summaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)Author
2019-10-10spl: dm_mmc: Initialize only the required mmc deviceLokesh Vutla
In SPL, all the available mmc devices gets initialized during boot. This might not work in cases where clocks are not available for certain mmc devices(other than boot device) and the support for enabling device might not be ready. Texas Instruments' K3 J721E device having a central system controller (dmsc) is one such example falling in this category. Below is the sequence for the failing scenario: - ROM comes up in SD mode and loads SPL by just initialing SD card. - SPL loads dmsc firmware from SD Card. Since ROM has enabled SD, SPL need not enable the SD, just need to re initialize the card. But SPL is trying to initialize other MMC instances which are in disabled state. Since dmsc firmware is not yet available, devices cannot be enabled. So in SPL, initialize only the mmc device that is needed. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-09Merge tag 'xilinx-for-v2020.01' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 FPGA: - Enable fpga loading on Versal - Minor fix Microblaze: - Fix LMB configurations to support initrds - Some other cleanups Zynq: - Minor config/dt changes - Add distro boot support for usb1 and mmc1 - Remove Xilinx private boot commands and use only distro boot ZynqMP: - Kconfig cleanups, defconfig updates - Update some dt files - Add firmware driver for talking to PMUFW - Extend distro boot support for jtag - Add new IDs - Add system controller configurations - Convert code to talk firmware via mailbox or SMCs Versal: - Add board_late_init() - Add run time DT memory setup - Add DFU support - Extend distro boot support for jtag and dfu - Add clock driver - Tune mini configurations Xilinx: - Improve documentation (boot scripts, dt binding) - Enable run time initrd_high calculation - Define default SYS_PROMPT - Add zynq/zynqmp virtual defconfig Drivers: - Add Xilinx mailbox driver for talking to firmware - Clean zynq_gem for Versal - Move ZYNQ_HISPD_BROKEN to Kconfig - Wire genphy_init() in phy.c - Add Xilinx gii2rgmii bridge - Cleanup zynq_sdhci - dwc3 fix - zynq_gpio fix - axi_emac fix Others: - apalis-tk1 - clean config file
2019-10-09Merge tag 'u-boot-imx-20191009' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191009 ------------------- Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532 - MX6UL / ULZ - Toradex board - Allow to set OCRAM for MX6Q/D - MX7ULP - MX8: (container image, imx8mq_mek), SCU API - fix several board booting from SD/EMMC (cubox-i for example) - pico boards [trini: display5 merged manually] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Rename existing FSP code to fsp1 - Add fsp2 directory in preparation to support FSP 2.0 - Various x86 platform codes update - Various bug fixes and updates in dm core, sandbox and spl
2019-10-08mmc: Replace printf with debug call for timeouts in the i.MX28 mxs driverLukasz Majewski
This change replaces printf() with debug() for the notification about commands timeouts. This is done on purpose (also other drivers use such approach - dw_mmc.c, mvebu_mmc.c), as the mmc core code (mmc.c) uses timeouts to assess if one is using sd card or eMMC device. In such situation timeout is a some kind of a "normal" behavior and there shall not be any output to the console. There is no impact on boot time for boards using this driver (even in SPL) when two extra timeouts are returned (no SD card present, only eMMC available). Boot time tested with grabserial: sudo grabserial -b 115200 -d /dev/ttyUSB1 -e 30 -t -m "^U-Boot SPL*" Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08mmc: Convert mxsmmc eMMC driver for i.MX2{38} to DM/DTSLukasz Majewski
This patch converts the mxsmmc driver to support DM/DTS. Moreover, it is also possible to use it in early SPL with SPL_OF_PLATDATA enabled. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08mmc: zynq_sdhci: Remove check for DM_MMC configSiva Durga Prasad Paladugu
The zynq_sdhci drivers depends on DM_MMC in Kconfig so no need to check for DM_MMC in the driver so this patch removes it. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08mmc: sdhci: Move ZYNQ_HISPD_BROKEN to KconfigSiva Durga Prasad Paladugu
This patch moves CONFIG_ZYNQ_HISPD_BROKEN to Kconfig Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08mmc: atmel_sdhci: Add sam9x60-sdhci compatibility stringSandeep Sheriker Mallikarjun
Add new compatibility string for matching sam9x60 product. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2019-10-08spl: Allow tiny printf() to be controlled in SPL and TPLSimon Glass
At present there is only one control for this and it is used for both SPL and TPL. But SPL might have a lot more space than TPL so the extra cost of a full printf() might be acceptable. Split the option into two, providing separate SPL and TPL controls. The TPL setting defaults to the same as SPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08sandbox: mmc: Fix up MMC emulator for valgrindSimon Glass
