summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2018-04-11ARM: rmobile: Add TPL support on R8A7791 M2 PorterMarek Vasut
Add and enable TPL on M2 Porter. The TPL must fit into 16 kiB due to the Gen2 BootROM restriction. The TPL is running from MERAM and is capable of performing the initial initialization of PFC, Clock, GPIO, LBSC, DBSC and QSPI NOR. DBSC is responsible for bringing up the DDR DRAM access. The TPL is capable of loading the next stage, U-Boot, from either SPI NOR or UART as a fallback. If either does provide a valid U-Boot uImage, the system stops, which allows the operator to load U-Boot ie. via JTAG and start it manually. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-04-11spl: spi: Move CONFIG_SPL_SPI_LOAD to KconfigMarek Vasut
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
2018-04-09Merge tag 'xilinx-for-v2018.05-rc2' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2018.05-rc2 - Various DT changes and sync with mainline kernel - Various defconfig updates - Add SPL init for zcu102 revA - Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX and zc1751-dc3 - Net fixes - xlnx,phy-type - 64bit axi ethernet support - arasan: Fix nand write issue - fpga fixes - Maintainer file updates
2018-04-09arm64: zynqmp: Add support for Xilinx zcu111-revAMichal Simek
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for Xilinx zcu106-revAMichal Simek
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zcu104 customer boardMichal Simek
Xilinx zcu104 is another customer board. It is sort of zcu102 clone with some differences. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zc12xx boardsMichal Simek
Add support for zc12xx boards. All of them are internal boards for silicon validation and share very similar base platforms. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zc1751 dc3Michal Simek
zc1751 is based board with dc3 extenstion card which is used for silicon validation. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zcu100 aka Ultra96 boardMichal Simek
Add support for Xilinx zcu100. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable Fixed link supportMichal Simek
This patch enables the fixed link support for all ZynqMP boards. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable mac address randomization for zc1751 dc5Michal Simek
There is no memory which stores mac address that's why generate it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable ethernet phys for zc1751 dc5Michal Simek
Enable ethernet phys for zc1751 dc5. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable booting to ATFLuca Ceresoli
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which pass control to full u-boot(EL2). This has been tested on zcu106, so enable it in this defconfig. To generate an image that triggers this booting flow, you need to pass '-O arm-trusted-firmware' to mkimage. Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09ARM: dts: zynq: Rename dts for Z-turn boardAnton Gerasimov
Makes naming in line with other Zynq boards. Signed-off-by: Anton Gerasimov <tossel@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-08Cleanup CONFIG_VERSION_VARIABLE migrationAlex Kiernan
CONFIG_VERSION_VARIABLE had already been mostly migrated to Kconfig, but two headers still referenced it. Also set defaults so that most of the defconfigs inherit the default rather than needing it to be set explicitly. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
2018-04-08Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to KconfigAlex Kiernan
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2018-04-08Migrate CONFIG_DRIVER_TI_CPSW to KconfigAlex Kiernan
This converts CONFIG_DRIVER_TI_CPSW to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-08treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_TSEC_ENET to KconfigMario Six
Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to KconfigMario Six
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08treewide: Migrate CONFIG_LAST_STAGE_INIT to KconfigMario Six
Migrate the CONFIG_LAST_STAGE_INIT option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_BOARD_EARLY_INIT_R to KconfigMario Six
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_SYS_ALT_MEMTEST to KconfigMario Six
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration after also including CMD_MEMTEST] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-06configs: am43xx_evm_qspiboot_defconfig: Move to DMVignesh R
Move am43xx_evm_qspiboot_defconfig to DM. This is required as SPI core and TI QSPI driver no longer supports non DM interfaces. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-04-06configs: k2hk_hs_evm: Resync defconfig with non-HS defconfigAndrew F. Davis
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh vutla <lokeshvutla@ti.com>
2018-04-06configs: k2e_hs_evm: Resync defconfig with non-HS defconfigAndrew F. Davis
Signed-off-by: Andrew F. Davis <afd@ti.com>
2018-04-06configs: k2g_hs_evm: Resync defconfig with non-HS defconfigAndrew F. Davis
Signed-off-by: Andrew F. Davis <afd@ti.com>
2018-04-06stm32mp1: add eMMC support for ED1Patrick Delaunay
Add command GPT support Add EMMC boot support Add the 2 other SDMMC instances for ED1: - SDMMC2 = mmc 1, eMMC on the ED1 board - SDMMC3 = extension connector, deactivated by default Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06ARM: AM43xx: Add support for RTC only + DDR in self-refresh modeTero Kristo
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers for wakeup from RTC-only mode with DDR in self-refresh. Parse these registers during SPL boot and jump to the kernel resume vector if the device is waking up from RTC-only modewith DDR in Self-refresh. The RTC scratch register layout used is: SCRATCH0 : bits00-31 : kernel resume address SCRATCH1 : bits00-15 : RTC magic value used to detect valid config SCRATCH1 : bits16-31 : board type information populated by bootloader During the normal boot path the SCRATCH1 : bits16-31 are updated with the eeprom read board type data. In the rtc_only boot path the rtc scratchpad register is read and the board type is determined and correspondingly ddr dpll parameters are set. This is done so as to avoid costly i2c read to eeprom. RTC-only +DRR in self-refresh mode support is currently only enabled for am43xx_evm_rtconly_config. This is not to be used with epos evm builds. Signed-off-by: Tero Kristo <t-kristo@ti.com> [j-keerthy@ti.com Rebased to latest u-boot master branch] Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-06am335x: am335x_evm_usbspl_defconfig: NETCONSOLEJason Kridner
