| Age | Commit message (Collapse) | Author |
|---|
|
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Gray Remlin <gryrmln@gmail.com>
|
|
Consider that ide_preinit() succeed if at least one port is successfully
initialized. This allows to iniatialize IDE support on a board with two
SATA ports but a single hard disk available.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
|
|
Before the actual initialization do a hard reset of the SATA port and the
connected device.
changes v1->v2:
- add comment for udelay
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
|
|
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
mvsata_ide_initialize_port(): adjust init sequence (SStatus
should be checked only after all writes to SControl) and
return success/failure to ide_preinit().
Also, as some tests showed init durations in the hundreds
of us, raise the time-out to 01 ms to be on the safe side.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
|
|
This driver only provides initialization code; actual driving
is done by cmd_ide.c using the ATA compatibility mode of the
Marvell SATAHC controller.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
|
