summaryrefslogtreecommitdiff
path: root/drivers/block
AgeCommit message (Collapse)Author
2012-11-02ahci: Support splitting of read transactions into multiple chunksVadim Bendebury
With an Intel AHCI controller, the driver does not operate properly if the requested amount of blocks to read exceeds 255. It is probably possible to specify 0 as the block count and the driver will read 256 blocks, but it was decided to limit the number of blocks read at once to 128 (it should be a power of 2 for the optimal performance of solid state drives). Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
2012-10-15sata.h: Make all sata/ata drivers include <sata.h>Pavel Herrmann
- block_dev_desc_t says that block_(read|write) take lbaint_t for blkcnt not ulong. - We also move the extern of sata_dev_desc into <sata.h> - Remove now duplicate declarations from driver-specific headers. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
2012-10-15sil_sata: Make sata_write() comply with <part.h>Tom Rini
sata_write() takes a const void as the last argument. Fixing this means we also need to make ata_low_level_rw_lba{28,48} also take a const void. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15sata_dwc: Make sata_write() use const void, per <part.h>Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15pata_bfin: Make sata_{read,write}() comply with <part.h>Tom Rini
These functions take lbaint_t for blkcnt. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15fsl_sata: Make sata_{read,write}() comply with <part.h>Tom Rini
- sata_write() takes a const void as the last argument. Fixing this means we also need to make ata_low_level_rw_lba{28,48} also take a const void. - Both sata_{read,write} take lbaint_t for blkcnt and ulong for blknr Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15dwc_ahsata: Make sata_write() comply with <part.h>Tom Rini
sata_write() takes a const void as the last argument. Fixing this means we also need to make ata_low_level_rw_lba{28,48} also take a const void. Acked-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15ata_piix: sata_write must take a const void argument.Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15ata_piix: Fix checkpatch issuesTom Rini
While in here also: - Switch to debug from custom PRINTF for debugging. - Use mdelay rather than custom msleep. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-28remove unnecessary code in ata_piixPavel Herrmann
We set sata_curr_device to 0 right after returning from init_sata(), so there's no point in setting it to the last scanned driver at this point. Note: there are more duplicities with cmd_sata, but those might be required, as the code seems to reset the entire controller on every scan, ignoring the requested port number. Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
2012-09-11block: systemace: Simplify base and width initializationMichal Simek
Use CONFIG parameters only at one location to simplify the code. Also create ace_readw/writew functions. Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-07-08Remove remaining mdelay() macrosAnatolij Gustschin
Drop mdelay() macros since we already have a common mdelay() func. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-06-21Block: Remove MG DISK supportMarek Vasut
This driver is unused and obsolete. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: unsik Kim <donari75@gmail.com>
2012-05-15SATA: add driver for MX5 / MX6 SOCsStefano Babic
This driver is part of Freescale's LTIB for MX5 / MX6. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Terry Lv <r65388@freescale.com> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-12Blackfin: pata_bfin: fix printf warningMike Frysinger
pata_bfin.c: In function 'bfin_ata_identify': pata_bfin.c:887:2: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'lbaint_t' Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-12-06mvsata: fix ide_preinit for missing disksSimon Guinot
Consider that ide_preinit() succeed if at least one port is successfully initialized. This allows to iniatialize IDE support on a board with two SATA ports but a single hard disk available. Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2011-12-02drivers/block/sata_dwc.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: sata_dwc.c: In function 'scan_sata': sata_dwc.c:535:38: warning: variable 'udma_mask' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Kazuaki Ichinohe <kazuichi@fsi.co.jp>
2011-11-29powerpc/85xx: always implement the work-around for Erratum SATA_A001Timur Tabi
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented only if U-Boot initializes SATA, but SATA is not initialized by default. So move the work-around to the CPU initialization function, so that it's always executed on the SOCs that need it. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-18ftide020: fix incorrect information display formatMacpaul Lin
