summaryrefslogtreecommitdiff
path: root/drivers/gpio
AgeCommit message (Collapse)Author
2019-01-16mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.cLars Povlsen
With the new mscc_bb_spi.c driver, there is no longer use for the gpio-mscc-bitbang-spi.c driver. Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-16mips: mscc_sgpio: Add the MSCC serial GPIO device (SIO)Lars Povlsen
This add support for the the MSCC serial GPIO driver in MSCC VCoreIII-based SOCs. By using a serial interface, the SIO controller significantly extends the number of available GPIOs with a minimum number of additional pins on the device. The primary purpose of the SIO controller is to connect control signals from SFP modules and to act as an LED controller. This adds the base driver. Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
2019-01-09gpio: stm32f7: Fix SPL code sizePatrice Chotard
In order to keep SPL code size below the 32Kb limit, put under CONFIG_SPL_BUILD flag all unused code in SPL. This is needed for stm32f7xx board which are using SPL. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-01-09gpio: stm32f7: Fix gpio bank hole managementPatrice Chotard
In case "gpio-ranges" property is not present in device tree, use default value for gpio_count and gpio_range. This fixes an issue on stm32 F7 and H7 boards where "pinmux status -a" command didn't return any pin status due to the fact that both stm32 F7 and H7 board DT doesn't use the gpio-ranges property. Fixes: dbf928dd2634a6("gpio: stm32f7: Add gpio bank holes management") Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-01-01Merge tag 'u-boot-imx-20190101' of git://www.denx.de/git/u-boot-imxTom Rini
imx for 2019.01 - introduce support for i.MX8M - fix size limit for Vhybrid / pico boards - several board fixes - w1 driver for MX2x / MX5x
2019-01-01imx: rename mx8m,MX8M to imx8m,IMX8MPeng Fan
Rename mx8m,MX8M to imx8m,IMX8M Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jon Nettleton <jon@solid-run.com>
2018-12-19gpio: mscc-bitbang-spi: Add a simple gpio driver for bitbgang spiGregory CLEMENT
The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI flash directly in memory. However, for writing in the flash the communication has to be done by software. Each of the signal used for the SPI are exposed in a single register. In order to be able to use the soft-spi driver, the management of this pin is done through this simple gpio driver. Even if the main purpose of this driver is to be used by soft-spi, it can still be used as a normal gpio driver but with limitation: for example the first pin can't be used as output. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-12-07gpio: stm32f7: Remove CONFIG_CLK flag.Patrice Chotard
As all STM32 SoCs supports CONFIG_CLK flag, it becomes useless in this driver, remove it. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-07gpio: stm32f7: Move STM32_GPIOS_PER_BANK into gpio.hPatrice Chotard
To allow access to this define by other driver, move it into gpio.h Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-07gpio: stm32f7: Add gpio bank holes managementPatrice Chotard
In some STM32 SoC packages, GPIO bank has not always 16 gpios. Several cases can occur, gpio hole can be located at the beginning, middle or end of the gpio bank or a combination of these 3 configurations. For that, gpio bindings offer the gpio-ranges DT property which described the gpio bank mapping. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-11-29gpio: dwapb_gpio: fix binding without bank-name propertySimon Goldschmidt
As a preparation for merging the socfpga gen5 devicetree files from Linux, this patch makes the dwapb gpio driver work correctly without the 'bank-name' property on the gpio-controller nodes. This property is not present in the Linux drivers and thus is not present in the Linux devicetrees. It is only used to access pins via bank name. This fallback is necessary since without it, the driver will return an error code which will lead to an error in U-Boot startup. The bank names will still be added to the default board device trees in follow-up patch, but other boards using this driver and not including the bank name should also work with the socfpga.dtsi without adding the bank-name property. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-18gpio: Add MT7621 GPIO supportStefan Roese
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on MT7688 (Gardena smart-gateway). The driver is loosly based on the Linux kernel version. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> [fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned'] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-11-16gpio: stm32f7: Add ops get_functionPatrice Chotard
This patch adds gpio get_function ops support. This function reports the state of a gpio. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-11-16gpio: pca953x: Clear the polarity invert register at initYe Li
The pca953x_gpio driver uses default value of polarity inversion register. For some devices like PCA9557 and MAX7310, their polarity inversion register default value is 0xf0. So for high 4 ports, when reading their values, the values are inverted as the actual level. This patch clears the polarity inversion register to 0 at init, so that the port read and write values are aligned. Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2018-11-14gpio: Remove DM_FLAG_PRE_RELOC flag in various driversBin Meng
