| Age | Commit message (Collapse) | Author |
|---|
|
use ALLOC_CACHE_ALIGN_BUFFER_PAD for mbr header allocation
in stack to fix alloc issue in is_gpt_valid()
this patch fix also issue for GPT partition handling
with blocksize != 512 in set_protective_mbr()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The check in part_get_info_extended() for a successful partition
searching misses a condition for extended partition. In case of
(ext_part_sector == 0), we should anyway mark the partition as found,
even if it's an extended partition, i.e. (is_extended(pt->sys_ind) == 0).
Otherwise, the extended partition (type 0x0f) will never be identified,
and the following recursive call to part_get_info_extended() will get a
wrong 'part_num' and 'which_part' parameter. In the end, all those
partitions in extended table will not be identified.
Let's add the missing OR condition of (ext_part_sector == 0) for
is_extended() check to fix the problem.
The issue is discovered by running fastboot flash to an extended
partition on eMMC.
$ fastboot flash mmcsda5 cache.img
target reported max download size of 536870912 bytes
sending 'mmcsda5' (18796 KB)...
OKAY [ 2.144s]
writing 'mmcsda5'...
FAILED (remote: cannot find partition)
finished. total time: 2.261s
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Before this patch one could receive following errors when executing
"gpt write" command on machine with cache enabled:
display5 factory > gpt write mmc ${mmcdev} ${partitions}
Writing GPT:
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
success!
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
the partition starting at 0x4400 is refused with overlap error:
$> gpt write mmc 0 "name=test,start=0x4400,size=0"
Writing GPT: Partition overlap
error!
even if the 0x4400 is the first available offset for LBA35 with default
value:
- MBR=LBA1
- GPT header=LBA2
- PTE= 32 LBAs (128 entry), 3 to 34
And the command to have one partition for all the disk failed also :
$> gpt write mmc 0 "name=test,size=0"
After the patch :
$> gpt write mmc 0 "name=test,size=0"
Writing GPT: success!
$> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x01ce9fde "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: b4b84b8a-04e3-4000-0036-aff5c9c495b1
And 0x22 = 34 LBA => offset = 0x4400 is accepted as expected
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The test and info callbacks into the partition callback struct are
used by the "part list" command on the command line. That command
is used by the distro script.
With verb=1 set, "part list" thus throws a lot of warnings about
partitions it can't find when an upper layer searches for partitions.
So let's reduce verbosity to bring it to the same level of noise
as the other partition targets.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
While this goes somewhat against normal coding style we should ensure
that dev_desc is not NULL before we dereference it in allocation of
legacy_mbr.
Reported-by: Coverity (CID: 167292)
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
There is already existing function part_get_info_by_name().
But sometimes user is particularly interested in looking for only
specific partition type. This patch implements such an API that
provides partition searching by name for specified partition type.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Since commit ff98cb90514d ("part: extract MBR signature from partitions")
SPL boot on i.MX6 starts to fail:
U-Boot SPL 2017.09-00221-g0d6ab32 (Oct 02 2017 - 15:13:19)
Trying to boot from MMC1
(keep in loop)
Use the original allocation scheme for the SPL case, so that MX6 boards
can boot again.
This is a temporary solution to avoid the boot regression.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
|
|
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
EFI client programs need the signature information from the partition
table to determine the disk a partition is on, so we need to fill that
in here.
Signed-off-by: Peter Jones <pjones@redhat.com>
[separated from efi_loader part, and fixed build-errors for non-
CONFIG_EFI_PARTITION case]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The UEFI spec allows an EFI system partition (ESP, with the bootloader or
kernel EFI apps on it) to reside on a disk using a "legacy" MBR
partitioning scheme.
But in contrast to actual legacy disks the ESP is not marked as
"bootable" using bit 7 in byte 0 of the legacy partition entry, but is
instead using partition *type* 0xef (in contrast to 0x0b or 0x0c for a
normal FAT partition). The EFI spec isn't 100% clear on this, but it even
seems to discourage the use of the bootable flag for ESPs.
Also it seems that some EFI implementations (EDK2?) even seem to ignore
partitions marked as bootable (probably since they believe they contain
legacy boot code).
The Debian installer [1] (*not* mini.iso), for instance, contains such an
MBR, where none of the two partitions are marked bootable, but the ESP
has clearly type 0xef.
Now U-Boot cannot find the ESP on such a disk (USB flash drive) and
fails to load the EFI grub and thus the installer.
