| Age | Commit message (Collapse) | Author |
|---|
|
I can't find anywhere in the datasheet that says the status register needs
3 dummy bytes sent to it before being able to read back the first real
result. Tests on a Blackfin board show that after writing the opcode, the
status register starts coming back immediately. So only write out the
read status register opcode before polling the result.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Since timeouts are only hit when there is a problem in the system, we
don't want to prematurely timeout on a functioning setup. Thus having
low timeouts (in milliseconds) doesn't gain us anything in the production
case, but rather increases likely hood of causing problems where none
otherwise exist.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Some SPI flash drivers like to have extended id information available
(like the spansion flash), so rather than making it re-issue the ID cmd
to get at the last 2 bytes, have the common code read 5 bytes rather than
just 3. This also matches the Linux behavior where it always reads 5 id
bytes from all flashes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Mingkai Hu <Mingkai.hu@freescale.com>
|
|
The common SPI flash code reads the idcode and passes it down to the SPI
flash driver, so there is no need to read it again ourselves.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
- AT45DB321D
- AT45DB161D
- AT45DB081D
- AT45DB041D
- AT45DB021D
- AT45DB011D
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Add MTD SPI Flash support for S25FL008A, S25FL016A,
S25FL032A, S25FL064A, S25FL128P.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Higher spi flash layers expect to be given back a pointer that was
malloced so that it can free the result, but the lower layers return
a pointer that is in the middle of the malloced memory. Reorder the
members of the lower spi structures so that things work out.
Signed-off-by: Brad Bozarth <bflinux@yumbrad.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
The stmicro_wait_ready() func tries to show the actual opcode that was sent
to the device, but instead it displays the array pointer. Fix it to pull
out the opcode from the start of the array.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Add MTD SPI Flash support for M25P16, M25P20, M25P32,
M25P40, M25P64, M25P80, M25P128.
Signed-off-by: Jason McMullan <mcmullan@netapp.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This adds a new SPI flash subsystem.
Currently, only AT45 DataFlash in non-power-of-two mode is supported,
but some preliminary support for other flash types is in place as
well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