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be bound before relocation. However due to a bug in the DM core, the flag only takes effect when devices are statically declared via U_BOOT_DEVICE(). This bug has been fixed recently by commit "dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in lists_bind_fdt()", but with the fix, it has a side effect that all existing drivers that declared DM_FLAG_PRE_RELOC flag will be bound before relocation now. This may expose potential boot failure on some boards due to insufficient memory during the pre-relocation stage. To mitigate this potential impact, the following changes are implemented: - Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver only supports configuration from device tree (OF_CONTROL) - Keep DM_FLAG_PRE_RELOC flag in the driver only if the device is statically declared via U_BOOT_DEVICE() - Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for drivers that support both statically declared devices and configuration from device tree Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-11-14gpio: pca953x_gpio: fix DT GPIO flags translationAnatolij Gustschin
Commit fb01e07a95 accidentally broke initialisation of GPIO descriptor flags from device tree: currently the active low flag from gpio-specifier is always ignored. Fix it. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Mario Six <mario.six@gdsys.cc>
2018-10-25Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imxTom Rini
Merged imx8 architecture, fix build for imx8 + warnings
2018-10-22gpio: mxc_gpio: add support for i.MX8Peng Fan
Add i.MX8 support, there are 8 GPIO banks. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2018-10-10gpio: da8xx: Push generic defines of gpio.h out of mach-davinciKeerthy
Push generic defines of gpio.h out of mach-davinci to drivers/gpio now that non-davinci architectures are beginning to use this IP. Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Fix calimain build] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-10gpio: da8xx: Add k2g compatibleKeerthy
Add k2g compatible so that k3 SoCs can be supported Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-10-03gpio: dwapb_gpio: Change to use devm_kcalloc()Ley Foon Tan
Change to use managed resource function devm_kcalloc(), so it will auto free memory when driver is removed. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-09-15gpio: dwapb_gpio: Change to use dev_read_addr()Ley Foon Tan
This changes the driver to use dev_read_addr() which is safe both for flat trees and live trees. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-09-15gpio: dwapb_gpio: Add reset ctrl to driverLey Foon Tan
Add code to reset all reset signals as in gpio DT node. A reset property is an optional feature, so only print out a warning and do not fail if a reset property is not present. If a reset property is discovered, then use it to deassert, thus bringing the IP out of reset. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-09-15gpio: dwapb_gpio: Enable get_function supportLey Foon Tan
Enabled get_function support for dwapb where the function will return the state of GPIO port. Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-09-11DM: omap_gpio: Reduce overhead when used with OF_PLATDATAAdam Ford
Platforms with limited resources in SPL may enable OF_PLATDATA, this limits some of the library functions and cannot extract data from the device tree. This patch adds additional wrappers around these functions to only allow them when OF_CONTROL is enabled and OF_PLATDATA is not. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11GPIO: omap_gpio: Fix gpio name names with device treeAdam Ford
The GPIO bank numbers do not appear in the device tree, so this patch makes the gpio name based on the address (ie gpio@49054000_31 vs gpio4_31) adam Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2018-09-11dm: gpio: da8xx_gpio: Add support for GPIO_ACTIVE_LOW/HIGHAdam Ford
With DM and device tree support, let's use the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW from the device tree as they are intended. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11DM: GPIO: Fix da8xx GPIO indexing over GPIO 32Adam Ford
The GPIO banks are broken up into two 16-bit registers for each bank set. Unfortunately, the math that determines how to shift blindly shifted by the number of the gpio. This worked for gpio numbers under 32, but higher gpio's are broken. This fixes the gpio index, so the bank is passed and the shift amount within the register is passed now instead of the gpio number. Fixes: 8e51c0f25406("dm: gpio: Add DM compatibility to GPIO driver for Davinci") Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-10gpio: stm32f7: replace ODR update by BSRR writePatrice Chotard
Replace clrsetbits on ODR register (2 operations: one read + one write) by writing on the correct bit (SET or RESET) of the BSRR register (only 1 write operation). Moreover this register if safe for simultaneous access by 2 master on the bus. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-08-07gpio: xilinx: Add support for using label propertyMichal Simek
Add support for reading label property from DT and set up bank name based on that. If label property is not present full device node name is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2018-08-07gpio: xilinx: Return 0 from xilinx_gpio_set_valueMichal Simek