Enable NETCONSOLE by default. Still requires changes to the boot environment to enable on the platform. Signed-of-by: Jason Kridner <jdk@ti.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-06Migrate CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSCAlex Kiernan
This converts CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-06board: MCR3000: cleanup configChristophe Leroy
Some config is redundant with Kconfig. Fix it. Also remove unused configs Move SDRAM_MAX_SIZE in the only place it is used include/environment.h already defines CONFIG_ENV_SIZE from CONFIG_ENV_SECT_SIZE and defines CONFIG_ENV_ADDR as (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) remove BOOTARGS as bootargs is set by the different boot commands Fix CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE to be in line with CPM DPRAM organisation Remove CONFIG_SYS_GBL_DATA_SIZE, CONFIG_SYS_GBL_DATA_OFFSET and CONFIG_SYS_INIT_SP_OFFSET which are unused Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06powerpc: mpc8xx: Change CONFIG_8xx to CONFIG_MPC8xxChristophe Leroy
CONFIG_8xx doesn't mean much outside of arch/powerpc/ This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ... It also renames 8xx_immap.h to immap_8xx.h to be consistent with other file names. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06spi: atmel: default y if DM_SPI && ARCH_AT91Jagan Teki
ATMEL_SPI is now fully converted to driver-model and respective boards switch to DM_SPI as well, so make default y for ARCH_AT91 Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Wenyou Yang <wenyouya@gmail.com>
2018-04-06at91: ma5d4evk: Enable SPL_DM and SPL_OF_CONTROLJagan Teki
Enable SPL Driver model and FDT support for AT91 ma5d4evk boards. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-04-06at91: ma5d4evk: Add FDT supportJagan Teki
Sync DTS from Linux and add FDT support for AT91 ma5d4evk board. usb0, usb1, usb2 and hlcdc_pwm nodes removed, since there is no support it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-04-06at91: vinco: Add FDT supportJagan Teki
Sync DTS from Linux and add FDT support for AT91 vinco board. usb0, usb1, and usb2 nodes removed, since there is no support it. Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-04-06configs: gurnard: Move CONFIG_ATMEL_SPI to defconfigsJagan Teki
Now CONFIG_ATMEL_SPI is defined in Kconfig, so move the same into defconfig file. Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Wenyou Yang <wenyouya@gmail.com>
2018-04-06Merge tag 'signed-rpi-next' of git://github.com/agraf/u-bootTom Rini
Patch queue for rpi - 2018-04-06 Highlights this time around: - Support for new RPi3 B+ model - Fix for some SD cards on newer RPi firmware
2018-04-05rpi3_32b: Enable lan78xx driverPeter Robinson
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add driver support in U-Boot for it. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-04-05rpi3: Enable lan78xx driverAlexander Graf
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add driver support in U-Boot for it. Signed-off-by: Alexander Graf <agraf@suse.de>
2018-04-05rpi: Allow to boot without serialAlexander Graf
When we enable CONFIG_OF_BOARD on Raspberry Pis, we may end up without serial console support in early boot. Hence we need to make the serial port optional, otherwise we will never get to the point where serial would be probed. Signed-off-by: Alexander Graf <agraf@suse.de>
2018-04-04Merge git://git.denx.de/u-boot-sunxiTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-04Revert "sunxi: Pine64: temporarily remove extra Pine64 non-plus DT"Andre Przywara
Now with the MMC environment gone, we have enough space to accommodate the Pine64 "non-plus" .dtb again. This reverts commit 47952b8e42c2790150e16d3d4235b3a1ee0ba9bb. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-03configs: add NAND support for NES ClassicMiquel Raynal
Add NAND parameters to the Nintendo NES Classic configuration file which features a Macronix NAND flash chip with 128kiB blocks of 2kiB pages plus 64 OOB bytes. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03sunxi: move the NAND parameters to KconfigMiquel Raynal
Move the NAND parameters from defconfig files to Kconfig for SUNXI architecture only. Fort now only the CHIP pro is migrated. It would have been better to convert this defconfig entry to Kconfig for all supported machines/architectures but it has been abandoned due to a fairly high amount of errors reported by the moveconfig.py tool. This is due to defines quite often being multiplications of values/other defines not correctly handled. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03sunxi: make NAND_SUNXI use ARCH_SUNXI as default in KconfigMiquel Raynal
Remove NAND_SUNXI from the CHIP pro defconfig to be automatically selected depending on the state of ARCH_SUNXI. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03sunxi: automatically select SPL_NAND_SUPPORT in KconfigMiquel Raynal
Make SUNXI_NAND select SPL_NAND_SUPPORT in Kconfig, this limit the number of entries to add in defconfig files when adding NAND support. For now, the only board using it is the CHIP pro. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-02ARC: HSDK: Enable SPI flash supportEugeniy Paltsev
HSDK board has sst26wf016 SPI flash IC which we want to support. Add SPI controller, CS-gpio and SPI flash nodes to hsdk device tree. Enable corresponding options in hsdk defconfig. For SPI write functionality to work we need [1] which adds support of sst26xxx ICs. [1] https://patchwork.ozlabs.org/project/uboot/list/?series=35796 Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
generated by cgit (git 2.34.1) at 2025-01-09 16:27:44 +0000