summaryrefslogtreecommitdiff
path: root/drivers/block/mvsata_ide.c
AgeCommit message (Collapse)Author
2016-01-14arm: mvebu: Move SoC selection (A38X vs AXP) into KconfigStefan Roese
Until now, the SoC selection for the ARCH_MVEBU platforms has been done in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As it needed to get selected for AXP and A38x based boards. This patch now changes this to move the SoC selection to Kconfig. And also uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x. This makes things a bit clearer - especially for new board additions. Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available CONFIG_ARMADA_38X and CONFIG_ARMADA_XP. And CONFIG_DDR3 is removed, as its not referenced anywhere. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-23arm: mvebu: add Armada XP SATA supportAnton Schubert
This patch initializes the SATA address windows on Armada XP and allows it to work with the existing mvsata_ide driver. It also adds the necessary configuration for the db-mv784mp-gp board. Signed-off-by: Anton Schubert <anton.schubert@gmx.de> Tested-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2014-10-23arm: marvell: Move arch/kirkwood.h to arch/soc.hStefan Roese
This move makes is possible to use this header not only from kirkwood platforms but from all Marvell mvebu platforms. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Luka Perkov <luka@openwrt.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2013-07-24Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11mvsata_ide.c: Correction of typo in commentsGray Remlin
Signed-off-by: Gray Remlin <gryrmln@gmail.com>
2011-12-06mvsata: fix ide_preinit for missing disksSimon Guinot
Consider that ide_preinit() succeed if at least one port is successfully initialized. This allows to iniatialize IDE support on a board with two SATA ports but a single hard disk available. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2011-05-23mvsata: issue hard reset on initializationMichael Walle
Before the actual initialization do a hard reset of the SATA port and the connected device. changes v1->v2: - add comment for udelay Signed-off-by: Michael Walle <michael@walle.cc> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-04-27Replace obsolete e-mail addressAlbert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2010-10-13mvsata_ide: adjust port init sequenceAlbert Aribaud
mvsata_ide_initialize_port(): adjust init sequence (SStatus should be checked only after all writes to SControl) and return success/failure to ide_preinit(). Also, as some tests showed init durations in the hundreds of us, raise the time-out to 01 ms to be on the safe side. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-08-08ide: add mvsata_ide driverAlbert Aribaud
This driver only provides initialization code; actual driving is done by cmd_ide.c using the ATA compatibility mode of the Marvell SATAHC controller. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>