summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2019-10-08ARM: Update display5_factory_defconfig after switch to DM/DTS and uuu utilityLukasz Majewski
This commit updates the display5_factory_defconfig file after the switch to DM/DTS for this board. Moreover, the VID and PID for SPL running SDP gadget have been updated to allow seamless work with 'uuu' utility from NXP (the imx_usb doesn't work properly after embedding the u-boot proper into fitImage - problem with IVT embedding in FIT). Example to use 'uuu' session: cat << EOF > display5_recovery.lst uuu_version 1.2.135 SDP: boot -f /srv/tftp/SPL SDPU: write -f /srv/tftp/u-boot-dtb.img -addr 0x10000000 SDPU: jump -addr 0x10000000 SDPU: done EOF sudo ./uuu/uuu display5_recovery.lst Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: WDT: Convert WDT driver to use DM/DTS (including SYSRESET)Lukasz Majewski
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover, the SYSRESET_WATCHDOG driver is used to support 'reset' command. As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is enabled for it. This allows the legacy SPL code to work properly. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL)Lukasz Majewski
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not supported as of time of this conversion. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08ARM: imx: defconfig: Enable 'regulator' and 'pmic' commands on display5Lukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: I2C: Switch display5 board to use DM_I2CLukasz Majewski
After this commit the display5 device would use I2C driver supporting driver model (DM_I2C). The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize on-bus devices according to device tree description. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08ARM: imx: defconfig: Enable CONFIG_PINCTRL{_IMX6} on display5's defconfigLukasz Majewski
Enable PINCTRL for i.MX6 soc based display5 after DM/DTS conversion. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08fix: defconfig: Enable OF_CONTROL for display5_factoryLukasz Majewski
This change fixes issue with building display5 "factory" U-Boot variant when the display5 board gains DM/DTS support. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08pico-imx6: Add splashscreen supportFabio Estevam
Add splashscreen support. Tested with the parallel FT5x06-WVGA panel. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Fix bootmenu handlingOtavio Salvador
We should use a common script to allow booting the U-Boot console as fallback so we ended using a 'default_boot' and 'base_boot' environment scripts to accomplish that. Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add initial supportFabio Estevam
Add the initial support for the pico-imx6 variants. DDR initialization is based on the TechNexion's U-Boot code. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08board: imx6dl_mamoj: set the value for CSF sizeStefano Babic
Default value is too high and it covers the worst case. SPL for imx6dl_mamoj becomes too big and cannot fit into the OCRAM, but CSF size can be reduced. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Jagan Teki <jagan@amarulasolutions.com> CC: Breno Lima <breno.lima@nxp.com>
2019-10-08configs: Sync all baseboard specific pico-imx7dOtavio Salvador
This syncs all baseboard specific defconfig using the pico-imx7d_defconfig as base. It changes: - pico-dwarf-imx7d_defconfig - pico-hobbit-imx7d_defconfig - pico-nymph-imx7d_defconfig - pico-pi-imx7d_defconfig Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08configs: pico-imx7d: Convert to DM_VIDEOJoris Offouga
This commit convert all pico-imx7d to DM_VIDEO Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-10-08imx: sksimx6_defconfig: remove SPL misc option to fix build errorAnatolij Gustschin
Remove CONFIG_SPL_DRIVERS_MISC_SUPPORT since it is already defined in include/configs/mx6_common.h for SPL builds. When this option is in defconfig, we get build warnings (or errors when building with -Werror). Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-10-08pico: Convert to CONFIG_FSL_USDHCFabio Estevam
The eSDHC config symbol has been converted to CONFIG_FSL_USDHC, so adjust it accordingly in order to fix the build errors: https://travis-ci.org/sbabic/u-boot-imx/jobs/584781580#L1287 Reported-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-10-08pico-imx7d: Add NYMPH baseboard supportOtavio Salvador
This add the boot menu option for the NYMPH baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx7d: Add DWARF baseboard supportOtavio Salvador
This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx7d: Sync pico-hobbit-imx7d_defconfigFabio Berton
Update pico-hobbit-imx7d_defconfig using pico-imx7d_defconfig as base to fix device tree file generation. With this all pico-imx7d are creating u-boot-dtb.img files. Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
2019-10-08pico-imx6ul: Add LCD supportFabio Estevam
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Add DWARF baseboard supportOtavio Salvador
This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08configs: imx8qm/qxp_mek: enable CONFIG_OF_SYSTEM_SETUPPeng Fan
Enable CONFIG_OF_SYSTEM_SETUP to let U-Boot could disable device tree nodes that could not be used by Linux. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8qm_mek: switch to use container imagePeng Fan
Because FIT could not be used for AHAB secure boot on i.MX8, so switch to use container image that could let SPL verify ATF and U-Boot with AHAB. Enable HUSH_PARSER in defconfig to make run netboot could work. Note: The AHAB related code has not been added. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8qxp_mek: switch to use container imagePeng Fan
Because FIT could not be used for AHAB secure boot on i.MX8, so switch to use container image that could let SPL verify ATF and U-Boot with AHAB. Note: The AHAB related code has not been added. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6sabresd: fix usb start when DM enabledPeng Fan
Enable CONFIG_DM_REGULATOR_FIXED to let vbus regulator work. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08Kconfig: Migrate CONFIG_CSF_SIZE to KconfigBreno Matheus Lima
