE_TREE variable passing for SPL Zynq: - Enable jtag boot mode via distro boot - Removing unused baseaddresses from hardware.h - DT fixups ZynqMP: - Fix emmc boot sequence - Simplify spl logic around bss and board_init_r() - Support psu_post_config_data() calling - Tune mini-nand DTS - Fix psu wiring for a2197 boards - Add runtime MMC device boot order filling in spl - Clear ATF handoff handling with custom bl2_plat_get_bl31_params() - Add support u-boot.its generation - Use single image configuration for all platforms - Enable PANIC_HANG via Kconfig - DT fixups - Firmware fixes - Add support for zcu208 and zcu1285 Versal: - Fix emmc boot sequence - Enable board_late_init() by default
2020-01-16configs: mediatek: fix mt7623n bpir2 defconfigSam Shih
This patch add CONFIG_TARGET_MT7623 into mt7623n_bpir2_defconfig to fix the mt7623 compile error after building others mediatek target platform Signed-off-by: Sam Shih <sam.shih@mediatek.com> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
2020-01-16Add support for MT7622 reference boardSam Shih
This adds a general board file based on MT7622 SoCs from MediaTek. This commit is adding the basic boot support for the MT7622 rfb. Signed-off-by: Sam Shih <sam.shih@mediatek.com> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
2020-01-16ARM: MediaTek: add basic support for MT8512 boardsmingming lee
This adds a general board file based on MT8512 SoCs from MediaTek. Apart from the generic parts (cpu) we add some low level init codes and initialize the early clocks. This commit is adding the basic boot support for the MT8512 eMMC board. Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-16arm: mvebu: clearfog: set uboot image SD card offsetBaruch Siach
Armada 38x ROM skips the first SD card offset when loading SPL. This affects the location of the main U-Boot image. SPL MMC code now supports U-Boot image offset based on run-time detection of the boot partition. Use this feature to make the same generated image support both SD card and eMMC boot partition. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2020-01-16configs: clearfog: enable SPL_DM_GPIO to fix boot from SDBaruch Siach
SPL needs DM GPIO to read the SD card-detect signal. This complements the fix in commit 70bae02f71d4 ("arm: mvebu: clearfog: fix boot from SD card"). Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2025-02-03 06:14:03 +0000