| Age | Commit message (Collapse) | Author |
|---|
|
Convert Stratix 10 SDRAM driver to device model.
Get rid of call to socfpga_per_reset() and use reset
framework.
SPL is changed from calling function in SDRAM driver
directly to just probing UCLASS_RAM.
Move sdram_s10.h from arch to driver/ddr/altera directory.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Compile ALTERA_SDRAM driver in SPL only.
Rename ALTERA_SDRAM to SPL_ALTERA_SDRAM.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Scrub memory content if ECC is enabled and it is not
from warm reset boot.
Enable icache and dcache before scrub memory
and use "DC ZVA" instruction to clear memory
to zeros. This instruction writes a cache line
at a time and it can prevent false ECC error
trigger if write cache line partially.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Stratix 10 maps dram from 0 to 128GB. There is a 2GB hole
in the memory for peripherals and other IO from 2GB to 4GB.
However the dram controller ignores upper address bits for
smaller dram configurations. Example: a 4GB dram
maps to multiple locations, every 4GB on the address.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Move SDRAM size check to SDRAM driver. sdram_calculate_size()
is called in SDRAM initialization already, avoid calling
twice in size check function.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
To clean up reset handling for socfpga gen5, port the DDR driver to DM
using UCLASS_RAM and implement proper reset handling.
This gets us rid of one ad-hoc call to socfpga_per_reset().
The gen5 driver is implemented in 2 distinct files. One of it (containing
the calibration training) is not touched much and is kept at using
hard coded addresses since the code grows even more otherwise.
SPL is changed from calling hard into the DDR driver code to just
probing UCLASS_RESET and UCLASS_RAM. It is happy after finding a RAM
driver after that.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Replace the current rather convoluted code using ad-hoc polling
mechanism with a more straightforward code. Use wait_for_bit_le32()
to poll the DDRCALSTAT register instead of local reimplementation.
It makes no sense to pull for 5 seconds before giving up and trying
to restart the EMIF, so instead wait 500 mSec for the calibration to
complete and if this fails, restart the EMIF and try again. Perform
this 32 times instead of 3 times as the original code did.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
The EMIF reset code can well use wait_for_bit_le32() instead of all that
convoluted polling code. Reduce the timeout from 100 seconds to 1 second,
since if the EMIF fails to reset itself in 1 second, it's unlikely longer
wait would help. Make sure to clear the EMIF reset request even if the
SEQ2CORE_INT_RESP_BIT isn't asserted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
The current EMIF clear timeout handling code was applying bitwise
operations to signed data types and as it was, was extremely hard
to read. Replace it with simple wait_for_bit(). Expand the error
handling to make it more readable too.
This patch also changes the timeout for emif_clear() from 14 hours
to 1 second.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
The debug print is missing a newline, add it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
The Altera Arria10 DDR driver was using constants in a few places
instead of reading registers associated with those constants, fix
this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Incorrect type of size variable results in 0 being
returned for sdram sizes greater than or equal to
4GB.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
|
|
The SDRAM must first be rewritten by zeroes if ECC is used to initialize
the ECC metadata. Make the CPU overwrite the DRAM with zeroes in such a
case. This scrubbing implementation turns the caches on temporarily, then
overwrites the whole RAM with zeroes, flushes the caches and turns them
off again. This provides satisfactory performance.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
This function was never used in SPL and the default implementation of
dram_bank_mmu_setup() does the same thing. The only difference is the
part which configures OCRAM as cachable, which doesn't really work as
it covers more than the OCRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add DDR support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch enables DDR Kconfig support for Arria 10.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add DDR driver support for Arria 10.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Current sdram driver is only applied to gen5 device, hence it is better
to rename sdram driver to more specific name which is related to gen5
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This driver has been using printf() including filename since it was
added. Convert to using debug() instead.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
|
|
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
To enable configuration of sdr.ctrlcfg.extratime1 register which enable
extra clocks for read to write command timing. This is critical to
ensure successful LPDDR2 interface
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
The code uses a lot of signed numbers, which ended up in variables
of unsigned type, which resulted in all sorts of underflows. This
in turn caused incorrect calibration on certain boards. Moreover,
repair the readout of the DQ delay, which was being pulled from
wrong register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Just staticize global variables in sequencer, since there is no
point in having these symbols available outside of the DDR code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Originally, the DLEVEL selects the debug level within the sequencer code,
but only displays the messages on that particular debug level. Tweak the
handling such that for particular debug level, debug messages on that
level and lower are displayed. This allows better regulation of debug
message verbosity.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
This one last set of delay configuration registers was not properly
zeroed out originally, fix it and zero them out.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
There is no point in resetting the ODT setting if the write test
failed, since the code will always retry the calibration and thus
reconfigure the ODT anyway OR the code will fail calibration and
halt.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Every invocation of the scc_mgr_set_dqs_en_delay_all_ranks() is
followed by SCC manager update. Moreover, only this function
triggers the SCC manager update internally. Thus, remove the
internal invocation to avoid triggering the update twice.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
The hi address bitfield in the protection rule must be set to
the last address in the region which the rule represents. The
behavior is now in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
The code should be setting registers to zero, not one register to value.
Swap the order of arguments to correct the behavior. The behavior is now
in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
In the most unlikely case the DQS tracking was to be disabled,
make sure we do not errornously re-enable it. Note that DQS
tracking is enabled on all systems observed thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
The bit 22 is in fact DQS tracking enable bit (dqstrken) and there
is a macro for this bit already, so use it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Init the rule ID, otherwise the debug code will always dump the
protection settings entry 0.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
|
|
Fix the following problem:
drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full':
drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (found_passing_read && found_failing_read)
^
drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here
u32 found_passing_read, found_failing_read, initial_failing_dtap;
^
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
This gem is really really rare, there was an actual float used in
the Altera DDR init code, which pulled in floating point ops from
the libgcc, just wow.
Since we don't support floating point operations the same way Linux
does not support them, replace this with an integer multiplication
and division combo. This removes some 2kiB of size from the SPL as
the floating point ops are no longer pulled in from libgcc.
This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which
does not contain the floating point bits.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Replace uintNN_t with uNN. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
This is defined in the QTS-generated headers, so it must not be
re-defined in sequencer.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
These parameters are not used in the code, zap them and the
macros which are used by them as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
