| Age | Commit message (Collapse) | Author |
|---|
|
- Various MTD fixes from Boris
- Zap various unused / legacy paths.
- pxa3xx NAND update from Miquel
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add support for disabling subpage write support via
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE.
Currently the Linux Arasan driver does not support subpage writes and in
case of running UBI and accessing the same UBI volume from both U-Boot
and Linux it is required to have the same subpage write configuration
else the location of the UBI headers (EC + VID) will be misaligned
(subpage vs page) and incompatible. Hence the need for disabling
subpage write support in the U-Boot Arasan NAND driver.
Signed-off-by: Martin Lund <malu@gomspace.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The initial layout for such NAND chips was the following:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 32 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
This layout has a weakness: reading empty pages trigger ECC errors
(this is expected), but the hardware ECC engine tries to correct the
data anyway and creates itself bitflips, hence bitflips are detected
in erased pages while actually there are none in the NAND chip.
Two solutions have been found at the same time. One was to enlarge the
free OOB area to 64 bytes, changing the layout to be:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 64 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
^^
The very big drawbacks of this solution are:
1/ It prevents booting from NAND.
2/ The current Linux driver (marvell_nand) does not have such problem
because it already re-reads possible empty pages in raw mode before
checking for bitflips. Using different layouts in U-Boot and Linux
would simply not work.
As this driver does support raw reads now and uses it to check for
empty pages, let's forget about this broken hack and return to the
initial layout with only 32 free OOB bytes.
Fixes: ac56a3b30c ("mtd: nand: pxa3xx: add support for 2KB 8-bit flash")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
This only applies on BCH path.
When an empty page is read, it triggers an uncorrectable error. While
this is expected, the ECC engine might produce itself bitflips in the
read data under certain layouts. To overcome this situation, always
re-read the entire page in raw mode and check for the whole page to be
empty.
Also report the right number of bitflips if there are any.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
Raw read support is added by editing a few code sections:
->handle_data_pio() includes the ECC bytes that are not consumed
anymore by the ECC engine.
->prepare_set_command() is changed so that the ECC bytes are
requested as part of the data I/O length.
->drain_fifo() shall also avoid checking the R/B pin too often
when in raw mode.
->read_page_raw()/->read_oob_raw() are written from scratch.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
Testing and analysis shows that at the moment LPC32xx NAND SLC driver
can not get PL080 DMA backbone support in SPL build, because SPL NAND
loaders operate with subpage (ECC step to be precisely) reads, and
this is not supported in the NAND SLC + DMA + hardware ECC calculation
bundle.
The change removes a cautious build time warning and explicitly
disables DMA flavour of the driver for SPL builds, to reduce the
amound of #ifdef sections the code blocks are minimally reorganized.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Build option CONFIG_SYS_MAX_NAND_CHIPS is used by NXP LPC32xx NAND MLC
driver only, as a preparation for potential removal or replacement of
the option the change predefines CONFIG_SYS_MAX_NAND_CHIPS to 1, same
value is used by the single user Work Microwave Work 92105 board, thus
it will be safe now to remove the option as a board specific one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently in pmecc_get_sigma(), the code tries to clear the memory
pointed by smu with wrong size 'sizeof(int16_t) * ARRAY_SIZE(smu)'.
Since smu is actually a pointer, not an array, so ARRAY_SIZE(smu)
does not generate correct size to be cleared.
In fact, GCC 8.1.0 reports a warning against it:
error: division 'sizeof (int16_t * {aka short int *}) / sizeof (int16_t
{aka short int})' does not compute the number of array elements
[-Werror=sizeof-pointer-div]
Fix it by using the correct size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Sync the Kconfig raw NAND entry title with the code architecture.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