Fix incorrect information display format when probing the device. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-11-16sata_dwc.c: Fix GCC 4.6 build warningsStefan Roese
Fix: sata_dwc.c: In function 'sata_dwc_softreset': sata_dwc.c:444:5: warning: variable 'status' set but not used [-Wunused-but-set-variable] sata_dwc.c:443:6: warning: variable 'serror' set but not used [-Wunused-but-set-variable] sata_dwc.c: In function 'scan_sata': sata_dwc.c:654:16: warning: variable 'lba_desc' set but not used [-Wunused-but-set-variable] sata_dwc.c:538:16: warning: variable 'xfer_mask' set but not used [-Wunused-but-set-variable] sata_dwc.c: In function 'ata_dev_read_id': sata_dwc.c:747:14: warning: variable 'reason' set but not used [-Wunused-but-set-variable] sata_dwc.c: In function 'ata_dev_read_sectors': sata_dwc.c:1810:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable] sata_dwc.c: In function 'ata_dev_write_sectors': sata_dwc.c:1994:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable] Signed-off-by: Stefan Roese <sr@denx.de>
2011-11-16drivers/block/sym53c8xx.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: sym53c8xx.c: In function 'scsi_write_dsp': sym53c8xx.c:456:16: warning: variable 'val' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-16drivers/block/sata_sil3114.c: Fix GCC 4.6 build warningKumar Gala
Fix: sata_sil3114.c: In function 'scan_sata': sata_sil3114.c:793:7: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:794:7: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:795:39: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:795:7: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:797:7: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:800:7: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:801:7: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:802:39: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:802:7: warning: array subscript is above array bounds [-Warray-bounds] sata_sil3114.c:804:7: warning: array subscript is above array bounds [-Warray-bounds] Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-16drivers/block/ahci.c: Fix GCC 4.6 build warningKumar Gala
Fix: ahci.c: In function 'ata_scsiop_read10': ahci.c:564:6: warning: variable 'lba' set but not used [-Wunused-but-set-variable] Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-27GCC4.6: Squash warnings in sata_sil3114.cMarek Vasut
sata_sil3114.c: In function 'sata_identify': sata_sil3114.c:174: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'lbaint_t' Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
2011-10-27GCC4.6: Squash warnings in ahci.cMarek Vasut
ahci.c: In function 'ahci_port_start': ahci.c:401: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'struct ahci_cmd_hdr *' Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
2011-10-22consolidate mdelay by providing a common function for all usersAnatolij Gustschin
There are several mdelay() definitions in the driver and board code. Remove them all and provide a common mdelay() in lib/time.c. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22drivers: add the support for Silicon Image SATA controllerTang Yuantian
Add the Silicon Image series PCI Express to Serial ATA controller support, including Sil3132, Sil3131 and Sil3124. The SATA controller can be used to load kernel. The features list: - Supports 1-lane 2.5 Gbit/s PCI Express - Supports one/two/four independent Serial ATA channels - Supports Serial ATA Generation 2 transfer rate of 3.0 Gbit/s - Supports LBA28 and LBA48 Signed-off-by: Tang Yuantian <b29983@freescale.com> Signed-off-by: Aaron Williams <Aaron.Williams@cavium.com> Tested-by: Lan Chunhe <b25806@freescale.com>
2011-10-09fsl_sata: Fix compile error when CONFIG_LBA48 is not definedTang Yuantian
If CONFIG_LBA48 is not defined, the element lba48 of struct sata_dev_desc is not avaible, and can't be used. Signed-off-by: Tang Yuantian <b29983@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-30ATA: Squash warnings in mxc_ata.Marek Vasut
mxc_ata.c: In function ‘set_ata_bus_timing’: mxc_ata.c:118: warning: dereferencing type-punned pointer will break strict-aliasing rules mxc_ata.c:125: warning: dereferencing type-punned pointer will break strict-aliasing rules mxc_ata.c:129: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
2011-08-04Convert ISO-8859 files to UTF-8Albert ARIBAUD
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source tree, which could cause issues with the patchwork review system. This commit converts all ISO-8859 files to UTF-8. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-07-26Timer: Allow reset_timer() only for systems with low resolution timersGraeme Russ
2011-07-26disk/part.c: Make features optionalMatthew McClintock
If we don't want to build support for any partition types we can now add #undef CONFIG_PARTITIONS in a board config file to keep this from being compiled in. Otherwise boards assume this is compiled in by default Signed-off-by: Matthew McClintock <msm@freescale.com>
