summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2020-05-19configs: nxp: Enable CONFIG_SYS_RELOC_GD_ENV_ADDRKuldeep Singh
Commit 323d3af59fe4 ("configs: ls1012ardb: Enable CONFIG_SYS_RELOC_GD_ENV_ADDR") enables the config only for LS1012ARDB. Apart from LS1012A-RDB, other platforms such as LS1012A-FRWY, LS2088A and LS1046A-RDB/FRWY also require this config to be enabled. This also helps in resolving booting crash observed in flash environment. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls1012a: Reduce CONFIG_ENV_SIZE to 0x2000Ashish Kumar
All LS1012A board variants have same CONFIG_ENV_SECT_SIZE and CONFIG_ENV_SIZE values. If both config values are same, flash environment cannot be saved. Since, CONFIG_ENV_SECT_SIZE needs to be same as that of flash sector size, this entry cannot be changed. Reduce CONFIG_ENV_SIZE value to 0x2000. This also helps in making config value aligned with other boards environemt size. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: Ashish Kumar <Ashish.kumar@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls1046a: Define ENV_ADDR valueKuldeep Singh
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init. The macro value is already defined in ls1046ardb_tfa_defconfig, also define the value as 0x40300000 in qspi_defconfig. ls1046aqds has one spansion flash "S25FL128S_64K" of size 16M with sector size 64K. Correct ENV_ADDR and ENV_SECT_SIZE value for QSPI and TFA defconfigs of the board. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls2080a: Correct ENV_ADDR valueKuldeep Singh
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init. QSPI region in LS2088ARDB and LS2088AQDS starts from 0x20000000 offset. Correct the config value i.e 0x80500000 -> 0x20500000. Also, define config value as 0x20300000 in qspi defconfig. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls1088a: Correct ENV_ADDR valueKuldeep Singh
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init. QSPI region starts from 0x20000000 offset. Correct the config value i.e 0x80500000 -> 0x20500000. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls1046a: Move SPI_FLASH_SPANSION to defconfigKuldeep Singh
Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and LS1046AQDS which have two spansion flases i.e s25fs512s each of size 64M. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls1012a: Enable CONFIG_SPI_FLASH_SPANSION in defconfigsKuldeep Singh
Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion flashes. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls1043a: Move CONFIG_FSL_QSPI and SPI_FLASH_SPANSION to defconfigKuldeep Singh
Move CONFIG_FSL_QSPI to the board defconfigs and while at it also move CONFIG_SPI_FLASH_SPANSION for LS1043AQDS. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-17configs: lx2160a: Add default config for lx2160a using StMM in OP-TEEIlias Apalodimas
Previous patches allow UEFI secure variables to be stored in an RPMB device using OPTEE. Add a config for the lx2160a hardware so the feature gets at least compiled. Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Remove superfluous differences to lx2160ardb_tfa_defconfig. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-05-15qemu-x86*_defconfig: Enable CONFIG_PCI_INIT_ROvidiu Panait
Enable CONFIG_PCI_INIT_R for qemux86 and qemux86-64 pci enumeration during boot in order to eliminate the custom preboot commands in include/configs/qemu-x86.h. Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2020-05-15qemu_arm_defconfig: Enable CONFIG_PCI_INIT_ROvidiu Panait
Replace the "pci enum" preboot sequence with CONFIG_PCI_INIT_R=y. Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2020-05-15qemu_arm64_defconfig: Enable CONFIG_PCI_INIT_ROvidiu Panait
Replace the "pci enum" preboot sequence with CONFIG_PCI_INIT_R=y. Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2020-05-15configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-15rename symbol: CONFIG_STM32 -> CONFIG_ARCH_STM32Trevor Woerner
Have this symbol follow the pattern of all other such symbols. Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15rename symbol: CONFIG_TEGRA -> CONFIG_ARCH_TEGRATrevor Woerner
Have this symbol follow the pattern of all other such symbols. Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15rename symbol: CONFIG_KIRKWOOD -> CONFIG_ARCH_KIRKWOODTrevor Woerner
Have this symbol follow the pattern of all other such symbols. This patch also removes a TODO from the code. Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15arm: orion5x: finish moving SoC to mach-orion5xTrevor Woerner
The SPL linker script had been left in arch/$(ARCH)/cpu/$(CPU)/$(SOC); therefore move it to the already-established arch/$(ARCH)/mach-$(SOC) location. Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15rename symbol: CONFIG_ORION5X -> CONFIG_ARCH_ORION5XTrevor Woerner
