| Age | Commit message (Collapse) | Author |
|---|
|
Enable this feature on chromebook_coral to speed up the display.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from 1830ms to 62ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add missing includes.
Add CMD_LSBLK to sandbox_defconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
At this point in time we can now remove our legacy code and switch to
enabling DM for USB and Ethernet.
Cc: Derald D. Woods <woods.technical@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
|
|
There are two options that are currently whitelisted, but they
are redundant, because there are not necessary since Kconfig options
exist to basically state the same thing.
CONFIG_DIRECT_NOR_BOOT and CONFIG_USE_NOR are both set together and
only used by the da850 when booting from NOR, however the only time
CONFIG_MTD_NOR_FLASH is configured is when booting from NOR. Since
NOR doesn't need SPL, the options for SPL can be moved to a check for
building SPL instead of checking for NOR.
This patch removes the checks for these two config options and unifies
the checks around the Kconfig option of CONFIG_MTD_NOR_FLASH.
Since this board is the only board that uses these two config options,
they can be removed from the whitelist table.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
- Enable DM_SPI on siemens omap boards (Jagan)
- Dropped some non-dm supported omap3 boards (Jagan)
- Dropped non-dm code in omap3 spi driver (Jagan)
- Dropped non-dm code in kirkwood spi driver (Bhargav)
|
|
I actually do not see this used these days because eMMC or NAND is used
for non-volatile devices. Dump the burden to maintain this crappy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, the supports for the following two ARMv7 SoC groups
are exclusive, because the boot ROM loads the SPL to a different
address:
- LD4, sLD8 (SPL is loaded at 0x00040000)
- Pro4, Pro5, PXs2, LD6b (SPL is loaded at 0x00100000)
This limitation exists only when CONFIG_SPL=y.
Instead of using crappy CONFIG options, checking SPL and SPL_TEXT_BASE
is cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- add support for PCI and XHCI for RPi4 (64 bit only)
- optionally reset XHCI device on registration
- enable USB_KEYBOARD for rpi_4_defconfig
|
|
This requires enabling BRCMSTB PCIe and XHCI_PCI drivers as well as PCI
and USB commands. To get it working one has to call the following commands:
"pci enum; usb start;", thus such commands have been added to the default
"preboot" environment variable. One has to update their environment if it
is already configured to get this feature working out of the box.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Move ADDR_MAP related config options from include/configs/*.h to the
proper place in lib/Kconfig. This has been done using
./tools/moveconfig.py and manual inspection of the generated changes.
This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4
board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity
mapping limit.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Supporting USB keyboards out of the box is both handy for development
and production. Notably if u-boot is used to boot into GRUB.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[mb: drop rpi_4_32b_defconfig hunk]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
|
|
This is required in order to access the reset controller used to
initialize the board's xHCI chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
|
|
This requires enabling BRCMSTB PCIe and XHCI_PCI drivers as well as PCI
and USB commands. To get it working one has to call the following commands:
"pci enum; usb start;", thus such commands have been added to the default
"preboot" environment variable. One has to update their environment if it
is already configured to get this feature working out of the box.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
|
|
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI, DM_SPI_FLASH for db-88f6281-bp-nand board.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Gilles Gameiro <gilles@gigadevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Ash Charles <ash@gumstix.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI, DM_SPI_FLASH for siemens rut board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI, DM_SPI_FLASH for siemens pxm2 board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI, DM_SPI_FLASH for siemens thuban board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI, DM_SPI_FLASH for siemens rastaban board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI, DM_SPI_FLASH for siemens etamin board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI, DM_SPI_FLASH for siemens draco board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable DM_SPI for am355x igep003x board.
Build is fine, but not tested.
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
- Add two- and three-argument versions of CONFIG_IS_ENABLED in
linux/kconfig.h
- Adds a new feature which supports copying modified parts of
the frame buffer to the uncached hardware buffer
- Enable the copy framebuffer on various x86 targets
|
|
i2c changes for v2020.10
- Add support for I2C controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
- Add I2C controller support for Cortina Access CAxxxx SoCs
- new rtc methods, rtc command, and tests
- imx_lpi2c: Improve the codes to use private data
- stm32f7_i2c.c: Add new compatible "st,stm32mp15-i2c"
- stm32f7_i2c.c: Add Fast Mode Plus support
- pwm: Add PWM driver for SiFive SoC
|
|
This patch enables DM_ETH for the following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This patch enables DM_USB and USB_STORAGE for the following
Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This patch switches the SATA driver from mvsata_ide to sata_mv for the
following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This patch converts the following Kirkwood-based LaCie boards to DM,
DM_SPI and DM_SPI_FLASH:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This seems like a more reasonable resolution for this board, since it is
quite slow. It also allows it to work with a 5" LCD display in my lab.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Update the video driver to support this feature and enable it on
minnowmax to speed up the display.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from over 13 seconds to
300ms, at 1280x1024.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Update the video driver to support this feature and enable it on link.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 930ms to 29ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Update the video driver to support this feature and enable it on samus.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 430ms to 12ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Enable this feature on sandbox by updating the SDL driver to have two
framebuffers.
Update the video tests to check that the copy framebuffer is kept in sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
In order to allow adding unit tests of the rtc command, add it to the
various sandbox defconfigs.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
|
|
Add I2C board support for Cortina Access Presidio Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Add proper Odroid-N2 board support code
- Add support for Odroid-C4 single board computer
|
|
commit 2bd261dd1712 ("gpio: search for gpio label if gpio is not found through bank name")
disabled DM_GPIO_LOOKUP_LABEL which is needed
in sandbox defconfigs, as we have tests for this
functionality.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
|
|
Add a proper Odroid-N2 board support to handle the Ethernet MAC
address stored in the in-SoC eFuses.
Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- dts sync from kernel for rk3399 boards;
- Add Radxa Rock Pi N8, N10;
- Some feature update for Pinebook Pro;
|
|
The ARM Juno boards (-r1 and -r2) feature a Silicon Image 3132 PCIe
SATA controller soldered on the board, providing two SATA ports.
Enable the driver and the sata command in the defconfig, to be able to
load images from SATA disks.
Tested by loading kernels and Grub/EFI from an SSD and successfully
booting a Linux system (with and without using UEFI).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
