| Age | Commit message (Collapse) | Author |
|---|
|
Currently, the entry "bus-width = <8>" in the ZynqMP's sdhci nodes
is not evaluated. This results in the bus width staying at its default
value (4 bit in HS200 mode).
Fix this by calling mmc_of_parse. This function also checks for the
"no-1-8-v" and "max-frequency" entries. Remove the handling of those
nodes from this driver.
Signed-off-by: Benedikt Grassl <Benedikt.Grassl@rohde-schwarz.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
RPMB support is used by the 'mmc rpmb' command and by the OP-TEE support.
We do not need it in SPL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Implement get_b_max() for the Renesas R-Car SDHI controller driver, limit
the b_max per hardware capabilities such that select Gen2 controllers have
16bit block transfer limit, the rest has 32bit block transfer limit and on
Gen3, the block transfer limit on addresses above the 32bit boundary is set
to 1/4 of the malloc area.
Originally, on Gen3, the block transfers above the 32bit area were limited
to PIO only, which resulted in (R8A7795 Salvator-X , HS200 eMMC):
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.151 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 11.090 seconds
with bounce buffer in place and b_max adjustment in place:
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.156 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 2.349 seconds
Note that the bounce buffer does mallocate and free the bounce buffer
for every transfer. Experiment which removes this results in further
increase of read speed, from 2.349s to 2.156s per 512 MiB of data,
which is not such a significant improvement anymore. It might however
be interesting to have bounce buffer directly in the MMC core or even
block core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
Add getter function which permits adjusting the maximum number of
blocks that could be read in a single sustained read transfer based
on the location of the source/target buffer and length, before such
transfer starts.
This is mainly useful on systems which have various DMA restrictions
for different memory locations, e.g. DMA limited to 32bit addresses,
and where a bounce buffer is used to work around such restrictions.
Since the U-Boot bounce buffer is mallocated, it's size is limited
by the malloc area size, and the read transfer to such a buffer must
also be limited. However, as not all areas are limited equally, the
b_max should be adjusted accordinly as needed to avoid degrading
performance unnecessarily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
The R-Car SDHI DMA controller has various restrictions. To work around
those restrictions without falling back to PIO, implement bounce buffer
with custom alignment check function which tests for those limitations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
move host.mmc before sdhci_setup_cfg
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
|
|
set_ios_post return type changed from void to int, correcting
the same to fix compilation warning.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
|
|
Enable SDHCI_QUIRK_BROKEN_R1B quirk.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
|
|
Free the pointer variable 'iproc_sdhci' upon failure to fix
possible memory leak.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
|
|
Provide command 'mmc wp' to power on write protect boot areas on eMMC
devices.
The B_PWR_WP_EN bit in the extended CSD register BOOT_WP is set. The boot
area are write protected until the next power cycle occurs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Export function mmc_send_ext_csd() for reading the extended CSD register.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
In R-Car Gen 3, there is a DMA controller restriction of SDHI.
When the transfer exceeding the 4 kByte boundary is performed while
the DRAM address is not 128 byte aligned, the bus is occupied.
This patch avoids this.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Until now, the mmc clock was left in a good enough state by the ROM
code to be used by the controller. However on some SoC, if the ROM
code finds a bootloader on USB or SPI, it might leave the MMC clock
in state the controller cannot work with.
Enable the input clocks provided to the mmc controller. While the
u-boot mmc controller driver is not doing fancy settings like the Linux,
it at least needs to make these clocks are running.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The 4 bit MMC controllers have an internal debounce for the SDCD line
with a debounce delay of 1 second. Therefore, after clocks to the IP are
enabled, software has to wait for this time before it can power on the
controller.
Add a deferred_probe() callback which polls on sdcd for a maximum of 2 seconds
before switching on power to the controller or (in the case of no card)
returning a ENOMEDIUM. This pushes the 1 second wait time to when the
card is actually needed rather than at every probe() making sure that
users who don't insert an SD card in the slot don't have to wait such a
long time.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
MMC_LEGACY & SD_LEGACY are not differentiated timings in the spec and
don't have any meaningful differences. Therefore, get rid of all
references to SD_LEGACY and use MMC_LEGACY to mean both of them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add the sdhci_deferred_probe() function to register as the
deferred_probe() callback to the mmc core. It will in turn call the
deferred_probe() callback of the platform drivers as declared in the
sdhci_ops.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Add a deferred_probe() API for platforms that want to do some
configurations just before starting to enumerate the device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
|
|
This driver currently performs cache operation before the DMA start,
but does nothing after the DMA completion.