Have this symbol follow the pattern of all other such symbols. This patch removes a TODO from the code. Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15configs: mt7629: support usb host and udiskChunfeng Yun
Enable modules to support download image from usb Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
2020-05-14Merge tag 'u-boot-stm32-20200514' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - stm32mp1: migrate MTD and DFU configuration in Kconfig - stm32mp1: add command stm32prog - stm32mp1: several board and arch updates - stm32mp1: activate data cache in SPL and before relocation - Many improvment for AV96 board and DHCOR SoM (add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM) - clk: stm32mp1: fix CK_MPU calculation - DT alignment of stm32mp1 device tree with Linux 5.7-rc2
2020-05-14Merge tag 'rpi-next-2020.07' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi - fix phy configuration for RPi4's bcmgenet - sync RPi4's env size with other RPi configs - add kconfig option to reserver more pages in the EFI mem map - add support for SDMA which is used by RPi4 - fix corner case boot bug for RPi3 32-bit
2020-05-14ARM: stm32: Hog GPIO PF7 high on DHCOM to unlock SPI NOR nWPMarek Vasut
The SPI NOR nWP line is connected to GPIO PF7 on the SoM, pull the GPIO line high by default to clear SPI NOR WP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-14ARM: stm32: Define I2C EEPROM bus and address on DHCOMMarek Vasut
Define I2C EEPROM bus and address, so that the 'eeprom' command uses the correct ones and does not generate the following error: eeprom_rw_block: Cannot find udev for a bus 0 Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-14configs: stm32mp1: activate CONFIG_ERRNO_STRPatrick Delaunay
Add support of errno_str, used in command pmic and regulator. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14configs: stm32mp1: activate Ethernet PHY RealtekChristophe Roullier
Need Realtek driver to manage in RTL8211F the configuration of the LED. Initialize LCR (LED Control Register) to configure green LED for Link, yellow LED for Active Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-14stm32mp: stm32prog: add MTD devices supportPatrick Delaunay
Add support of MTD device (DFU_MTD backend) for NOR, NAND or SPI-NAND target. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp: stm32prog: add MMC devicePatrick Delaunay
Add support of MMC device (based on DFU_MMC backend) for SD card and eMMC update. Create a GPT partitioning on the device. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp: add the command stm32progPatrick Delaunay
Add a specific command stm32prog for STM32MP soc family witch allows to program the boot devices with the tool STM32CubeProgrammer (http://www.st.com/STM32CubeProg). This command uses the same UART STM32 protocol than MCU STM32 with or USB with DFU protocol v1.1 (ithe MCU ST extension are no supported). The executed actions are based on a tab separated value file with a stm32 header, the FlashLayout file (https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout). This file is parsed by the U-Boot command to: - initialize the devices - create the partition table on each device - initialize the DFU backend to access to not volatile memory (NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC) Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout. The communication between U-Boot and STM32CubeProgrammer is done with the specific alternate configuration (see "AN5275: USB DFU/USART protocols used in STM32MP1 Series bootloaders" for details). The command stm32prog is executed when a boot from USB is detected (selected with bootpins) and we can program the boot devices with a simple command (on Windows or Linux): PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv 1/ the ROM code loads TF-A in embedded RAM (DFU or uart) 2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart) 3/ U-Boot executes the stm32prog command (DFU or uart) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14configs: stm32mp1: remove optee defconfigPatrick Delaunay
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig is identical to stm32mp15_trusted_defconfig and can be removed. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14stm32mp1: dynamically detect op-tee presencePatrick Delaunay
Activate OP-TEE driver for trusted and optee defconfig. This driver allows detection of TEE presence for boot from flash; CONFIG_STM32MP1_OPTEE is also removed. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14ARM: stm32: Implement board coding on AV96Marek Vasut