At present running sandbox with valgrind produces some warnings due to the MMC emulator not filling in all the expected fields. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: use sizeof() instead of hardcoded 16] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-12mmc: fsl_esdhc: Add emmc hs200 supportYinbo Zhu
Add eMMC hs200 mode for ls1028a, ls1012a, lx2160a. This increases eMMC performance. Tuning procedure is currently not supported. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12mmc: Kconfig: Add FSL_ESDHC_USE_PERIPHERAL_CLK optionYinbo Zhu
NXP fsl_esdhc controller supports two reference clocks: platform clock and peripheral clock Peripheral clock can provide higher clock frequency which is required to be used for tuning of SD UHS mode and eMMC HS200/HS400 modes. Peripheral clock is enabled by default by defining config option FSL_ESDHC_USE_PERIPHERAL_CLK if eMMC HS200/HS400 modes are supported. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-08Merge tag 'mmc-9-6-2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
Bug fixes to mmc_spi Add Aspeed SD driver Fix dw_mmc timeout calculation Fix timeout values passed to mmc_wait_dat0 sdhci dt caps/mask update [trini: Fix evb-ast2500_defconfig CONFIG_MMC line] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-06Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-bootTom Rini
- fix mailbox status register used for polling - fix bcm2835_sdhost to wait long enough for a transfer to complete - increase kernel image size from 8 MB to 64 MB on arm64 - add support for RPi4 - add prefixes for raspberry pi related stuff to git-mailrc
2019-09-06mmc: bcm283x: Add support for bcm2711 device in bcm2835_sdhciMatthias Brugger
The bcm2711 has two emmc controllers. The difference is the clocks they use. Add support for the second emmc controller. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: Andrei Gherzan <andrei@balena.io>
2019-09-06mmc: bcm2835-host: Fix wait_transfer_completeRaul Benet
Function bcm_2835_wait_transfer_complete() is not waiting long enough. The previous code was claiming to wait for ~1 seconds, but as it depends on register reads it's time actually varies. Some cards require wait times of up to ~56 ms to perform the command 'saveenv' on an EXT4 partition. Re-implement the loop exit condition to use get_timer() which allows to specify the wait time in more reliable manner. Set the maximum wait time to the originally intended 1 second. Signed-off by: Raul Benet <raul.benet_at_kaptivo.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-06mmc: sdhci: Add support for dt caps & caps maskT Karthik Reddy
The sdhci capabilities registers can be incorrect. The sdhci-caps-mask and sdhci-caps dt properties specify which bits of the registers are incorrect and what their values should be. This patch makes the sdhci driver use those properties to correct the caps. Also use "dev_read_u64_default" instead of "dev_read_u32_array" for caps mask. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-09-05dm: mmc_spi: Fix NULL pointer dereference in mmc_spi_bind()Bin Meng
The mmc_spi driver's priv is not available in its bind phase(). Use platdata instead. Fixes: 05e35d429745 ("mmc: mmc_spi: Re-write driver using DM framework") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-09-05mmc: dw_mmc: fix timeout calculate methodKever Yang
There are two cases not been considered: - use uint for timeout, it will overflow when size bigger than 512KB for it *8*1000 at the beginning, but we may use size up to 32MB; The 'timeout' will overflow if size bigger than 51.2MB after this fix, which should be enough for U-Boot; - The timeout is using clock speed for data rate, but the device may not have such high speed, eg. clock is 52MHz while the device write speed may be less than 10MB/s, and we may use up to 150MHz clock. Fix them in this patch, the max timeout is about 6500 when size is 32MB after fix. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-05mmc: Add Aspeed SD controller driverEddie James
Add support for the Aspeed SD host controller engine. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Cédric Le Goater <clg@kaod.org>
2019-09-05mmc: Rename timeout parameters for clarificationSam Protsenko
It's quite hard to figure out time units for various function that have timeout parameters. This leads to possible errors when one forgets to convert ms to us, for example. Let's rename those parameters correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues further. While at it, add time units info as comments to struct mmc fields. This commit doesn't change the behavior, only renames parameters names. Buildman should report no changes at all. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