When reading data by DMA, the cache invalidation is needed also after
finishing the DMA transfer. Otherwise, the CPU might read data from
the cache instead of from the main memory when speculative memory read
or memory prefetch occurs.
Instead of calling the cache operation directly, this commit adds
dma_unmap_single(), which performs cache invalidation internally,
but drivers do not need which operation is being run.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, sdhci_prepare_dma() calls flush_cache() regardless of the
DMA direction.
Actually, cache invalidation is enough when reading data from the device.
This is correctly handled by dma_map_single(), which mimics the DMA-API
in Linux kernel. Drivers can be agnostic which cache operation occurs
behind the scene.
This commit also sanitizes the difference between the virtual address
and the dma address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
host->mmc is already (struct mmc *).
memalign() returns an opaque pointer, so there is no need for casting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Use {lower,upper}_32_bits() instead of the combination of cast
and shift.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The same code is run for both SDHCI_QUIRK_32BIT_DMA_ADDR and
define(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER).
Unify the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Using the global variable does not look nice.
Add a new field sthci::align_buffer to point to the bounce buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
dma_unmap_single() takes the dma address, not virtual address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The reference manuals for MPC8308 and MPC8309 both say that the
esdhcctl aka DMA Control Register "is implemented as SDHCCR" in the
System configuration registers. Unfortunately, that doesn't mean that
the registers are just mirrors of each other - any write to esdhcctl
is simply ignored. So to actually enable cache snooping, we
unfortunately have to add a little ifdeffery.
There is, naturally, no description of the bit fields of esdhcctl in
the MPC8309 manual, but comparing the description of esdhcctl from the
LS1021A reference manual to the description of the sdhccr in MPC8309,
one also finds that the fields are bit-reversed, so the bit to set is
0x02000000 rather than 0x00000040 - this is also what board_mmc_init()
uses in the two gdsys/mpc8308/ boards.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
These functions are defined before the callers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Since commit 01298da31d92 ("mmc: Change mode when switching to a boot
partition"), errors in mmc_select_mode_and_width() are ignored.
The return value should be checked.
Fixes: 01298da31d92 ("mmc: Change mode when switching to a boot partition")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
erase_grp_size is used, when MMC_WRITE is enabled.
- error: ‘struct mmc’ has no member named ‘erase_grp_size’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
If the host has Broken R1B, use only R1 response type.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
- Various exynos fixes
|
|
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Read generic MMC properties from device-tree. This allows to specify for
example cd-inverted property and let MMC core to properly handle such
case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
|
|
Add Support for writing to PHY registers for J721e. There are number of
differences between the J721e 8 bit PHY, J721e 4 bit PHY and AM654 PHY.
Create a driver_data structure with an ops and flags field and use the
flags field to indicate these differences. The differences are as
follows:
1. The J721e 4 bit instance PHY does not have a DLL. Introduce a
DLL_PRESENT flag to make sure that DLL related registers are accessed
only where they are present. Also add a separate set_ios_post()
callback.
2. The J721e 8 bit instance is not muxed with anything else inside the
SoC and hence the IOMUX_ENABLE filed does not exist. Add a flag which is
used to indicate the presence of this field.
3. The register field used to select DLL frequency is 3 bit wide in
J721e as compared to 2 bits in AM65x. Add another flag that
distinguishes these fields.
4. The strobe select field is 8 bit wide as compared to 4 bit wide for
AM65x. Add yet another flag to indicate this difference. Strobe select
is used only for HS400 speed mode, support for which has not been added
in AM65x.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Cleanup of fsl_esdhc driver together with arch/defconfig change
- Add quirk for APP_CMD retry
|
|
This patch add mmc and sd support for Mediatek MT7622 SoCs
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
|
|
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
|
|
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
|
|
Fix typo in description of MMC_QUIRKS config option.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
|