2011-07-26scsi/ahci: add support for non-PCI controllersRob Herring
Add support for AHCI controllers that are not PCI based. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Wolfgang Denk <wd@denx.de>
2011-07-26scsi/ahci: ata id little endian fixRob Herring
The ata id string always needs swapping, not just on BE machines. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2011-05-23mvsata: issue hard reset on initializationMichael Walle
Before the actual initialization do a hard reset of the SATA port and the connected device. changes v1->v2: - add comment for udelay Signed-off-by: Michael Walle <michael@walle.cc> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-05-12ftide020: add faraday ide ahb controllerMacpaul Lin
Faraday's ftide020_s is an IDE-AHB controller for SoC design. This patch add the u-boot driver (PIO) of ftide020 ATA (IDE) driver. IDE commands include read, info, and other functions has been implemented. Because this IDE controller support AHB interface only which is differ from other most IDE controller supports PCI interface. Some registers access is required during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" is required to be defined according to the feature in cmd_ide.c. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-04-27Replace obsolete e-mail addressAlbert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-02-02MXC: removed warnings from IMX51 ATA driverStefano Babic
Drop warnings due to unused variables. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Marek Vasut <marek.vasut@gmail.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-02-02BLOCK: Add freescale IMX51 PATA driverMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
2010-11-17Switch from archive libraries to partial linkingSebastien Carlier
Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-10-13mvsata_ide: adjust port init sequenceAlbert Aribaud
mvsata_ide_initialize_port(): adjust init sequence (SStatus should be checked only after all writes to SControl) and return success/failure to ide_preinit(). Also, as some tests showed init durations in the hundreds of us, raise the time-out to 01 ms to be on the safe side. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-08-08ide: add mvsata_ide driverAlbert Aribaud
This driver only provides initialization code; actual driving is done by cmd_ide.c using the ATA compatibility mode of the Marvell SATAHC controller. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-08-08ide: reorder object files alphabeticallyAlbert Aribaud
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-07-13Blackfin: pata_bfin: convert to portmux frameworkMike Frysinger
Rather than bang MMRs directly, use the new portmux framework to handle the details. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-1285xx/fsl-sata: Use is_serdes_configured() to determine if SATA is enabledKumar Gala
On the MPC85xx platform if we have SATA its connected on SERDES. Determing if SATA is enabled via sata_initialize should not be board specific and thus we move it out of the MPC8536DS board code. Additionally, now that we have is_serdes_configured() we can determine if the given SATA port is enabled and error out if its not in the driver. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26fsl_sata: Move the snoop bit to another placeDave Liu
For P1022 SATA host controller, the data snoop bit of DW3 in PRDT is moved to bit28. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26fsl_sata: Add the workaround for errata SATA-A001Dave Liu
After power on, the SATA host controller of P1022 Rev1 is configured in legacy mode instead of the expected enterprise mode. Software needs to clear bit[28] of HControl register to change to enterprise mode after bringing the host offline. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-09-04Misc SATA fixupsGraeme Russ
Cast first parameter to sata_cpy() In /drivers/block/ata_piix.h, ata_id_has_lba48(), ata_id_has_lba(), ata_id_has_dma(), ata_id_u32(), ata_id_u64() are all defined in include/libata.h which is included in ata.h which is included by all files which include ata_piix.h (only ata_piix.c) so these definitions are supurflous to (and conlict with) this in libata.h. Interestingly, my compiler complains about ata_id_u64 already being defined, but not ata_id_u32 ata_dump_id() is defined in include/libata.h and should not be static (maybe should even use ata_dump_id() in libata.c Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2009-07-29Update Freescale copyrights to remove "All Rights Reserved"Kumar Gala
"All Rights Reserved" conflicts with the GPL. Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
2009-07-23ahci: Fix gcc 4.4 compiler warningKumar Gala
ahci.c: In function 'ata_scsiop_read_capacity10': ahci.c:616: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2024-12-26 13:32:05 +0000