2019-09-05mmc: Fix timeout values passed to mmc_wait_dat0()Sam Protsenko
mmc_wait_dat0() expects timeout argument to be in usec units. But some overlying functions operate on timeout in msec units. Convert timeout from msec to usec when passing it to mmc_wait_dat0(). This fixes 'avb' commands on BeagleBoard X15, because next chain was failing: get_partition() -> mmc_switch_part() -> __mmc_switch() -> mmc_wait_dat0() when passing incorrect timeout from __mmc_switch() to mmc_wait_dat0(). Fixes: bb98b8c5c06a ("mmc: During a switch, poll on dat0 if available and check the final status") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com> Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Igor Opaniuk <igor.opaniuk@gmail.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
2019-09-05dm: mmc: remove unused U_BOOT_DRIVER(mmc)Andy Yan
When look through the code, I found this bare metal drives is not used, so remove it. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-08-30mmc: invalidate block cache after hwpart switched successfullyWeijie Gao
eMMC device has multiple hw partitions both address from zero. However the mmc driver lacks block cache invalidation for switch hwpart. This causes a problem that data of current hw partition is cached before switching to another hw partition. And the following read operation of the latter hw partition will get wrong data when reading from the addresses that have been cached previously. To solve this problem, invalidate block cache after a successful mmc_switch_part() operation. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Tested-by: Felix Brack <fb@ltec.ch>
2019-08-27mmc: stm32_sdmmc2: reload watchdogChristophe Kerello
This patch solves a watchdog reset issue during mmc erase command. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27mmc: sti_sdhci: Fix sdhci_setup_cfg() call.Patrice Chotard
host->mmc, host->mmc->dev and host->mmc->priv must be set before calling sdhci_setup_cfg() to avoid hang during mmc initialization. Thanks to commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") which put this issue into evidence. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-27mmc: stm32_sdmmc2: Increase SDMMC_BUSYD0END_TIMEOUT_USPatrice Chotard
Increase SDMMC_BUSYD0END_TIMEOUT_US from 1s to 2s to avoid timeout error during blocks erase on some sdcard Issue seen on Kingston 16GB : Device: STM32 SDMMC2 Manufacturer ID: 27 OEM: 5048 Name: SD16G Bus Speed: 50000000 Mode: SD High Speed (50MHz) card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed (50MHz)] host capabilities: widths [4, 1] modes [MMC legacy, SD Legacy, MMC High Speed (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)] Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 14.5 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes Issue reproduced with following command: STM32MP> mmc erase 0 100000 MMC erase: dev # 0, block # 0, count 1048576 ... mmc erase failed 16384 blocks erased: ERROR By setting SDMMC_BUSYD0END_TIMEOUT_US at 2 seconds and by adding time measurement in stm32_sdmmc2_end_cmd() as shown below: +start = get_timer(0); /* Polling status register */ ret = readl_poll_timeout(priv->base + SDMMC_STA, status, status & mask, SDMMC_BUSYD0END_TIMEOUT_US); +printf("time = %ld ms\n", get_timer(start)); We get the following trace: STM32MP> mmc erase 0 100000 MMC erase: dev # 0, block # 0, count 1048576 ... time = 17 ms time = 1 ms time = 1025 ms time = 54 ms time = 56 ms time = 1021 ms time = 57 ms time = 56 ms time = 1020 ms time = 53 ms time = 57 ms time = 1021 ms time = 53 ms time = 57 ms time = 1313 ms time = 54 ms time = 56 ms time = 1026 ms time = 54 ms time = 56 ms time = 1036 ms time = 54 ms time = 56 ms time = 1028 ms time = 53 ms time = 56 ms time = 1027 ms time = 54 ms time = 56 ms time = 1024 ms time = 54 ms time = 56 ms time = 1020 ms time = 54 ms time = 57 ms time = 1023 ms time = 54 ms time = 56 ms time = 1033 ms time = 53 ms time = 57 ms .... time = 53 ms time = 57 ms time = 1021 ms time = 56 ms time = 56 ms time = 1026 ms time = 54 ms time = 56 ms 1048576 blocks erased: OK We see that 1 second timeout is not enough, we also see one measurement up to 1313 ms. Set the timeout to 2 second to keep a security margin. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-08-23Convert CONFIG_FSL_USDHC to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-20mmc: mtk-sd: Add MT8183 SoC supportFabien Parent
Add support for the MT8183 in the MediaTek MMC driver. Signed-off-by: Fabien Parent <fparent@baylibre.com>
2019-08-11mmc: Add support for HI3660 SoC reusing hi6220_dw_mmc driverManivannan Sadhasivam
