Age | Commit message (Collapse) | Author |
|
Enable Secure boot(HAB) for BTicino Mamoj board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add Falcon mode support to boot Linux directly after SPL.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add DFU support for BTicino Mamoj board and update
the same steps in README.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
|
|
Enable fastboot and ums for host to interact eMMC on
Mamoj board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
|
|
MX6DL Mamoj boards has Freescale PFUZE100 PMIC, add support
for it through DM_PMIC dt definition.
pmic log:
Reviewed-by: Stefano Babic <sbabic@denx.de>
========
=> pmic list
| Name | Parent name | Parent uclass @ seq
| pfuze100@08 | i2c@021f8000 | i2c @ 3
=> pmic dev pfuze100@08
dev: 0 @ pfuze100@08
=> pmic dump
Dump pmic: pfuze100@08 registers
0x00: 10 00 00 21 00 01 3f 01 00 7f 00 00 00 00 00 81
0x10: 00 00 3f 00 00 00 00 00 00 00 00 10 00 00 00 00
0x20: 2b 2b 2b 08 c4 00 00 00 00 00 00 00 00 00 2b 2b
0x30: 2b 08 c4 00 00 72 72 72 08 d4 00 00 2c 2c 2c 08
0x40: e4 00 00 2c 2c 2c 08 e4 00 00 6f 6f 6f 08 f4 00
0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x60: 00 00 00 00 00 00 48 00 00 00 10 06 1e 1e 17 10
0x70: 1a 1f 00 00 00 00 00 00 00 00 00 00 00 00 00
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
|
|
i.MX6DL Mamoj has i2c3 and i2c4 buses, add support
through DM_I2C with dt definition.
i2c log:
Reviewed-by: Stefano Babic <sbabic@denx.de>
=======
=> i2c bus
Bus 2: i2c@021a8000
Bus 3: i2c@021f8000
=> i2c dev 2
Setting bus to 2
=> i2c speed 400000
Setting bus speed to 400000 Hz
=> i2c probe
Valid chip addresses: 20 51 53
=> i2c md 53 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
=> i2c md 51 0xff
00ff: a8 08 40 50 09 43 46 52 42 18 80 8e ae a9 d0 53 ..@P.CFRB......S
=> i2c dev 3
Setting bus to 3
=> i2c speed 100000
Setting bus speed to 100000 Hz
=> i2c probe
Valid chip addresses: 08 40 48 4B
=> i2c md 08 0xff
00ff: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
|
|
Add initial support for i.MX6DL BTicino Mamoj board.
Mamoh board added:
- SPL
- SPL_DM
- SPL_OF_CONTROL
- DM for U-Boot proper
- OF_CONTROL for U-Boot proper
- eMMC
- FEC
- Boot from eMMC
- Boot from USB SDP
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Boot tested with boot.scr script and EFI/Grub2 on mmc0 and mmc1 slots on sabrelite board.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
|
|
CONFIG_ENV_IS_IN_MMC must be declared in defconfig to properly
support "env save".
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce
necessary Kconfig changes as well.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This replaces TARGET_GE_B{4,6,8}50V3 with common TARGET_GE_BX50V3.
The boards are identified automatically at runtime.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
Add winbond SPI NOR support, which is being used by newer hardware.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
This was unintentionally disabled when moving MVGBE to Kconfig.
Fixes: commit ed52ea507f12 ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
|
|
Add Kconfig for MVGBE and update boards to select this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add a Kconfig option for BOOTP_NTPSERVER to enable the DHCP/BOOTP option
to configure the sntp server address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards
already had it in their Kconfig), but had not been moved for older
boards.
Move it to the defconfigs for all boards.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This adds basic support for the Turris Mox board from CZ.NIC, which is
currently being crowdfunded on Indiegogo.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic module can be extended by different modules. The device tree
binary for the kernel can be dependent on which modules are connected,
and in what order. Because of this, the board specific code creates
in U-Boot a variable called module_topology, which carries this
information.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Since now we have driver for clocks on Armada 37xx, use it to determine
SQF clock frequency for the SPI driver.
