| Age | Commit message (Collapse) | Author |
|---|
|
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
commit c3c016c "sf: Add SPI NOR protection mechanism" introduced
flash_lock()/flash_unlock()/flash_is_locked() methods for SPI flash,
but not every flash driver supplies these. We should test these
methods against NULL before actually calling them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
The current error message in get_part if CONFIG_MTDPARTS is disabled is
"offset is not a number" which is confusing and doesn't help at all.
Change that for something that might give a hint on what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add Altera Generic Quad SPI Controller support. The controller
converts SPI NOR flash to parallel flash interface. So it is
not like other SPI flash, but rather like CFI flash.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
|
|
Convert cfi flash to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Implement a Memory Technology Device (MTD) uclass. It should
include most flash drivers in the future. Though no uclass ops
are defined yet, the MTD ops could be used.
The NAND flash driver is based on MTD. The CFI flash and SPI
flash support MTD, too. It should make sense to convert them
to MTD uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
|
|
Many SPI flashes have protection bits (BP2, BP1 and BP0) in the
status register that can protect selected regions of the SPI NOR.
Take these bits into account when performing erase operations,
making sure that the protected areas are skipped.
Tested on a mx6qsabresd:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
=> sf protect lock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
offset 0x3f0000 is protected and cannot be erased
SF: 65536 bytes @ 0x3f0000 Erased: ERROR
=> sf protect unlock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
SF: 65536 bytes @ 0x3f0000 Erased: OK
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
[re-worked to fit the lock common to dm and non-dm]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Add the SPI NOR protection mechanism from the kernel.
This code is based on the work from
Brian Norris <computersforpeace@gmail.com>
Here is the commit details:
"mtd: spi-nor: refactor block protection functions"
(sha1: 62593cf40b23b523b9fc9334ca61ba6c595ebb09)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
|
|
|
|
|
|
This patch changes the cword union to use specific length types that are
architecture indepented.
This patch also renames the members of the cword union to represent
their usage, i.e.:
c -> w8
s -> w16
l -> w32
ll -> w64
Where "w" stands for "width" in bits.
I discovered this problem when enabling CFI flash on vexpress64.
cword.l was an unsigned long int, but it was intended to be 32 bits wide.
Unfortunately, it's 64-bits wide on a 64-bit system, meaning that a
64-bit system fails when attempting to use 32-bit wide CFI flash parts.
Similar problems also existed with the other cword sizes.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The PEB array is an array of __be32, so let's fix the
scan_pool() prototype accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
sync with linux v4.2
commit 64291f7db5bd8150a74ad2036f1037e6a0428df2
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Aug 30 11:34:09 2015 -0700
Linux 4.2
This update is needed, as it turned out, that fastmap
was in experimental/broken state in kernel v3.15, which
was the last base for U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
|
|
This patch adds flag status register reading support to
spi_flash_cmd_wait_ready.
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Hou Zhiqiang <B48286@freescale.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Current flash wait_ready logic is not modular to add new
register status check, hence updated the status check for
adding few more register checks in future.
Below are the sf speed runs with 'sf update' on whole flash, 16MiB.
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 59.564s, speed 289262 B/s
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 62.549s, speed 275036 B/s
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 61.276s, speed 284359 B/s
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use the flash->flags for generic usage, not only for dm-spi-flash,
this will be used for future flag additions.
[Correct the spi flash flags detect logic]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Optimized spi-flash bar writing code and also removed
unnecessary bank_sel in read_ops.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Add spi_flash_read_bar function for reading bar and
discovering bar commands at probe time.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
If computed bank_sel is same as flash->bank_curr which is
computed at probe time, then return the bank_sel instead of zero.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Added support for IS25LP128 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
Added support for IS25LP064 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
Added support for IS25LP032 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
|
|
This resyncs the driver changes with the Linux version of the
driver. The driver received some feedback in the LKML and got
recently acceppted, the latest version can be found here:
https://lkml.org/lkml/2015/9/2/678
Notable changes are:
- On ECC error, reread OOB and count bit flips in OOB too.
If flipped bits are below threshold, also return an empty
OOB buffer.
- Return the amount of bit flips in vf610_nfc_read_page.
- Use endianness aware vf610_nfc_read to read ECC status.
- Do not enable IDLE IRQ (since we do not operate with an
interrupt service routine).
- Use type safe struct for buffer variants (vf610_nfc_alt_buf).
- Renamed variables in struct vf610_nfc (column and page_sz)
to reflect better what they really representing.
