| Age | Commit message (Collapse) | Author |
|---|
|
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
|
|
It is not possible to link the SPL image when CONFIG_GPIO is enabled
but CONFIG_SPL_GPIO is not. Use the IS_ENABLED macro instead to
correctly check whether CONFIG_{SPL_}GPIO is enabled.
This commit fixes the following errors:
* undefined reference to `dm_gpio_get_value
* undefined reference to `gpio_request_by_name'
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[trini: Move guard to fix warning in msdc_ops_get_wp()]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The code is checking for incomplete read when it see the INT_XFER_COMPL
flag, but it forget to first check whether there is anything left in the
FIFO to copy to the RX buffer. This means that sometimes we will get
errors because of erroneous incomplete read operation.
This commit fixes the driver re-ordering the code so that we first
check for data inside the RX fifo and only after check the status
of the INT_XFER_COMPL flag.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
|
|
It adds compatible "hisilicon,hi3798cv200-dw-mshc" for Poplar SoC
Hi3798CV200 to probe this mmc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
This variable was incorrectly added by:
"mmc: zynq_sdhci: Add support for SD3.0"
(sha1: d1f4e39d58db32a4fd1a1b4085e0ede498bd773f)
which had nothing to do with MMC power sequence provider.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
|
|
Add TFA boot flow for more boards
Add TFA boot defconfig for ls1088a and ls2088a.
Add dts fixup for PCIe endpoint and root complex.
|
|
- MIPS: mscc: various enhancements for Luton and Ocelot platforms
- MIPS: mscc: added support for Jaguar2 platform
- MIPS: optimised SPL linker script
- MIPS: bcm6368: fix restart flow issues
- MIPS: fixed CONFIG_OF_EMBED warnings for all MIPS boards
- MIPS: mt7688: small fixes and enhancements
- mmc: compile-out write support if disabled
|
|
This patch is to make get_cd work well when DM_MMC enabled
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Do not build write support, unless it's enabled.
In the SPL case, this change will typically remove
precious bytes (as write support is most often
not needed in SPL).
This is important on this platform, where the maximum
SPL size is 14 KiB.
With gcc v7.3, this change saves 144 bytes producing:
size spl/u-boot-spl
text data bss dec hex filename
9240 752 712 10704 29d0 spl/u-boot-spl
To make the code easier to compile-out and more
readable, a pair of read_data/write_data helpers are created.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Use CONFIG_IS_ENABLED(BLK) instead of CONFIG_BLK,
in order to fix the following build issues when
CONFIG_SPL_MMC_WRITE is selected:
drivers/mmc/mmc_write.c:69:7: error: conflicting types for 'mmc_berase'
ulong mmc_berase(struct udevice *dev, lbaint_t start, lbaint_t blkcnt)
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:39:7: note: previous declaration of 'mmc_berase' was here
ulong mmc_berase(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt);
^~~~~~~~~~
drivers/mmc/mmc_write.c:187:7: error: conflicting types for 'mmc_bwrite'
ulong mmc_bwrite(struct udevice *dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:37:7: note: previous declaration of 'mmc_bwrite' was here
ulong mmc_bwrite(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.
In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.
However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The following hang is observed on a Hummingboard 2 MicroSOM
i2eX iMX6D - rev 1.3 with no eMMC populated on board:
U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
Trying to boot from MMC1
U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
CPU: Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
---> hangs
which is caused by the following infinite loop inside esdhc_send_cmd_common()
while (!(esdhc_read32(®s->irqstat) & flags))
;
Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.
Reported-by: Ricardo Salveti <rsalveti@rsalveti.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Ricardo Salveti <rsalveti@rsalveti.net>
|
|
|
|
Existing clock configure code has been followed based on the
legacy MMC dt node definitions and it cannot work with recent
dts(i) sync from Linux.
So, add clock configure code for Allwinner platforms which support
DM_MMC and eventually this will drop once CLK support is in Mainline.
Fixes: 3c92cca3cda0 ("ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> # Gemei G9 A10 Tablet
Tested-by: Marek Kraus <gamelasterv2@gmail.com> # A10-OLinuXino-Lime
|
|
Commit d0851c893706 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC
framework.
However Allwinner is (still) relying on a non-DM MMC driver, so we are
now missing the implicit partition init, leading to failing MMC accesses
due to the missing partition information.
Bring the call back just for non-DM MMC driver to fix this regression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Soeren Moch <smoch@web.de>
|
|
imx for 2019.01
- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x
|
|
Rename mx8m,MX8M to imx8m,IMX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
|
|
Add driver for the JZ47xx MSC controller.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
According to SD Specifications Part 1 Physical Layer Simplified Specification
Version 6.00 August 29, 2018, section 4.3.10 (Switch Function Command) and
section 5.6 (SCR register), SD cards version 1.00 and 1.01 do not support the
SD CMD 6.
Currently, U-Boot will issue CMD 6 unconditionally in sd_set_card_speed()
while configuring the bus for selected frequency. This will make SD cards
version 1.00 and 1.01 time out and thus fail detection altogether.
