summaryrefslogtreecommitdiff
path: root/drivers/mtd/nand
AgeCommit message (Collapse)Author
2014-12-11driver/mtd: Fix IFC compilation warningsJaiprakash Singh
'eccstat' array elements might be used uninitialized Signed-off-by: Jaiprakash Singh <b44839@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11arm: ls102xa: Add NAND boot support for LS1021AQDS boardAlison Wang
This patch adds NAND boot support for LS1021AQDS board. SPL framework is used. PBL initialize the internal RAM and copy SPL to it, then SPL initialize DDR using SPD and copy u-boot from NAND flash to DDR, finally SPL transfer control to u-boot. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-04mtd: nand: omap_gpmc: Always use ready/busy pinStefan Roese
The functions to detect the state of the ready / busy signal is already available but only used in the SPL case. Lets use it always, also for the main U-Boot. As all boards should have this HW connection. Testing on Siemens Draco (am335x) showed a small perfomance gain by using this ready pin to detect the NAND chip state. Here the values tested on Draco with Hynix 4GBit NAND: Without NAND ready pin: U-Boot# time nand read 80400000 0 400000 NAND read: device 0 offset 0x0, size 0x400000 4194304 bytes read: OK time: 2.947 seconds, 2947 ticks With NAND ready pin: U-Boot# time nand read 80400000 0 400000 NAND read: device 0 offset 0x0, size 0x400000 4194304 bytes read: OK time: 2.795 seconds, 2795 ticks So an increase of approx. 5%. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Roger Meier <r.meier@siemens.com> Cc: Samuel Egli <samuel.egli@siemens.com>
2014-11-26mtd: nand: s3c: Unify the register definition and namingMarek Vasut
Merge struct s3c2410_nand and struct s3c2440_nand into one unified struct s3c24x0_nand. While at it, fix up and rename the functions to retrieve the NAND base address and fix up the s3c NAND driver to reflect this change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Vladimir Zapolskiy <vz@mleia.com>
2014-11-26mtd/nand/vf610_nfc: Disable subpage writesSanchayan Maity
This patch disables subpage writes for vf610_nfc nand driver. This is required, as without this fix, writing unaligned u-boot images with DFU results in a hang. Trying to write unalgined binary images also results in a hang, without disabling subpage writes. Patch has been tested on a Colibri VF61 module. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2014-11-26mtd: denali: set some registers after nand_scan_ident()Masahiro Yamada
Some but not all of implementations of the Denali NAND controller have hardware circuits to detect the device parameters such as page_size, erase_size, etc. Even on those SoCs with such hardware supported, the hardware is known to detect wrong parameters for some nasty (almost buggy) NAND devices. The device parameters detected during nand_scan_ident() are more trustworthy. This commit sets some hardware registers to mtd->pagesize, mtd->oobsize, etc. in the code between nand_scan_ident() and nand_scan_tail(). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Chin Liang See <clsee@altera.com>
2014-11-26mtd: denali: use CONFIG_SYS_NAND_SELF_INITMasahiro Yamada
Some variants of the Denali NAND controller need some registers set up based on the device information that has been detected during nand_scan_ident(). CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between nand_scan_ident() and nand_scan_tail(). It is also helpful to reduce the difference between this driver and its Linux counterpart because this driver was ported from Linux. Moreover, doc/README.nand recommends to use CONFIG_SYS_NAND_SELF_INIT. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Chin Liang See <clsee@altera.com>
2014-11-26nand: reinstate lazy bad block scanningRostislav Lisovy
Commit ff94bc40af3481d47546595ba73c136de6af6929 ("mtd, ubi, ubifs: resync with Linux-3.14") accidentally reverted part of the commit 13f0fd94e3cae6f8a0d9fba5d367e311edc8ebde ("NAND: Scan bad blocks lazily."). Reinstate the change as by commit fb49454b1b6c7c6e238ac3c0b1e302e73eb1a1ea ("nand: reinstate lazy bad block scanning") Signed-off-by: Rostislav Lisovy <lisovy@merica.cz> Acked-by: Heiko Schocher <hs@denx.de>
2014-11-23linux/kernel.h: sync min, max, min3, max3 macros with LinuxMasahiro Yamada
U-Boot has never cared about the type when we get max/min of two values, but Linux Kernel does. This commit gets min, max, min3, max3 macros synced with the kernel introducing type checks. Many of references of those macros must be fixed to suppress warnings. We have two options: - Use min, max, min3, max3 only when the arguments have the same type (or add casts to the arguments) - Use min_t/max_t instead with the appropriate type for the first argument Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Pavel Machek <pavel@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> [trini: Fixup arch/blackfin/lib/string.c] Signed-off-by: Tom Rini <trini@ti.com>
2014-11-17mtd: atmel_nand: runtime to build gf table for pmeccJosh Wu