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000. mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08mx6sabresd: Reduce overall SPL sizeFabio Estevam
Currently the SPL binary is 67 kB, which leaves only 1 kB of free internal RAM space. The following options can be safely removed to save some precious SPL space: - CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd command (at offset 69 kB) - CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL - CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported by default After this change the SPL binary size gets down to 51 kB. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Enable fuse comamndPeng Fan
Enable fuse command Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix wrong i2c configuration nameYe Li
Wrong I2c driver configuration name is used in codes, so I2c driver is not built. Correct it. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb bootPeng Fan
Since the SD3.0 kernel driver needs M4 image support, this causes problem for usb boot booting into kernel. To decouple the relationship, we modify the FDT file in u-boot to disable SD3.0. So the kernel won't depend on M4 image. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08configs: nitrogen6x: Add DM_SPI/DM_SPI_FLASH supportTroy Kisky
Add CONFIG_DM_SPI/CONFIG_DM_SPI_FLASH to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_GPIO supportTroy Kisky
Add CONFIG_DM_GPIO to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This is in preparation for adding CONFIG_DM_SPI. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_MMC/DM_USB/AHCI supportTroy Kisky
Add DM_MMC to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This commit is adding multiple configs, but seems to be the minimum change to not lose features and still compile fine. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08nitrogen6x: migrate to using device treeTroy Kisky
Migrate to using device tree required for further driver model integration. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08imx: mx6slevk: enable DM_SPI and DM_SPI_FLASHPeng Fan
With DM_SPI and DM_SPI_FLASH enabled, we could get: spi 0 [ ] mxc_spi | | | `-- ecspi@02008000 spi_flash 0 [ ] spi_flash_std | | | `-- m25p80@0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6ul_14x14_evk: convert to DM_VIDEOPeng Fan
To support DM_VIDEO, Add display node for lcdif Drop board iomuxc settings. Enable DM_VIDEO Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08imx: add i.MX6ULZ boardPeng Fan
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible with i.MX6ULL. so most code of i.MX6ULL can be reused by i.MX6ULZ. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08arm64: versal: remove debug uart for versal virtIbai Erkiaga
Remove the debug uart configuration from versal virtual defconfig. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Introduce virtual defconfigIbai Erkiaga
Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Introduce virtual defconfigIbai Erkiaga
Add virtual defconfig for ZynqMP architecture using of_board dtb. This defconfig should become generic config for all ZynqMP boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Enable clock driverMichal Simek
Enable clock driver for Versal. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Enable random mac generationMichal Simek
In case that mac address is not found it is generated randomly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Enable cache by defaultMichal Simek
The whole cache code needs to be redesign to read information about cache from DT instead of macro selection. Enable caches by default because systems have caches on by default for Linux. Also enable CMD_CACHE to be able to disable cache if there is any issue. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Define default SYS_PROMPTMichal Simek
All boards are using the same prompt that's why add it as default value to Kconfig to simplify defconfigs. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2019-10-08ARM: zynq: Define default SYS_PROMPTMichal Simek
All boards are using the same prompt that's why add it as default value to Kconfig to simplify defconfigs. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add a2197 memory board revAMichal Simek
Similar to processor board but i2c structure is completely different. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add System Controller for a2197-g/pMichal Simek
Similar SCs but different wiring. - dc_i2c is connected to X-PRC cards that's why label is required to have an option to hook up some devices. - Exactly identify i2c devices on x-prc boards. In case of missing i2c connection devices won't be accessible. - USB 0 should be device mode with super speed. - USB 1 should be host mode. - Fix i2c mux reset pin entry - commented, not verified. - Fix i2c1 eeprom compatible string - it is an ST 128Kbit device. Need to use atmel fallback. - Fix si570 I2C slave address and add corresponding part numbers. - Enable AMS for system monitoring. - phy reset property should be commented because it will throw a warning dump when called from context that can sleep. No support for phys property (zynqmp phy driver) with SGMII. Add is-internal-pcspma property required by uboot. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
2019-10-08arm64: zynqmp: Add generic a2197 system controller configMichal Simek
Add generic configuration for a2197-p/-m/-g boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Remove unneeded configs for mini configurationsSiva Durga Prasad Paladugu
The PSCI_RESET and EXPERT are not needed for mini configurations so remove them to save space. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: mini_emmc: Enable fatwrite supportSiva Durga Prasad Paladugu
This patch enable fatwrite support for mini emmc configurations. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
2019-10-08arm64: zynqmp: Enable 2 NAND chips support for zynqmp_mini_nandT Karthik Reddy
This patch enables 2 nand chips support for zynqmp mini nand Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-25 11:53:02 +0000