| Age | Commit message (Collapse) | Author |
|---|
|
This converts the following to Kconfig:
CONFIG_MXS_GPIO
Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/571260789
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
recently added gpio hog patch was "in discussion"
state with Simon Glass. This patch now adds most
of comments from Simon Glass.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Add missing parenthesis to the GPIO_TO_PORT macro.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This patch adds support for DM/DTS in the mxs_gpio.c driver.
Information regarding per gpio controller pin number is passed via DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
- Beelink-x2 STB support (Marcus)
- H6 DDR3, LPDDR3 changes (Andre, Jernej)
- H6 pin controller, USB PHY (Andre)
|
|
The Allwinner H6 pin controller is not really special, at least not when
it comes to normal GPIO operation.
Add the H6 compatible strings to the list of recognised strings, to make
GPIOs work for H6 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
|
|
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
As compatible string "st,stm32-gpio" is no more used, .ofmatch
callback becomes useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
As this driver is used on stm32f4/f7/h7 and stm32mp1
SoCs, rename it with a more generic name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch solves the following warnings:
drivers/gpio/stm32_gpio.c: In function 'stm32_offset_to_index':
: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (idx == offset)
^~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add TI TCA9539 compatible string for yet another I2C GPIO expander.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
commit 1b898ffc040b ("gpio: dwapb_gpio: convert to livetree") introduced
a bug in that dev->node of the gpio chip was accidentally set to the
of_node of its bank subnode.
What it meant to do was assign subdev->node, not dev->node.
While this doesn't affect too many use cases, iterating over the gpio
chip's properties doesn't work any more after that, so fix this.
Fixes: commit 1b898ffc040b ("gpio: dwapb_gpio: convert to livetree")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Convert 'gpio_dwapb_bind' to iterate over subnodes using livetree
functions (inspired from mt7621_gpio.c).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Add GPIO driver for RZ/A1 SoC. The IP is very different from the
R-Car Gen2/Gen3 one already present in the tree, hence a custom
driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
- Various pinctrl / gpio fixes for R-Car
|
|
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
|
|
Switch to generic pin controller API for configuring pins as GPIOs
instead of using the ad-hoc call into the R-Car PFC driver. Moreover,
add .free() implementation for the GPIO controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This IP is also used on some arm SoC, so we allow
to use this driver on arch bcm63158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
This IP is also used on some arm SoC, so we allow
to use this driver on arch bcm6858.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
This driver is used on several big endian mips board.
So we could use raw I/O function instead of forcing
big endian access.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
gpio_get_value should return 0 or 1, not the value of bit & (1 << pin)
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
|
|
Allow rockchip boards to use GPIOs before driver model is ready. This is
really only useful for setting GPIOs to enable the early debug console, if
needed on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Introduce CONFIG_SPL_DM_PCA953X for SPL usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
With the new mscc_bb_spi.c driver, there is no longer use for the
gpio-mscc-bitbang-spi.c driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.
By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.
This adds the base driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
|
|
In order to keep SPL code size below the 32Kb limit,
put under CONFIG_SPL_BUILD flag all unused code in SPL.
This is needed for stm32f7xx board which are using SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In case "gpio-ranges" property is not present in device tree,
use default value for gpio_count and gpio_range.
This fixes an issue on stm32 F7 and H7 boards where "pinmux status -a"
command didn't return any pin status due to the fact that both stm32 F7
and H7 board DT doesn't use the gpio-ranges property.
Fixes: dbf928dd2634a6("gpio: stm32f7: Add gpio bank holes management")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
imx for 2019.01
- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x
|
|
Rename mx8m,MX8M to imx8m,IMX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
|
|
The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI
flash directly in memory. However, for writing in the flash the
communication has to be done by software.
Each of the signal used for the SPI are exposed in a single register. In
order to be able to use the soft-spi driver, the management of this pin
is done through this simple gpio driver.
Even if the main purpose of this driver is to be used by soft-spi, it can
still be used as a normal gpio driver but with limitation: for example
the first pin can't be used as output.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
As all STM32 SoCs supports CONFIG_CLK flag,
it becomes useless in this driver, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
To allow access to this define by other driver, move
it into gpio.h
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As a preparation for merging the socfpga gen5 devicetree files
from Linux, this patch makes the dwapb gpio driver work correctly
without the 'bank-name' property on the gpio-controller nodes.
This property is not present in the Linux drivers and thus is not
present in the Linux devicetrees. It is only used to access pins
via bank name.
This fallback is necessary since without it, the driver will
return an error code which will lead to an error in U-Boot
startup.
The bank names will still be added to the default board device
trees in follow-up patch, but other boards using this driver and
not including the bank name should also work with the socfpga.dtsi
without adding the bank-name property.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on
MT7688 (Gardena smart-gateway). The driver is loosly based on the
Linux kernel version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned']
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This patch adds gpio get_function ops support.
This function reports the state of a gpio.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The pca953x_gpio driver uses default value of polarity inversion
register. For some devices like PCA9557 and MAX7310, their polarity
inversion register default value is 0xf0. So for high 4 ports, when
reading their values, the values are inverted as the actual level.
This patch clears the polarity inversion register to 0 at init, so
that the port read and write values are aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Commit fb01e07a95 accidentally broke initialisation of GPIO
descriptor flags from device tree: currently the active low
flag from gpio-specifier is always ignored. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
|
|
Merged imx8 architecture, fix build for imx8 + warnings
|
|
Add i.MX8 support, there are 8 GPIO banks.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Push generic defines of gpio.h out of mach-davinci to drivers/gpio
now that non-davinci architectures are beginning to use this IP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix calimain build]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add k2g compatible so that k3 SoCs can be supported
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Change to use managed resource function devm_kcalloc(),
so it will auto free memory when driver is removed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
This changes the driver to use dev_read_addr() which is safe both for
flat trees and live trees.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add code to reset all reset signals as in gpio DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
