summaryrefslogtreecommitdiff
path: root/cpu
AgeCommit message (Collapse)Author
2008-11-10Merge commit 'wd/master'Jon Loeliger
2008-11-09Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2008-11-09Merge branch 'master' of git://git.denx.de/u-boot-coldfireWolfgang Denk
2008-11-04Change to use "do_div" macroTomohiro Masubuchi
Signed-off-by: Tomohiro Masubuchi <tomohiro_masubuchi@tripeaks.co.jp>
2008-11-04ARM926EJ-S: relocate OMAP specific 'cpuinfo.c' into OMAP directoryRoman Mashak
OMAP identification is implemented in 'cpuinfo.c' and located in ARM926EJ-S directory. It makes sense to place this file in OMAP specific subdirectory, i.e. cpu/arm926ejs/omap Signed-off-by: Roman Mashak <romez777@gmail.com>
2008-11-04powerpc: change 86xx SMP boot methodBecky Bruce
We put the bootpg for the secondary cpus into memory and use BPTR to get to it. This is a step towards converting to the ePAPR boot methodology. Also, the code is written to deal properly with more than 4GB of RAM. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-03powerpc 86xx: Handle CCSR relocation earlierBecky Bruce
Currently, the CCSR gets relocated while translation is enabled, meaning we need 2 BAT translations to get to both the old location and the new location. Also, the DEFAULT CCSR location has a dependency on the BAT that maps the FLASH region. Moving the relocation removes this unnecessary dependency. This makes it easier and more intutive to modify the board's memory map. Swap BATs 3 and 4 on 8610 so that all 86xx boards use the same BAT for CCSR space. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-03ColdFire: Fix compilation errorTsiChung Liew
The error was caused by the change for strmhz() in cpu.c. A few of them were one extra close parenthesis. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03ColdFire: Add MCF5301x CPU and M53017EVB supportTsiChung Liew
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03ColdFire: Add SBF support for M52277EVBTsiChung Liew
Add serial boot support Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03ColdFire: Relocate FEC's GPIO and mii functions protocolsTsiChung Liew
Place FEC pin assignments in cpu_init.c from platform's mii.c Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03ColdFire: Modules header files cleanupTsiChung Liew
Consolidate ATA, ePORT, QSPI, FlexCan, PWM, RNG, MDHA, SKHA, INTC, and FlexBus structures and definitions in immap_5xxx.h to more unify modules header files. Append DSPI support for m547x_8x. SSI cleanup. Remove USB Host structure from immap_539.h. Apply changes to use FlexBus structures in mcf52x2's cpu_init.c and platform configuration files. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-02Consolidate MAX/MIN definitionsAndy Fleming
There were several, now there is one (two if you count the lower-case versions). Signed-off-by: Andy Fleming <afleming@freescale.com>
2008-11-01Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2008-10-3174xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cacheDave Liu
The patch is following the commit 392438406041415fe64ab8748ec5ab5ad01d1cf7 mpc86xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cache This is needed in unlock_ram_in_cache() because it is called from C and will corrupt the small data area anchor that is kept in R2. lock_ram_in_cache() is modified similarly as good coding practice, but is not called from C. Signed-off-by: Nick Spence <nick.spence@freescale.com> also, the r2 is used as global data pointer. Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-10-30Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2008-10-30mpc83xx pci: Round up memory size in inbound window.Scott Wood
The current calculation will fail to cover all memory if its size is not a power of two. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-30Merge branch 'master' of git://git.denx.de/u-boot-mpc86xxWolfgang Denk
2008-10-3086xx: remove the redundant r2 global data pointer saveDave Liu
The commit 67256678f00c09b0a7f19e862e5c1847553d31bc add the another global data pointer save, but in fact the global data pointer will be initialized in the board_init_r, so remove it such as the 85xx/83xx family. Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Kumar Gala <kumar.gala@freescale.com>
2008-10-3086xx: remove the unused code for 86xx familyDave Liu
I believe these code was copied from 74xx family, but for 86xx, it is unused. Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Kumar Gala <kumar.gala@freescale.com>
2008-10-3086xx: Move the clear_tlbs before MMU turn onDave Liu
We must invalidate TLBs before MMU turn on, but currently the code is not, if there are some stale TLB entry valid in the TLBs, it will cause strange issue. Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Becky Bruce <becky.bruce@freescale.com>
2008-10-29Make Freescale local bus registers available for both 83xx and 85xx.Haiying Wang
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it can be shared by both 83xx and 85xx - Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards files which use lbus83xx_t. - Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that 85xx can share them. Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-28i386: Renamed show_boot_progress in assembler codeGraeme Russ
Renamed show_boot_progress in assembler init phase to show_boot_progress_asm to avoid link conflicts with C version Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2008-10-27Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2008-10-2485xx: Fix the incorrect register used for DDR erratum1Dave Liu