Since it all boils down to the distro bootcmds eventually calling
"part list -bootable" to find potential boot partitions, it seems logical
to just add this "partition type is 0xef" condition to the is_bootable()
implementation.
This allows the bog standard arm64 Debian-testing installer to boot from
an USB pen drive on Allwinner A64 boards (Pine64, BananaPi-M64).
(Ubuntu and other distribution installers don't have a legacy MBR, so
U-Boot falls back to El Torito there).
[1] https://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/arm64/iso-cd/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Needed to support efi file protocol. The fallback.efi loader wants
to be able to read the contents of the /EFI directory to find an OS
to boot.
Modelled after POSIX opendir()/readdir()/closedir(). Unlike the other
fs APIs, this is stateful (ie. state is held in the FS_DIR "directory
stream"), to avoid re-traversing of the directory structure at each
step. The directory stream must be released with closedir() when it
is no longer needed.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Change to use 'debug' to output the error message if it fails to
read the driver descriptor block.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
%s/Desriptor/Descriptor/g
Fix lines over 80 characters with said typo.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The current code checks that no partitions overlap with the GPT partition
table using the offset of the first LBA usable for that partition.
This works fine, unless you have a partition entry that is further away
than it usually is and you want to create partitions in the gap between the
GPT header and the GPT partition entries, for example to reflash a
bootloader that needs to be set there.
Rework the test to something a bit smarter that checks whether a partition
would overlap with either the GPT header or the partition entries, no
matter where it is on the disk.
Partitions that do not have a start LBA specified will still start at the
first LBA usable set in the GPT header, to avoid weird behaviours.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The gpt_fill_pte will need to access the device block size. Let's pass the
device descriptor as an argument.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The start variable is only used inside a loop, and is never affected inside
it, so it's a purely local variable.
In the same way the partition size is accessed several times, so we can
store it in a variable.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Both the config option and the DT options specify the offset to set the GPT
at in bytes, yet the code treats those values as block numbers.
Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
When using ISO partitions with a DMA enabled block device driver
reading the ISO partition leads to unaligned DMA operations:
CACHE: Misaligned operation at range [bffb7da8, bffb85a8]
Align the buffer to make sure we pass a buffer which works for
DMA operations.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This adds a new uclass id and block interface type for NVMe.
Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
In order to read the GPT, modify the partition name strings, and then
write out a new GPT, the disk GUID is needed. While there is an
existing accessor for the partition UUIDs, there is none yet for the
disk GUID.
Changes since v6: none.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
|
|
Move MAX_SEARCH_PARTITIONS to part.h so that functions in cmd
directory can find it. At the same time, increase the value to
64 since some operating systems use many, and the resources
consumed by a larger value are minimal.
Changes since v6: none.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
|
|
Changes since v6: none.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
|
|
Similar to what blk_get_device_part_str() does, this patch makes
part_get_info_by_name() return the partition number in case of a match.
This is useful when the partition number is needed and not just the
descriptor.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The SPARC architecture is currently unmaintained, remove.
Cc: Francois Retief <fgretief@spaceteq.co.za>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Some architectures require their SPL loader at a fixed address within
the first 16KB of the disk. To avoid an overlap with the partition
entries of the EFI partition table, the first safe offset (in bytes,
from the start of the device) for the entries can be set through
CONFIG_EFI_PARTITION_ENTRIES_OFF (via Kconfig)
When formatting a device with an EFI partition table, we may need to
leave a gap between the GPT header (always in LBA 1) and the partition
entries. The GPT header already contains a field to specify the
on-disk location, which has so far always been set to LBA 2. With this
change, a configurable offset will be translated into a LBA address
indicating where to put the entries.
Now also allows an override via device-tree using a config-node (see
doc/device-tree-bindings/config.txt for documentation).
Tested (exporting an internal MMC formatted with this) against Linux,
MacOS X and Windows.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: __maybe_unused on config_offset to avoid warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Change GPT UUID string format from UUID to GUID per specification.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
the socfpga bootrom supports mmc booting from either a raw image
starting at 0x0, or from a partition of type 0xa2. This patch
adds support for locating the boot image in the first type 0xa2
partition found.
Assigned a partition number of -1 will cause a search for a
partition of type CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
and use it to find the u-boot image
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
|
|
On some cases the first 440 bytes of MBR are used to keep an additional
information for ROM boot loader. 'gpt write' command doesn't preserve
that area and makes boot code gone.
Preserve boot code area when run 'gpt write' command.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Brennan Ashton <brn@deako.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
With capacities getting bigger, we can see see messages with negative
numbers like "Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)".
Here the printed LBA is -387938128 when it should have been 3907029168.