As in SAMA5D4 SoC, the gf table in ROM code can not be seen. So, when we try to use PMECC, we need to build it when do initialization. Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it is defined we will build gf table runtime. The PMECC use the BCH algorithm, so based on the build_gf_tables() function in lib/bch.c, we can build the Galois Field lookup table. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17spl, mtd, nand, atmel_nand: invert device ready pin logicHeiko Schocher
device ready pin is signalling that the device is ready on state 1 not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Reviewed-by: Bo Shen <voice.shen@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17spl, nand, atmel_nand: add erase one block functionHeiko Schocher
erase one nand block in spl code. keep it simple, as size matters This is used on the upcoming taurus spl support. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17mtd: atmel_nand: add missing includeHeiko Schocher
using this driver in SPL code with CONFIG_SPL_NAND_ECC configured leads in an compileerror. Fix this. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Reviewed-by: Bo Shen <voice.shen@atmel.com> [fix subject] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-05Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2014-10-30mtd: nand: mxs: Add ECC geometry for 2048b/112b NANDMarek Vasut
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB size. This is for example Macronix MX30LF2G28AB chip. Signed-off-by: Marek Vasut <marex@denx.de>
2014-10-25omap_gpmc: fix warnigs with W=1Jeroen Hofstee
- make omap_spl_dev_ready static - make omap_reverse_list static, move to under CONFIG_NAND_OMAP_ELM Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Signed-off-by: Tom Rini <trini@ti.com>
2014-10-23arm: marvell: Move arch/kirkwood.h to arch/soc.hStefan Roese
This move makes is possible to use this header not only from kirkwood platforms but from all Marvell mvebu platforms. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Luka Perkov <luka@openwrt.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-11Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-10-09mtd: denali: support NAND_CMD_RNDOUT commandMasahiro Yamada
The function nand_flash_detect_ext_param_page() requires NAND_CMD_RNDOUT command supported. It is necessary to detect some types of ONFi-compliant devices. Without it, the error message "unsupported command received 0x5" is shown. Let's support this command on the Denali NAND controller driver. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Chin Liang See <clsee@altera.com>
2014-10-09mtd: denali: fix NAND_CMD_PARAM commandMasahiro Yamada
NAND_CMD_PARAM (0xEC) command is not working on the Denali NAND controller driver. Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command is followed by an address cycle, the target device goes busy. (R/B# is deasserted) Wait until the parameter data are ready. In addition, unnecessary clear_interrupts() should be removed. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Chin Liang See <clsee@altera.com>
2014-10-08Merge remote-tracking branch 'u-boot-imx/master'Albert ARIBAUD
The single file conflict below is actually trivial. Conflicts: board/boundary/nitrogen6x/nitrogen6x.c
2014-10-05mtd: denali: add Denali NAND driver for SPLMasahiro Yamada
The SPL-mode driver for Denali(Cadence) NAND Flash Memory Controller IP. This driver requires two CONFIG macros: - CONFIG_SPL_NAND_DENALI Define to enable this driver. - CONFIG_SYS_NAND_BAD_BLOCK_POS Specify bad block mark position in the oob space. Typically 0. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Chin Liang See <clsee@altera.com> Cc: Scott Wood <scottwood@freescale.com>
2014-10-05mtd: denali: add Denali controller configs to KconfigMasahiro Yamada
Commit 3eb3e72a3f66 (nand/denali: Adding Denali NAND driver support) introduced some new options, and some of them were documented by commit f9860cf081ef (nand/denali: Document CONFIG symbols). This commit allows users to enable/disable them via Kconfig with more detailed help docs. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Chin Liang See <clsee@altera.com> Cc: Scott Wood <scottwood@freescale.com>
2014-09-26Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2014-09-25nand/denali: Adding Denali NAND driver supportChin Liang See
To add the Denali NAND driver support into U-Boot. This driver is leveraged from Linux with commit ID fdbad98dff8007f2b8bee6698b5d25ebba0471c9. For Denali controller 64 variance, you need to declare macro CONFIG_SYS_NAND_DENALI_64BIT. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-25mtd: nand: Fix length bug in ioread16_rep() and iowrite16_rep()Stefan Roese
The ioread16_rep() and iowrite16_rep() implementations are U-Boot specific and have been introduced with the Linux MTD v3.14 sync. While introducing these functions, the length for the loop has been miscalculated. The ">> 1" is already present in the caller. So lets remove it in the function. Tested on omap3_ha. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
2014-09-25mtd: nand: am335x: Fix 'bit-flip' errors in SPLRostislav Lisovy
OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip corrected' error messages. Possible cause was discussed in the mailinglist thread: http://lists.denx.de/pipermail/u-boot/2014-April/177508.html The issue was partially fixed with the cc81a5291910d7a.git however this has to be done to fix the SPL. The original author of the code is Belisko Marek <marek.belisko@gmail.com> Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-25driver/mtd: Use generic timer API for FSL IFC, eLBCPrabhakar Kushwaha
Freescale's flash control driver is using architecture specific timer API i.e. usec2ticks Replace usec2ticks with get_timer() (generic timer API) Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-22Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic
2014-09-19mtd: atmel_nand: Disable subpage NAND write when using Atmel PMECCBoris BREZILLON
Disable subpage write when using PMECC to prevent buggy partial page write. This fix has been taken from linux sources (see commit 90445ff6241e2a13445310803e2efa606c61f276) Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Acked-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19mtd: atmel-nand: use pmecc_readl(b)/pmecc_writel to access the pmecc registerWu, Josh
We defined the macro pmecc_readl(b)/pmecc_writel for pmecc register access. But in the driver we also use the readl(b)/writel. To keep consistent, this patch make all use pmecc_readl(b)/pmecc_writel. Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-16mtd: nand: davinci_nand: update write_page function for keystone RBLKhoronzhuk, Ivan
After mtd was synced with Linux 3.14 (ff94bc40af3481d47546595ba73c136de6af6929) the number of parameters for write_page function of nand_chip was changed. The additional two var were needed for subpage write. As keystone has no supbage write they are not needed. So correct only function definition by upgrading it's parameter list. That helps to get ritd of compilation warning. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-16kbuild: force to define __UBOOT__ in all the C sourcesMasahiro Yamada
U-Boot has imported various source files from other projects, mostly Linux. Something like #ifdef __UBOOT__ [ modification for U-Boot ] #else [ original code ] #endif is an often used strategy for clarification of adjusted parts, that is, easier re-sync in future. Instead of defining __UBOOT__ in each source file, passing it from the top Makefile would be easier. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2014-09-16mtd: nand: add Freescale vf610_nfc driverStefan Agner
This adds initial support for Freescale NFC (NAND Flash Controller) found in ARM Vybrid SoC's, Power Architecture MPC5125 and others. The driver is called vf610_nfc since this is the first supported and tested hardware platform supported by the driver. Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
2014-09-04mtd: nand: omap_gpmc: Fix 'bit-flip' errorsRostislav Lisovy
OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip corrected' error messages. Possible cause was discussed in the mailinglist thread: http://lists.denx.de/pipermail/u-boot/2014-April/177508.html Quote (Author: Pekon Gupta <pekon@ti.com>): "The issue is mainly due to a NAND protocol violation in the omap driver since the Random Data Output command (05h-E0h) expects to see only the column address that should be addressed within the already loaded read page into the read buffer. Only 2 address cycles with ALE active should be provided between the 05h and E0h commands. The Page read command expects the full address footprint (2bytes for column address + 3bytes for row address), but once the page is loaded into the read buffer, Random Data Output should be used with only 2bytes for column address." This patch combines the solution proposed in the mailinglist and the patch provided by the Spansion company (GPLv2 code, source: http://www.spansion.com/Support/Software/u-boot-psp-04.04.00.01-NAND.zip) Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-04mtd: nand: omap_gpmc: Enable multiple NAND flash devicesRostislav Lisovy
Since the CS of a device connected to the GPMC was stored in the global variable, it was not possible to use multiple devices. In this patch the CS is stored per device in its 'struct omap_nand_info'. This makes it possible to use up to 'GPMC_MAX_CS' NAND Flash devices connected to U-boot. Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-04mtd: nand: davinci_nand: correct keystone RBL layout definitionKhoronzhuk, Ivan
In case when 4K page keystone RBL layout is used the compilation error is appeared. That's because the #ifdef has to be placed under struct name. This patch correct it. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-08-30arm/kirkwood/nand: allow forced disabling for subpage writesHolger Brunck
Make it configurable to disable subpage writes like the DaVinci NAND driver already does. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Scott Wood <scottwood@freescale.com>
2014-08-25mtd,ubi,ubifs: sync with linux v3.15Heiko Schocher
snyc with linux v3.15: commit 1860e379875dfe7271c649058aeddffe5afd9d0d Author: Linus Torvalds <torvalds@linux-foundation.org> Date: Sun Jun 8 11:19:54 2014 -0700 Linux 3.15 Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@ti.com>