The 8572 DDR erratum1: DDR controller may enter an illegal state when operating in 32-bit bus mode with 4-beat bursts. Description: When operating with a 32-bit bus, it is recommended that DDR_SDRAM_CFG[8_BE] is cleared when DDR2 memories are used. This forces the DDR controller to use 4-beat bursts when communicating to the DRAMs. However, an issue exists that could lead to data corruption when the DDR controller is in 32-bit bus mode while using 4-beat bursts. Projected Impact: If the DDR controller is operating in 32-bit bus mode with 4-beat bursts, then the controller may enter into a bad state. All subsequent reads from memory is corrupted. Four-beat bursts with a 32-bit bus only is used with DDR2 memories. Therefore, this erratum does not affect DDR3 mode. Work Arounds: To work around this issue, software must set DEBUG_1[31] in DDR memory mapped space (CCSRBAR offset + 0x2f00 for DDR_1 and CCSRBAR offset + 0x6f00 for DDR_2). Currenlty, the code is using incorrect register DDR_SDRAM_CFG_2 as condition, but it should be DDR_SDRAM_CFG register. Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-10-2485xx: Add basic e500mc core supportKumar Gala
Introduce CONFIG_E500MC to deal with the minor differences between e500v2 and e500mc. * Certain fields of HID0/1 don't exist anymore on e500mc * Cache line size is 64-bytes on e500mc * reset value of PIR is different Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-2485xx: Use CONFIG_SYS_CACHELINE_SIZE instead of magic numberKumar Gala
Using CONFIG_SYS_CACHELINE_SIZE instead of 31 means we can handle e500mc's 64-byte cacheline properly when it gets added. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-24ppc4xx: Generic architecture for xilinx ppc405(v3)Ricardo Ribalda Delgado
As "ppc44x: Unification of virtex5 pp440 boards" did for the xilinx ppc440 boards, this patch presents a common architecture for all the xilinx ppc405 boards. Any custom xilinx ppc405 board can be added very easily with no code duplicity. This patch also adds a simple generic board, that can be used on almost any design with xilinx ppc405 replacing the file ppc405-generic/xparameters.h This patch is prepared to work with the latest version of EDK (10.1) Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-23Blackfin: fix up UART status bit handlingMike Frysinger
Some Blackfin UARTs are read-to-clear while others are write-to-clear. This can cause problems when we poll the LSR and then later try and handle any errors detected. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: small cpu init optimization while setting interrupt maskMike Frysinger
Use the sti instruction to set the initial interrupt mask rather than banging on the core IMASK MMR to save both space and time. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: set initial stack correctly according to Blackfin ABIMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: make baud calculation more accurateMike Frysinger
We should use the algorithm in the Linux kernel so that the UART divisor calculation is more accurate. It also fixes problems on some picky UARTs that have sampling anomalies. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: decode hwerrcause/excause when crashingMike Frysinger
Having to decode hwerrcause/excause values is a pain, so automate it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: fix register dump messagesMike Frysinger
Make sure we report RETI/IPEND correctly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: don't bother displaying reboot msg when crashingMike Frysinger
The hang function already tells you to reboot, so no point in showing it twice. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: enable support for nested interruptsMike Frysinger
During cpu init, make sure we initialize the CEC properly so that interrupts can fire and be handled while U-Boot is running. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: drop unused cache flush codeMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: unify cache handling codeMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-23Blackfin: only enable hardware error irq by defaultMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-10-21mpc83xx: Removed #ifdef CONFIG_MPC834X dependency on upmconfig functionRichard Retanubun
This is done to allow other 83XX based platforms which also have UPM (e.g. 8360) to configure and use their UPM in u-boot. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21mpc83xx: serdes: add forgotten shifts for rfcksAnton Vorontsov
The rfcks should be shifted by 28 bits left. We didn't notice the bug because we were using only 100MHz clocks (for which rfcks == 0). Though, for SGMII we'll need 125MHz clocks. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2008-10-21ppc4xx: Correctly setup ranges property in ebc nodeStefan Roese
Previously only the NOR flash mapping was written into the ranges property of the ebc node. This patch now writes all enabled chip select areas into the ranges property. Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21ppc4xx: Add routine to retrieve CPU numberAdam Graham
Provide a weak defined routine to retrieve the CPU number for reference boards that have multiple CPU's. Default behavior is the existing single CPU print output. Reference boards with multiple CPU's need to provide a board specific routine. See board/amcc/arches/arches.c for an example. Signed-off-by: Adam Graham <agraham@amcc.com> Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21ppc4xx: Add static support for 44x IBM SDRAM ControllerAdam Graham
This patch add the capability to configure a PPC440 based IBM SDRAM Controller with static, compiled-in, values. PPC440 memory subsystem includes a Memory Queue core. Signed-off-by: Adam Graham <agraham@amcc.com> Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21Cleanup: fix "MHz" spellingWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-21Use strmhz() to format clock frequenciesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-21Merge git://git.denx.de/u-boot into x1Markus Klotzbuecher
Conflicts: drivers/usb/usb_ohci.c
2008-10-18Merge 'next' branchWolfgang Denk
Conflicts: board/freescale/mpc8536ds/mpc8536ds.c include/configs/mgcoge.h Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-1885xx if NUM_CPUS>1, print cpu numberEd Swarthout
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>