.set_value functions have no specified return value and gpio_uclass is not working with it too. But this patch is returning 0 to be in sync with others DM gpio drivers. Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2018-08-07gpio: xilinx: Not read output values via regsMichal Simek
Reading registers for finding out output value is not working because input value is read instead in case of tristate. Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2018-08-07gpio: xilinx: Simplify logic in xilinx_gpio_set_valueMichal Simek
There is no reason to do read/write for if/else separately. Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2018-08-07gpio: xilinx: Set value before changing directionMichal Simek
Set a value before changing gpio direction. This will ensure that the old value is not propagated when direction has changed but new value is not written yet. Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2018-08-07gpio: xilinx: Remove !DM driverMichal Simek
There is no user for !DM driver that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-07gpio: xilinx: Find out bank before use in xilinx_gpio_get_function()Michal Simek
Call xilinx_gpio_get_bank_pin() before use. Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2018-08-06gpio: zynq: Used platdata structure for storing static data instead of privVipul Kumar
This patch used platdata structure instead of priv for storing static information read from DT. Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-31GPIO: CREG: improve flexibility of hsdk-creg-gpio driverEugeniy Paltsev
CREG GPIO is a driver for weird soc-specific output ports, which are controlled by some fields in memory mapped register. Example: 31 9 7 5 0 < bit number | | | | | [ not used | gpio-1 | gpio-0 | <-shift-> ] < 32 bit register ^ ^ | | write 0x2 == set output to "1" (activate) write 0x3 == set output to "0" (deactivate) As of tooday we only support fixed (hardcoded) bit per gpio line, activate / deactivatei and shift values. Fix that by read them from device tree to be able to use this driver for other boards. Remove "hsdk" prefix from compatible string as this driver can be used with different boards like HSDK, AXS101, AXS103, etc. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-07-23Convert CONFIG_DA8XX_GPIO to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_DA8XX_GPIO Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-19microblaze: Convert generic platform to DM gpioMichal Simek
Converting GPIO to DM requires to do changes in reset subsystem that's why support for Microblaze soft reset via sysreset and GPIO sysreset support was added. These two patches enables enabling GPIO DM. Microblaze soft reset is bind at last reset method. GPIO reset is handled via sysreset with adding this fragment to DT. gpio-restart { compatible = "gpio-restart"; gpios = <&reset_gpio 0 0 0>; /* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */ }; hard-reset-gpio property is not documented and also handled. Conversion is required. Unfortunately do_reset is required for SPL that's why use only soft microblaze reset for now. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19gpio: xilinx: Convert driver to DMMichal Simek
This patch is enabling GPIO_DM support to have an option to use this driver together with zynq gpio driver. !DM part is kept there till Microblaze is cleanup which will be done hopefully soon. Just a note: There is no reason to initialize uc-priv->name because it is completely unused. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19gpio: zynq: Setup bank_name to dev->nameMichal Simek
There should be proper bank name setup to distinguish between different gpio drivers. Use dev->name for it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19gpio: zynq: Read of mach data in platdata with dev_get_driver_dataMichal Simek
Remove bogus zynq_gpio_getplat_data() and read driver data directly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19gpio: dm: Support manual relocation for gpioMichal Simek
Relocate gpio ops as was done by: "dm: Add support for all targets which requires MANUAL_RELOC" (sha1: 484fdf5ba058b07be5ca82763aa2b72063540ef3) Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19gpio: zynq: Fix typo in one error messageMichal Simek
Just fix error message. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19gpio: zynq: Use live-tree functionMichal Simek
Use live-tree function. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-10gpio: omap_gpio: Convert to auto-alloc feature when DT is supportedAdam Ford
The omap_gpio driver has a TODO that says when every board is converted to DM and DT, the omap_gpio_bind can stop using calloc and switch to auto-alloc. This patch converts this driver to auto-calloc when DT is enabled. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-27Merge git://git.denx.de/u-boot-imxTom Rini
2018-06-18gpio: omap_gpio: Name GPIO's by bank and index with DM_GPIOAdam Ford
There are multiple GPIO banks with up to 32 pins / bank. When using 'gpio status -a' to read the pins, this patch displays both GPIO<bank>_<index> similar to how the device trees display in addition to displaying gpio_# Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-18dm: gpio: Add DM compatibility to GPIO driver for DavinciAdam Ford
This adds DM_GPIO support for the davinici GPIO driver with DT support. Signed-off-by: Adam Ford <aford173@gmail.com>
generated by cgit (git 2.34.1) at 2024-12-25 15:39:23 +0000