Also change the default config files for Armada 37xx devices so that
the clock driver is enabled by default, otherwise the SPI driver cannot
be enabled.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
|
|
|
|
This patch enables UHS support for ZynqMP zcu102 rev 1.0
board.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
DISPLAY_BOARDINFO in OF case show model identification string from DT.
Enable this feature instead of custom IDENT_STRING which does the same
thing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
|
|
Enable watchdog on zcu100 to make sure if there is a bug in the u-boot
there is proper reset.
Watchdog expires and PMU fw is informed and based on setting proper
action is taken.
The patch is enabling reset-on-timeout feature and also fixing fixed
clock rate for watchdog where 100MHz is max (and also default) clock value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch removes UBI support from defconfig and it can
be enabled from menuconfig as per need.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Now that showing silicon version is part of the CPU
info display, let's remove checkboard().
Note that the generic show_board_info() will still
show the DT 'model' property. For instance:
U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)
CPU: Zynq 7z045
Silicon: v1.0
Model: Zynq ZC706 Development Board
I2C: ready
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>,
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mini configuration doesn't need to show this information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The boot count is enabled in both SPL and proper u-boot.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Enable CONFIG_MTD as well to make sure UCLASS_MTD is available
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
U-Boot on Harmony recently got broken by ongoing driver model resp. live
tree migration work:
U-Boot 2018.03-rc3 (Feb 21 2018 - 15:43:08 +0100)
TEGRA20
Model: NVIDIA Tegra20 Harmony evaluation board
Board: NVIDIA Harmony
DRAM: 1 GiB
Video device 'dc@54200000' cannot allocate frame buffer memory -ensure
the device is set up before relocation
Error binding driver 'tegra_lcd': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 3ffa86d0 failed at call 00121dc0 (err=-28)
This commit fixes this by enabling live tree, MTD and UBI for Harmony as
well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
|
|
Enable vrefbuf on stm32mp15, to be used by ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Enable DM_REGULATOR_STPMU1 flag to activate regulator
driver for STM32MP15 SoC and CMD_REGULATOR flag to be
able to set/get regulator state int U-boot command line.
Disable PMIC_CHILDREN as this flag is not needed in SPL
for STM32MP1.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Remove SYS_USE_NANDFLASH, SYS_USE_MMC as they are deprecated and
unused.
The board configurations already use CONFIG_SD_BOOT and
CONFIG_NAND_BOOT respectively.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[eugen.hristev@microchip.com: rework on latest u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
We have a new demo layout of our sama5 boards for the NAND Flash
memory.
According to this new layout, adjust the mtdparts variable in bootargs
to align with this, which is available at :
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map,
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Enable the CONFIG_DM_REGULATOR_MAX77686 for using regulator driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Enable the pin configuration feature for UniPhier 64 bit SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Banana Pi BPI-M2 Berry is a quad-core mini single board computer
built with Allwinner V40 SoC. It features
- Quad Core ARM Cortex A7 CPU V40
- 1GB of RAM .
- microSD/SATA port..
- onboard WiFi and BT
- 4 USB A 2.0 ports
- 1 USB OTG port
- 1 HDMI port
- 1 audio jack
- DC power port
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Convert the symbol to Kconfig, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This patch adds a device tree file for the H5 version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe27544125e ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H5 SoC, and
has 4Gb DDR3 chips instead of 2Gb ones.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This patch adds a device tree file for the H2+ version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe27544125e ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H2+ SoC, and
has only two 2Gb DDR3 chips instead of four.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The Libre Computer Board ALL-H3-CC does not have an I2C controllable
regulator. Having R_I2C and SPL_I2C enabled serves no purpose.
Disable them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
|
|
CONFIG_SPL_SERIAL_SUPPORT had already been migrated to Kconfig, but
existed in some include files; fix those up here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|