To fix this, use the right format when displaying the unsigned integers.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
|
|
In both DOS and ISO partition tables the same code to create partition name
like "hda1" was repeated.
Code moved to into a new function part_set_generic_name() in part.c and optimized.
Added recognition of MMC and SD types, name is like "mmcsda1".
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add special target "mbr" (otherwise configurable via CONFIG_FASTBOOT_MBR_NAME)
to write MBR partition table.
Partitions are now searched using the generic function which finds any
partiiton by name. For MBR the partition names hda1, sda1, etc. are used.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
So far partition search by name has been supported only on the EFI partition
table. This patch extends the search to all partition tables.
Rename part_get_info_efi_by_name() to part_get_info_by_name(), move it from
part_efi.c into part.c and make it a generic function which traverses all part
drivers and searches all partitions (in the order given by the linked list).
For this a new variable struct part_driver.max_entries is added, which limits
the number of partitions searched. For EFI this was GPT_ENTRY_NUMBERS.
Similarly the limit is defined for DOS, ISO, MAC and AMIGA partition tables.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
|
|
The calculation of "dev_desc->lba - 34 - 1 - offset" is not correct for
size '-', because both fist_usable_lba and last_usable_lba will remain
34 sectors.
We can simply use 0 for size '-' because the part_efi module will decode
the size and auto extend the size to maximum available size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This fixes a mismatch between the %zu format and the type used on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Partitions on the iso el torito partition table interpreter
only start from partition 1. So when printing out the tables,
let's also start counting at 1.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
the last value acceptable value for offset is last_usable_lba + 1
and not last_usable_lba - 1
issue found with SDCARD partition commands on u-boot 2015.10
but this part of code don't change
1- create GPT partion on all the card
> gpt write mmc 0 name=test,start=0,size=0
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fde "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: b710eb04-45b9-e94a-8d0b-21458d596f54
=> Start = 0x22*512 = 0x4400
=> Size = (0x003a9fde-0x22+1) * 512 = 0x753F7A00
2- try to recreate the same partition with the next command
(block size:512 bytes = 0x200)
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7A00
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7800
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7600
Writing GPT: success!
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fdc "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: 36ec30ef-7ca4-cd48-97cd-ea9fb95185d0
the max LBA when the size is indicated (0x003a9fdc) is lower than
when u-boot compute the max allowed value with size=0 (0x003a9fde)
in the code :
/* partition ending lba */
if ((i == parts - 1) && (partitions[i].size == 0))
/* extend the last partition to maximuim */
gpt_e[i].ending_lba = gpt_h->last_usable_lba;
else
gpt_e[i].ending_lba = cpu_to_le64(offset - 1);
so offset = gpt_h->last_usable_lba + 1 is acceptable !
but the test (offset >= last_usable_lba) cause the error
END
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>disk: part_efi: fix check of the max partition size
the last value acceptable value for offset is (last_usable_lba + 1)
and not (last_usable_lba - 1)
issue found with SDCARD partition commands on u-boot 2015.10
but this part of code don't change
1- I create GPT partion on all the card (start and size undefined)
> gpt write mmc 0 name=test,start=0,size=0
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fde "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: b710eb04-45b9-e94a-8d0b-21458d596f54
=> Start = 0x22*512 = 0x4400
=> Size = (0x003a9fde-0x22+1) * 512 = 0x753F7A00
2- I try to recreate the same partition with the command gpt write
and with start and size values (block size:512 bytes = 0x200)
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7A00
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7800
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7600
Writing GPT: success!
I check the partition created :
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fdc "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: 36ec30ef-7ca4-cd48-97cd-ea9fb95185d0
=> but the max LBA when the size is indicated (0x003a9fdc) is lower than
when u-boot compute the max allowed value with size=0 (0x003a9fde)
3- in the code, just after my patch, line 446
/* partition ending lba */
if ((i == parts - 1) && (partitions[i].size == 0))
/* extend the last partition to maximuim */
gpt_e[i].ending_lba = gpt_h->last_usable_lba;
else
gpt_e[i].ending_lba = cpu_to_le64(offset - 1);
so offset = gpt_h->last_usable_lba + 1 is acceptable !
(it the value used when size is 0)
but today the test (offset >= last_usable_lba) cause the error
my patch only solve this issue
END
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Return -EINVAL instead of -1 in this function, to provide a more meaningful
error.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This is not needed since we can use the functions provided by the legacy
block device support.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Drop use of the table in part.c for this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function is implemented by the legacy block functions now. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
