summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2018-02-04configs: Add network device support for bx50v3 productsIan Ray
Modify b450v3, b650v3 and b850v3 defconfigs to enable the network devices found in these products. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-04configs: icore: enable nand on mmc defconfigJagan Teki
Enable nand on mmc defconfig, so-that preparing nand for writing/updating bootimage, Linux becomes easy. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-02-04board: i.MX6QDL: add Engicam i.CoreM6 1.5 QDL MIPI starter kitJagan Teki
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for Android and video capture application. notable features: CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz Memory Up to 2 GB DDR3-1066 Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4 port 8 bit CSI INPUT MIPI-CSI INPUT 1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc This patch adds support for Quad/Dual and DualLite/Solo SOM's on MIPI starter kit with boot from SD and eMMC. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-02-03log: Add a way to log error-return valuesSimon Glass
When functions return an error it propagates up the stack to the point where it is reported. Often the error code provides enough information about the root cause of the error that this is obvious what went wrong. However in some cases the error may be hard to trace. For example if a driver uses several devices to perform an operation, it may not be obvious which one failed. Add a log_ret() macro to help with this. This can be used to wrap any error-return value. The logging system will then output a log record when the original error is generated, making it easy to trace the call stack of the error. This macro can significantly impact code size, so its use is controlled by a Kconfig option, which is enabled for sandbox. Signed-off-by: Simon Glass <sjg@chromium.org>
2018-02-02Kconfig: usb: rockchip: Remove not needed *_defconfig USB/gadget entriesLukasz Majewski
After moving some USB gadget configs (USB_FUNCTIONS_*) to Kconfig it turned out that following *_defconfig entries for RockChip are not needed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-02-02Kconfig: gadget: Move CONFIG_USB_FUNCTION_MASS_STORAGE to KconfigLukasz Majewski
This commit moves USB_FUNCTION_MASS_STORAGE config to Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-02-02Kconfig: gadget: Move CONFIG_USB_FUNCTION_THOR to KconfigLukasz Majewski
This commit moves USB_FUNCTION_THOR config to Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-01-31Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-01-31Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2018.03 - Several Kconfig fixes (also moving configs to defconfigs) - Some DTS updates - ZynqMP psu rework based on Zynq concept - Add low level initialization for zc770 and zcu102 - Add support for Zynq zc770 x16 nand configuration - Add mini nand/emmc ZynqMP targets - Some arasan nand changes
2018-01-30Convert CONFIG_SYS_OMAP24_I2C_SLAVE et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SYS_OMAP24_I2C_SLAVE CONFIG_SYS_OMAP24_I2C_SPEED Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
2018-01-30Convert CONFIG_SYS_DV_CLKMODE et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SYS_DV_CLKMODE CONFIG_SYS_DA850_PLL0_POSTDIV CONFIG_SYS_DA850_PLL0_PLLDIV1 CONFIG_SYS_DA850_PLL0_PLLDIV2 CONFIG_SYS_DA850_PLL0_PLLDIV3 CONFIG_SYS_DA850_PLL0_PLLDIV4 CONFIG_SYS_DA850_PLL0_PLLDIV5 CONFIG_SYS_DA850_PLL0_PLLDIV6 CONFIG_SYS_DA850_PLL0_PLLDIV7 CONFIG_SYS_DA850_PLL1_POSTDIV CONFIG_SYS_DA850_PLL1_PLLDIV1 CONFIG_SYS_DA850_PLL1_PLLDIV2 CONFIG_SYS_DA850_PLL1_PLLDIV3 Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-30armv8: ls1088a: Add CONFIG_SPI_FLASH_SPANSION to sdcard defconfigsAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-30arm64: zynqmp: Moved ethernet PHY configs of ZynqMP boards to defconfigVipul Kumar
This patch moved ethernet PHY configs of ZynqMP boards to respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30microblaze: Moved ethernet PHY configs of Microblaze board to defconfigVipul Kumar
This patch moved ethernet PHY configs of Microblaze board to respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Moved ethernet PHY configs of Zynq boards to defconfigVipul Kumar
This patch moved ethernet PHY configs of Zynq boards to respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30xilinx: zynqmp: Add new target with only emmc enabledSiva Durga Prasad Paladugu
This patch adds new target which is called as mini configuration with only emmc functionality and other required basic features enabled. This will be used to run in system with small footprint and needs emmc support. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30xilinx: zynqmp: Add new target with only nand enabledSiva Durga Prasad Paladugu
This patch adds new target which is called as mini configuration with only nand functionality and other required basic features enabled. This will be used to run in system with small footprint and needs nand support. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Enable distro defaults settingMichal Simek
BOOTCOMMAND is composed with distro_bootcmd but this variable is not present. Enabling distro defaults setting is fixing it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Move bootcommand to defconfigMichal Simek
It will cleanup generic config and enable option to change it for every board. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Enable DM_GPIO when neededMichal Simek
There are two reasons for doing this change. There is still !DM driver for xilinx soft gpio IP and especially it is saving some space for memory constrained boards like cse (almost ~400B). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Enable BLK when neededMichal Simek
There is no reason to enable BLK by default for all boards which is just increasing memory footprint for memory contrained boards like cse. zc770s are also saving some space. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Disable networking for zc770 xm011Michal Simek