The AV96 board does exist in multiple variants. To cater for all of them, implement board code handling. There are two GPIOs which code the type of the board, read them out and use the value to pick the correct device tree from an fitImage. Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
2020-05-14ARM: stm32: Add default config for DHCORMarek Vasut
Add default U-Boot configuration for the DHCOR SoM on AV96 board. Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-05-13configs: rpi_arm64: enable SDHCI SDMA supportMatthias Brugger
RPi4 supports SDMA on it's SDHCI controller. Enable to option for the combine RPi3/4 config. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-05-12Merge tag 'u-boot-amlogic-20200511' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - Enable USB Host for Odroid-C2 board - Add Open-Drain/Open-Source emulation in GPIO uclass
2020-05-12configs: rpi_arm64: sync env size with rpi_{3,4}_defconfigMarek Szyprowski
Use the same environment size as the configs dedicated for rpi3 and rpi4. This allows to switch between the builds and not to loose the settings stored on the SD card. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-05-12configs: rpi_4 : enable SDHCI_SDMA configJaehoon Chung
Enable SDHCI_SDMA configuration. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-05-11Merge tag 'ti-v2020.07-rc2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-ti - Fix boot issues on Nokia RX-51 - Configure AM6 CPSW for 10Mbps in rgmii mode. - Minor changes for J721e
2020-05-11odroid-c2: enable USB host controllerBeniamino Galvani
Enable the second USB controller, which is connected to a hub with 4 ports. The first controller is for the OTG port and is currently not supported. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> [narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-05-11Nokia RX-51: Disable some unused features to decrease size of u-boot binaryPali Rohár
Maximal allowed size of U-Boot binary for Nokia N900 is just 262144 bytes. Signed-off-by: Pali Rohár <pali@kernel.org>
2020-05-11Nokia RX-51: Enable CONFIG_CONSOLE_MUXPali Rohár
After this change both device display and serial console would contain U-Boto output automatically without any future configuration. This would allow easier debugging on real device as access to serial console is hard and also in qemu emulator where it is easier to copy+paste from serial console as from SDL framebuffer. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-05-11Nokia RX-51: Revert back onenand defitionsPali Rohár
In commit commit 43ede0bca7fc ("Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT") were removed definitions for onenand partitions. Revert them back and enable needed options for onenand support. Signed-off-by: Pali Rohár <pali@kernel.org>
2020-05-11Nokia RX-51: Move code from defconfig back to C header filePali Rohár
In commit commit 37304aaf60bf ("Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig") was moved complicated multiline script code from C header to oneliner in defconfig. After this change multiline to wide oneliner it is hard to read this code and even harder to debug. Moreover this script code should be at place where are other scripts, so move it back to C header file. Define new env variable preboot which stores this script and in option CONFIG_PREBOOT calls this preboot variable. Signed-off-by: Pali Rohár <pali@kernel.org>
2020-05-10imx: Add support for i.MX8MM Beacon EmbeddedWorks devkit.Adam Ford
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing a devkit based on the i.MX8M Mini SoC consisting of baseboard + SOM. It supports eMMC on the SOM, microSD on the baseboard, various GPIO, the PINCTRL, and UART. Signed-off-by: Adam Ford <aford173@gmail.com>
2020-05-10imx8mq_phanbell: Run SPL with caches enabledFabio Estevam
It is safe to run SPL with caches enabled on i.MX8M, so remove such restriction. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-05-10ARM: imx: pico-imx8mq: Add support for Technexion Pico-iMX8MQMarek Vasut
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier board. Currently working is ethernet, serial, eMMC. DT is imported from Linux 5.4.28 ("462afcd6e7ea") . Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08treewide: mem: Enable MEMTEST via defconfigMichal Simek
There is no reason to enable MEMTEST from headers when was converted to Kconfig already. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-05-08configs: migrate CONFIG_SYS_MTDPARTS_RUNTIME to defconfigsPatrick Delaunay
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-08configs: migrate CONFIG_SET_DFU_ALT_INFO to defconfigsPatrick Delaunay
Move CONFIG_SET_DFU_ALT_INFO into Kconfig done by moveconfig.py. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-05-08configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>