2014-08-25mtd, ubi, ubifs: resync with Linux-3.14Heiko Schocher
resync ubi subsystem with linux: commit 455c6fdbd219161bd09b1165f11699d6d73de11c Author: Linus Torvalds <torvalds@linux-foundation.org> Date: Sun Mar 30 20:40:15 2014 -0700 Linux 3.14 A nice side effect of this, is we introduce UBI Fastmap support to U-Boot. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Cc: Sergey Lapin <slapin@ossfans.org> Cc: Scott Wood <scottwood@freescale.com> Cc: Joerg Krause <jkrause@posteo.de>
2014-07-29Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-07-25mtd: nand: davinci: add opportunity to write keystone U-boot imageKhoronzhuk, Ivan
The Keystone SoCs use the same NAND driver as Davinci. This patch adds opportunity to write Keystone U-boot image to NAND device using appropriate RBL ECC layout. This is needed only if RBL boots U-boot from NAND device and that's supposed that raw u-boot partition is used only for writing image. The main problem is that default Davinci ECC layout is different from Keystone RBL layout. To read U-boot image the RBL needs that image was written using RBL ECC layout. The BBT table is written using default Davinci layout and has to be updated using one. The BBT can be updated only while erasing chip or by forced bad block assigning, so erase function has to use native ecc layout in order to be able to write BBT correctly. So if we're writing to NAND U-boot address we use RBL layout for others we use default ECC layout. Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no reasons to use ECC layout commands. It was added by mistake. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-22driver/nand: Add support of 16K SRAM for IFC 2.0Prabhakar Kushwaha
Internal SRAM has been incresed from 8KB to 16KB for IFC cotroller ver 2.0. Update the page offset calculation logic to support the same. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22driver/nand: Update SRAM initialize logic for IFC.Prabhakar Kushwaha
IFC controller v1.1.0 requires internal SRAM initialize by reading NAND flash. Higher controller versions have provided "SRAM init" bit in NCFGR register space. update SRAM initialize logic to reflect the same. Also print error message in case of Page read error. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22driver/nand:Define MAX_BANKS same as SoC defined for IFCPrabhakar Kushwaha
The number of chip select used by IFC controller vary from one SoC to other. For eg. P1010 has 4, T4240 has 8. Update MAX_BANKS same as SoC defined Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-01Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-06-30Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-06-19mtd: nand: davinci: add header file for driver definitionsKhoronzhuk, Ivan
The definitions inside emif_defs.h concern davinci nand driver and should be in it's header. So create header file for davinci nand driver and move definitions from emif_defs.h and nand_defs.h to it. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> [trini: Fixup more davinci breakage] Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06mtd: nand: omap: add support for BCH16_ECC - NAND driver updatespekon gupta
This patch add support for BCH16_ECC to omap_gpmc driver. *need to BCH16 ECC scheme* With newer SLC Flash technologies and MLC NAND, and large densities, pagesizes Flash devices have become more suspectible to bit-flips. Thus stronger ECC schemes are required for protecting the data. But stronger ECC schemes have come with larger-sized ECC syndromes which require more space in OOB/Spare. This puts constrains like; (a) BCH16_ECC can correct 16 bit-flips per 512Bytes of data. (b) BCH16_ECC generates 26-bytes of ECC syndrome / 512B. Due to (b) this scheme can only be used with NAND devices which have enough OOB to satisfy following equation: OOBsize per page >= 26 * (page-size / 512) Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device ↵pekon gupta
bus-width GPMC controller needs to be configured based on bus-width of the NAND device connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI parameters is not possible in following situations: SPL: SPL NAND drivers does not support ONFI parameter reading. U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init() which is called before probing for devices, hence any ONFI parameter information is not available during GPMC initialization. Thus, OMAP NAND driver expected board developers to explicitely write GPMC configurations specific to NAND device attached on board in board files itself. But this was troublesome for board manufacturers as they need to dive into lengthy platform & SoC documents to find details of GPMC registers and appropriate configurations to get NAND device working. This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config hich indicates that connected NAND device has x16 bus-width. And then based on this config GPMC driver itself initializes itself based on NAND bus-width. This keeps board developers free from knowing GPMC controller specific internals. Signed-off-by: Pekon Gupta <pekon@ti.com>
generated by cgit (git 2.34.1) at 2024-12-27 19:06:27 +0000