Ethernet cable is not connected for xm011 that's why disable all ethernet related configurations. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Enable debug console for zc770 xm011Michal Simek
Wire debug console which is useful for early debugging. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Add identification string to Xilinx boardsMichal Simek
It is good to see this string to make sure that u-boot which runs on the board is the same which should run there. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30ARM: zynq: remove unused CONFIG_ZC770_XM01* optionsMasahiro Yamada
These are defined, but not referenced at all. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Add support for zc770-xm011-x16 configurationMichal Simek
zc770-xm011 is x8 width configuration. This FMC card has also x16 variant which requires different ps7_init configuration. This patch adds it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-28Merge git://git.denx.de/u-boot-rockchipTom Rini
2018-01-28arm: add support for PDU001Felix Brack
This patch adds support for the PDU001 board. Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-28bcm283x: Add pinctrl driverAlexander Graf
The bcm283x family of SoCs have a GPIO controller that also acts as pinctrl controller. This patch introduces a new pinctrl driver that can actually properly mux devices into their device tree defined pin states and is now the primary owner of the gpio device. The previous GPIO driver gets moved into a subdevice of the pinctrl driver, bound to the same OF node. That way whenever a device asks for pinctrl support, it gets it automatically from the pinctrl driver and GPIO support is still available in the normal command line phase. Signed-off-by: Alexander Graf <agraf@suse.de>
2018-01-28config: evb-rk3229: Enable rk gmac configsDavid Wu
Add gmac config support for rk3229 evb. Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28rockchip: configs: Enable GMAC configs for evb-rk3328David Wu
Enable GMAC configs for evb-rk3328 Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28rockchip: configs: Enable CONFIG_NET_RANDOM_ETHADDR for rk3288-evbDavid Wu
If the Ethernet address is not set, the network can't work, enable the random address config for default use. Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28configs: Replace CONFIG_ISW_ENTRY_ADDR with CONFIG_SYS_TEXT_BASEFaiz Abbas
Since 7e0ed13 ("Convert ARCH_OMAP2PLUS boards' CONFIG_SYS_TEXT_BASE to Kconfig"), a default SYS_TEXT_BASE was set for all ARCH_OMAP2PLUS devices. CONFIG_ISW_ENTRY_ADDR is used to set SYS_TEXT_BASE in qspi boot. Simplify this by directly assigning SYS_TEXT_BASE in the defconfig. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-01-28board: stm32: Add stm32f429-evaluation board supportPatrice Chotard
Add stm32f429-evaluation board support. For more information, please visit: http://www.st.com/en/evaluation-tools/stm32429i-eval.html Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-27Merge git://git.denx.de/u-boot-uniphierTom Rini
2018-01-27Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-shTom Rini
2018-01-28ARM: uniphier: enable HS200 support for uniphier_v8_defconfigMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-01-27Merge git://git.denx.de/u-boot-socfpgaTom Rini
2018-01-27ARM: rmobile: Convert R8A7791 Porter board to DM and DTMarek Vasut
Convert the R8A7791 Porter board to DM and DT. This implies mostly enabling the necessary configuration options and plucking out the ad-hoc configuration from the board file. Moreover, the pre-reloc malloc size was increased to allow the clock driver to start up early without running out of malloc space and the early stack was moved further up in the DRAM to avoid rewriting U-Boot itself. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-01-27ARM: rmobile: Enable OF_CONTROL on RCar Gen2Marek Vasut
Since the DTs are now in place, enable OF control so that they get bundled into the U-Boot. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-01-27env: Allow to build multiple environments in KconfigMaxime Ripard
Now that we have everything in place in the code, let's allow to build multiple environments backend through Kconfig. Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2018-01-26Merge git://git.denx.de/u-boot-sunxiTom Rini
2018-01-26sunxi: imply CONFIG_OF_LIBFDT_OVERLAYAndre Heider
fdt overlay support is useful for all sunxi boards, enable per default and remove it from sunxi defconfigs. Signed-off-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-26Merge git://git.denx.de/u-boot-mipsTom Rini
2018-01-26Merge git://git.denx.de/u-boot-spiTom Rini
2018-01-26MIPS: add BMIPS Comtrend AR-5315u boardÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-01-26MIPS: add BMIPS Comtrend WAP-5813n boardÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-01-25arm: socfpga: allow configs without network supportSimon Goldschmidt
Currently, socfpga_common.h does not allow configurations without network support. This is because CONFIG_CMD_PXE is defined in this file and distro mode has DHCP hard-coded as available. Fix this by moving CONFIG_CMD_PXE and CONFIG_MENU to the defconfigs and by making DHCP optional in BOOT_TARGET_DEVICES(func). Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
2018-01-24ARM: rmobile: Convert CONFIG_R8A77xx to KconfigMarek Vasut
Convert these configuration options to Kconfig, update board defconfigs and drop them from whitelist. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-01-24ARM: dts: rmobile: Factor out U-Boot extrasMarek Vasut
Pull out u-boot extras into dtsi files to make synchronization of DTS from Linux kernel as easy as a simple copy. All the U-Boot extras are now in *-u-boot.dts* files instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
generated by cgit (git 2.34.1) at 2024-12-29 04:06:13 +0000