| Age | Commit message (Collapse) | Author |
|---|
|
Synopsys HSDK clock controller generates and supplies clocks to various
controllers and peripherals within the SoC.
Each clock has assigned identifier and client device tree nodes can use
this identifier to specify the clock which they consume. All available
clocks are defined as preprocessor macros in the
dt-bindings/clock/snps,hsdk-cgu.h header and can be used in device
tree sources.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Add rk3128 clock driver and cru structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
Differentiate the generic clock source selection value from the parent
clock index to fix the incorrect assignment of the generic clock
source selection.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
To get the same behavior as the Linux driver, instead of selecting
the closest inferior rate, select the closest inferior or superior
rate
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
What the AT91_UTMI depends on SPL_DM isn't right. AT91_UTMI is not
only used in SPL, also in other place, even if SPL_DM isn't enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Like STM32H7, now STM32F4/F7 clock drivers are binded by
MFD stm32_rcc driver.
This also allows to add reset support to STM32F4/F7 SoCs family.
As Reset driver is not part of SPL supported drivers, don't bind it
in case of SPL to avoid that stm32_rcc_bind() returns an error.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Now that clk_stm32f7.c manages clocks for both STM32F4 and F7 SoCs
rename it to a more generic clk_stm32f.c
Fix also some checkpatch errors/warnings.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
STM32F4 and STM32F7 RCC clock IP are very similar.
Same driver can be used to managed RCC clock for
these 2 SoCs.
Differences between STM32F4 and F7 will be managed using
different compatible string :
_ overdrive clock is only supported by STM32F7
_ different sys_pll_psc parameters can be used between STM32F4
and STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Add a dedicated stm32f7 compatible string to use clk_stm32f7
driver with both STM32F4 and STM32F7 SoCs.
It will be needed to manage differences between these 2 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Add xHCI entry into the clock tables, so that the xHCI USB driver
can enable the clock for the xHCI block via clock framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The MSTP registers were poked in boards/renesas/rcar-common/common.c
in arch_preboot_os hook thus far to shut down the clock before Linux
takes over. With DM, this is no longer needed and we can do the same
in the clock driver .remove callback. This patch adds such a .remove
callback for R8A7795 and R8A7796.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The RK3399 clk driver still has a left-over use of extract_bits, which
can be replaced by using bitfield_extract from include/bitfield.h.
This rewrites the invocation to use the shared function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Using priv for new sysreset driver binding.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Fix clock division factor initialization for RCC_PLLCFGR
registers.
PLLR bits (bit 31-28) in RCC_PLLCFGR must not be cleared,
it's a forbidden value. So update RCC_PLLCFGR using
clrsetbits_le32() to set only necessary bits fields.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Uniformize STMicroelectronics copyrights headers for STM32
related code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Init the CPU and its buses to speed up the boot time.
Move rkclk_init() to a place after rk3399_configure_cpu has defined
at the same time, or else there will be a warning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Fix bit 2 name of PWR_CR3 register to match with the
last STM32H7 reference manual available here :
http://www.st.com/content/st_com/en/support/resources/
resource-selector.html?querycriteria=productId=SS1951$$
resourceCategory=technical_literature$$resourceType=reference_manual
Update also comment about voltage scaling 1 values
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
CLK() macro is a residue of a previously reworked patch,
remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
This allows the NAND driver to enable clock and get its clock rate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add basic clock data for Socionext's new SoC PXs3.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
U-Boot does not support fancy clock tree structures like the Linux
common clock framework. Implement a simple clock tree model at the
driver level. With this, the clock data will be simplified.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The pd_bus hclk/pclk source is pd_bus aclk, not the PLL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Fix typo RK322X/RK3036 in rk322x clock driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Add missing .priv_auto_alloc_size() callback.
Previously private struct stm32_clk was not allocate
which leads to unpredictable behaviour
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add missing RPC hyperflash entry into the clock driver tables.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The SDxCKCR must be configured correctly, otherwise the SDIF can be
unstable. This is done in board files thus far, but those are going
away, so move the setting of SDxCKCR into the correct place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This driver implements basic clock setup, only clock gating
is implemented.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
Files include/dt-bindings/clock/stm32h7-clks.h and
doc/device-tree-bindings/clock/st,stm32h7-rcc.txt
will be available soon in a kernel tag, as all the
bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the clock driver for the RK3399 to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The generic ehci-driver (ehci-generic.c) will try to enable the clocks
listed in the DTSI. If this fails (e.g. due to clk_enable not being
implemented in a driver and -ENOSYS being returned by the clk-uclass),
the driver will bail our and print an error message.
This implements a minimal clk_enable for the RK3399 and supports the
clocks mandatory for the EHCI controllers; as these are enabled by
default we simply return success.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the clock driver for the RK3368 to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in clk_rk3368.c
|
|
We want to support more than one phandle argument. It makes sense to use
an array for this rather than discrete struct members. Adjust the code to
support this. Rename the member to 'arg' instead of 'id'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Rather than naming the phandle struct according to the number of cells it
uses (e.g. struct phandle_2_cell) name it according to the number of
arguments it has (e.g. struct phandle_1_arg). This is a more intuitive
naming.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
|
|
When using 32-bit addresses dtoc works correctly. For 64-bit addresses it
does not since it ignores the #address-cells and #size-cells properties.
Update the tool to use fdt64_t as the element type for reg properties when
either the address or size is larger than one cell. Use the correct value
so that C code can obtain the information from the device tree easily.
Alos create a new type, fdt_val_t, which is defined to either fdt32_t or
fdt64_t depending on the word size of the machine. This type corresponds
to fdt_addr_t and fdt_size_t. Unfortunately we cannot just use those types
since they are defined to phys_addr_t and phys_size_t which use
'unsigned long' in the 32-bit case, rather than 'unsigned int'.
Add tests for the four combinations of address and size values (32/32,
64/64, 32/64, 64/32). Also update existing uses for rk3399 and rk3368
which now need to use the new fdt_val_t type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
|
|
By default, it is assumed that the UTMI clock is generated from
a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ
field of the SFR_UTMICKTRIM has to be updated to generate the UTMI
clock in the proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target
of 480 MHz.
The patch is cloned from the patch of mailing-list:
[PATCH v2] clk: at91: utmi: set the mainck rate
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
[trini: Depend on SPL_DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The SPL_CLK config should depend on SPL && SPL_DM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Support system clocks for LD4, Pro4, sLD8, Pro5, PXs2/LD6b, LD11, LD20.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The R8A7795 and R8A7796 tables use different constants to identify
clock in DT, so split the tables and use the correct constants on
R8A7795. This fixes UART clock misconfiguration on R8A7795.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This SoC is too old. It is difficult to maintain any longer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Since commit f0776a551764 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:
$ make uniphier_v8_defconfig
warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)
While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