This commit adds MMC driver support for HI3660 SoC reusing hi6220_dw_mmc driver. Since HI3660 operates at different clock rate and uses fifo mode now, let's introduce the platform data and utilize it for different SoCs supported by this driver. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-08-09mmc: Move tegra loopback disable option to be under tegraTrent Piepho
This is a configuration option specific to the tegra controller. Doing it this way makes it show up directly under the tegra controller option, indented one level, as "Disable external clock loopback". The way it is now, it shows up at the end of the controller list, not indented, as if it's some kind of generic MMC configuration option. Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Simon Glass <sjg@chromium.org> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09Merge tag 'mmc-8-9' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
- mmc test fix - sdhci driver fix
2019-08-09Merge tag 'u-boot-rockchip-20190809' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Add rk3399 boards Khadas Edge/-V/-Captain - Add fully souce code support for rk3328 including TPL/DRAM init - Enable boot from eMMC for rk3399 rock960/ficus boards - turn on the IO supply for dw_mmc
2019-08-09mmc: tangier_sdhci: fix uninitialized pointer deref on probePeng Fan
Commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-08-09mmc: sdhci-cadence: fix uninitialized pointer deref on probePeng Fan
Commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-08-09mmc: s5p: fix uninitialized pointer deref on probePeng Fan
Commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-08-09mmc: pci: fix uninitialized pointer deref on probePeng Fan
Commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-08-09mmc: msm_sdhci: fix uninitialized pointer deref on probePeng Fan
Commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-08-09mmc: bcm: fix uninitialized pointer deref on probePeng Fan
Commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Matthias Brugger <mbrugger@suse.com> Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-08-09mmc: atmel_sdhci: fix uninitialized pointer deref on probePeng Fan
Commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-08-09mmc: zynq_sdhci: fix uninitialized pointer deref on probeMatwey V. Kornilov
Since commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Move the mmc field initialization before sdhci_setup_cfg() call to avoid crash on mmc pointer dereference. [this patch is based on commit 41a9fab8dac8 ("mmc: mv_sdhci: fix uninitialized pointer deref on probe") by Baruch Siach] Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu102/zc706)
2019-08-09mmc: Select SPL_HS200_SUPPORT if SPL_HS400_SUPPORT is selectedFaiz Abbas
Select SPL_HS200_SUPPORT if SPL_HS400_SUPPORT is selected as is being done for the U-boot case. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-31mmc: relocate code commentBaruch Siach
The comment about init op being NULL used to be next to the NULL check code. Commit 8ca51e51c182 ("dm: mmc: Add a way to use driver model for MMC operations") separated the comment from the code. Put them back together. Fixes: 8ca51e51c182 ("dm: mmc: Add a way to use driver model for MMC operations") Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-31mmc: mtk-sd: add WATCHDOG_RESET() to prevent watchdog timeoutWeijie Gao
When reading large data in once (reading 512MiB is tested on MT7623), a watchdog timeout is triggered due to watchdog not being fed. This patch adds WATCHDOG_RESET() to msdc_start_data() so the watchdog will be fed every 1024 blocks are read/written. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-07-31mmc: sdhci: fix chip detect gpio property nameBaruch Siach
The standard property name for chip-detect gpio is "cd-gpios". All in-tree DT files use only this name. Fixes: 451931ea700 ("mmc: sdhci: Read cd-gpio from devicetree") Cc: T Karthik Reddy <t.karthik.reddy@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-31mmc: mv_sdhci: fix uninitialized pointer deref on probeBaruch Siach
Since commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc field. Move the mmc field initialization before sdhci_setup_cfg() call to avoid crash on mmc pointer dereference. Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2019-07-31dw_mmc: turn on the IO supplyUrja Rannikko
Fixes the microSD slot on the ASUS C201. Signed-off-by: Urja Rannikko <urjaman@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com<mailto:peng.fan@nxp.com>>
2019-07-27Merge branch '2019-07-26-ti-imports'Tom Rini
- Bring in the rest of the J271E platform - Various OMAP3/AM3517, DA850 fixes
2019-07-27Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-spiTom Rini
- fix for fsl_qspi read timeout (Thomas) - spi-mem read data size fix (Ye Li) - SiFive SPI driver, mmc_spi flags (Bhargav, Anup) - Micron spi-nor parts (Ashish) - MT7629 spi-mem driver(Weijie)
generated by cgit (git 2.34.1) at 2025-01-08 03:08:31 +0000