Fix this by not sending CMD 6 on such cards. Tested on Matsushita Electric
Industrial Co., Ltd. Japan RP-SD008B / Victor 8MB SD card, CU-SD008, which
is correctly detected with this patch as:
Device: sd@ee160000
Manufacturer ID: 1
OEM: 5041
Name: S008B
Bus Speed: 25000000
Mode : SD Legacy
Rd Block Len: 512
SD version 1.0
High Capacity: No
Capacity: 6.5 MiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add support for the HS400 mode to SDHI driver. This uses the up-tune
mechanism from already supported HS200 tuning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Move the tap_pos variable, which is the HS200/HS400/SDR104 calibration
offset, into private data, so it can be passed around. This is done in
preparation for the HS400 mode, which needs to adjust this value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Filter out HS400 support on SoCs where HS400 is not supported yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Reorder the tmio_sd_set_clk_rate() function such that it handles all
of the clock requiests correctly. Specifically, before this patch,
clock request with (mmc->clock == 0 && mmc->clk_disable) could leave
the clock enabled, as the function would exit on if (!mmc->clock)
condition on top and will not handle the mmc->clk_disable at all.
Rather than band-aid fixing just that particular problem, reorder
the entire function to make it easier to understand and verify that
all the cases are covered. The function has three sections now:
First, if mmc->clock != 0, we calculate divider for the SD block.
Second, if mmc->clock != 0 and SD block clock are enabled and
current divider is not equal to the new divider, then
stop the clock and update the divider.
Third, if mmc->clk_disable is set, disable the clock, otherwise
enable the clock. This happens independently of divider
update now.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The TMIO core has a feature where it can automatically disable clock output
when the bus is not in use. While this is useful, it also interferes with
switching the bus to 1.8V and other background tasks of the SD/MMC cards,
which require clock to be enabled.
This patch respects the mmc->clk_disable and only disables the clock when
the MMC core requests it. Otherwise the clock are continuously generated
on the bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The TMIO core has a quirk where divider == 1 must not be set in DDR modes.
Handle this by setting divider to 2, as suggested in the documentation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Switch the driver to using clk_get_rate()/clk_set_rate() instead of
caching the mclk frequency in it's private data. This is required on
the SDHI variant of the controller, where the upstream mclk need to
be adjusted when using UHS modes.
Platforms which do not support clock framework or do not support it
in eg. SPL default to 100 MHz clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
---
V2: - Fix build on certain platforms using SPL without clock framework
V3: - Turn clk_get_rate into a callback and fill it as needed on both
renesas and socionext platforms
|
|
Add HS400 properties parsing support to mmc_of_parse().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
- net: designware: add meson meson compatibles
- Amlogic Meson cleanup for AXG SoC support
|
|
This patch adds MT7623 host controller driver for accessing SD/MMC.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add the compatible string for the upcoming Amlogic AXG SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Comment in Linux driver says that clock needs to be doubled only
if we use DDR modes, moreover divider has to be set accordingly.
U-boot driver doesn't declare support for any DDR modes and doesn't
set internal clock divider in CLKCR, so it doubles clock
unconditionally when new mode is used.
Some cards can't handle that and as result SPL fails to load u-boot.
Fixes: de9b1771c3b ("mmc: sunxi: Support new mode")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
|
|
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
|
|
- virtio implementation and supporting patches
- DM_FLAG_PRE_RELOC fixes
- regmap improvements
- minor buildman and sandbox things
|
|
|
|
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe() method to do it automatically.
Update all DM BLK drivers to adopt this change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
A64 and H6 support automatic delay calibration and Linux driver uses it
instead of hardcoded delays. Add support for it to u-boot driver.
Fixes eMMC instability on Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This patch adds check for command response CRC failure. The driver
is currently ignoring CRC check failure on command resposes which
have CRC atteched to it, which can be potentially dangerous. Even
more grueling problem happens when the command response is followed
by data transfer though, as in that case, the dwmci_data_transfer()
function will spin until it reaches the 240s timeout.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
It is perfectly fine to write th DTCNTL TAP count and enable the
SCC sampling clock operation in the same write.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
When the bus switches to 1.8V mode of operation, it is necessary to
verify that the card correctly initiated and completed the voltage
switch. This is done by reading out the state of DATA0 line.
This patch implement support for reading out the state of the DATA0
line, so the MMC core code can correctly switch to 1.8V mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Make sure to clear HS400 configuration when resetting the SCC block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add check to avoid touching the SCC tuning registers in case the IP
doesn't support them or if the support isn't in place yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Preinitialize the SD card signals regulator to 3.3V, which is the
default post-reset setting, to be sure the regulator is set to a
valid value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Configure the clock settings before reconfiguring any other IO settings.
This is required when the clock must be stopped before changing eg. the
pin configuration or any of the other properties of the bus. Running the
clock configuration first allows the MMC core to do just that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
In case the controller performs card tuning, that is, sends MMC
command 19 or 21, silence possible CRC error warning prints. The
warnings are bound to happen, since the tuning will fail for some
settings while searching for the optimal configuration of the bus
and that is perfectly OK.
This patch passes around the MMC command structure and adds check
into tmio_sd_check_error() to avoid printing CRC error warning
when the tuning happens.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Properly handle return values and abort operations when they are
non-zero. This is a minor improvement, which fixes two remaining
unchecked return values.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