The U-Boot version currently does not support RAW NAND write
when using the HW ECC engine.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Scott Wood <scottwood@freescale.com>
|
|
Messages on corrected bit-flips are not really useful,
as bit-flips are perfectly normal. Let's avoid cluttering
the console and make them debug.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
|
|
AT26DF081A is the spi flash type of TWR-MEM(SCH-26248) card.
We can access the flash through DSPI2 on LS1021ATWR board.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
We know when u-boot is written to its own partition, in this case the
layout always is:
eb 0 spl
eb 1 spl-backup
eb 2 u-boot
eb 3 u-boot-backup
eb: erase-block
So if we cannot load u-boot from its primary offset we know exactly where
to look for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Check maximum ecc strength for each platfrom to avoid the calculated ecc
exceed the limitation.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Han Xu <b45815@freescale.com>
Tested-By: Tim Harvey <tharvey at gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
This patch addresses some comments raised by Scott in the last versions.
Here the changes in detail:
- Removed __maybe_unused as its not needed
- Added check for strength == 4 and error out for the unsupported
ECC strength values
- Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this
will be done in nand_scan_tail()
- Set .caclulate back to fsmc_read_hwecc() in the HW case
- Added comment that this function will only be called on SPEAr platforms,
not supporting the BCH8 HW ECC (FSMC_VER8)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Scott Wood <scottwood@freescale.com>
|
|
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present malloc.h is included everywhere since it recently was added to
common.h in this commit:
4519668 mtd/nand/ubi: assortment of alignment fixes
This seems wasteful and unnecessary. We have been trying to trim down
common.h and put separate functions into separate header files and that
change goes in the opposite direction.
Move malloc_cache_aligned() to a new header so that this can be avoided.
The header would perhaps be better named as alignmem.h but it needs to be
included after common.h and people might be confused by this. With the name
memalign.h it fits nicely after malloc() in most cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your config header:
#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH
And use the command "nandecc bch4" to select this ECC scheme upon runtime.
Tested on SPEAr600 x600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds support for NAND chips with 4KiB page size and 24/1024
ECC strength. Like the Micron MT29F32G08CBACAWP which is used on the
ICnova-A20 SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.
Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>
|
|
Some status flags remain set until you explicetly clear the bit
in the status register.
Fix the SPL implementation to avoid false positive.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[hdegoede@redhat.com: Port from v2015.07 to v2015.10]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
We only ever use syndrome mode for the partitions which contain the SPL,
as that is required for the BROM to be able to read the SPL.
Instead of using some arbritray limit for deciding whether or not to
use syndrome, be smart and check if u-boot-dtb.bin is directly behind
the SPL, if it is not then it is on its own partition and we should not
use syndrome.
Note the reason why we only use syndrome mode for the SPL is because it
comeswith weaker randomization, introducing a risk for more bit errors,
so we want to avoid it when possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.
Renaming the Kconfig option now makes things easier when we add full
nand support in the future.
The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The BROM does not care / use bad page markings, instead it deals with
any bad pages in the first erase-block by simply trying to load "boot0"
from the next erase-block.
This commit implements the same strategy for the sunxi spl nand code,
allowing it to boot from the backup boot partition when the main boot
partition is bad (tested by erasing the main boot partition).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Auto detect the nand configuration parameters, like the BROM does.
This allows us to get rid of various Kconfig settings, and is
necessary to support generic boards like the mk802 which have seen
many production runs with different nands.
The full blown u-boot/kernel nand driver uses the nand id to determine
this info, for the SPL we do as the BROM does and simply try a few
standard configs.
Note the table only contains configs which are known to actually be used,
rather then all the configs the BROM tries. This means that it may need
to be updated in the future as we add support for nand on more boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Parametrize the lowlevel nand_read_page function, instead of directly
using the CONFIG_foo settings for page-size, etc. there and add a few
wrappers / helper functions for calling it.
This is a preparation patch for adding auto-detecting of the nand
parameters like the BROM does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Properly config page-size in the nand ctl register, it seems that things
work fine without doing this, but still lets play it safe and properly
set the page-size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.
Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Sync the code for figuring out the ecc_mode and ecc_offset with the linux
kernel v4.1. Keeping this in sync seems like a good idea in general, and
it fixes / adds support for ecc strengths of 56, 60 and 64 bits.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
We are using dma, so we should flush the cache before starting the dma,
and invalidate it once the dma is done.
Things are working without this by mostly luck, but lets not rely on that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
